How to Install Trawler Rub Rail | Sailboat Restoration and Pocket Trawler Refit (Ep46)

Рет қаралды 4,764

11 ай бұрын

Installing New Rub Rail on your boat building or boat restoration project can be a challenging job. This episode I talk about the construction of my hull deck joint on my Albin 27 pilothouse trawler. I install new rubber rub rail repairing the outer hull flange.
Welcome to my boat building channel! This is my trawler restoration of an Albin 27 pocket trawler. Every couple of weeks I post a boat building or boat repair video to document various boat projects, sailboat restorations, or boat repairs.
**MotorCity Boat Werks has no sponsors and receives no compensation from any of the brands featured or recommended.
However, there may be compensation from the use of Amazon affiliate links below.**
Be sure to like and subscribe.
/ motorcityboatwerks
Questions or comments can can be submitted via the comments section or at:
📧motorcityboatwerks.weebly.com/...
Donations or to join The Werkers (fan club):
/ motorcityboatwerks
#boatprojects #boatrefit #boatrestoration #boatbuilding #trawlervlog #trawler #boatlife #sailboatrestoration #sailboatrefit #boatworkstoday #waverover #motorcityboatwerks
My videos are similar to boat project restoration videos like Boat Works Today; My videos are similar to boat project restoration videos like Boat Works Today; Project Brupeg; Sampson Boat Co; The Duracell Project; Project Duracell; Tula's Endless Summer; Sailing Delos; Sail Life; Travels with Geordie; SV Seeker; Danger Marine; My First Boat; Sailing Dawn Hunters; Seeking Seas; Sailing Flying Coney; AYO Fishing; Peter Slack; Sail Life; Wilding Sailing; Life on the Hulls; Sailing Wave Rover; SV Tapatya; LOJO Fishing; Sailing Wave Rover; Angry Mack

Пікірлер: 20

@wolframschweier3307 11 ай бұрын

I agree any lube material would make attachment more difficult and strenuous. As an alternative, I think the wood wedge approach could work better but you'd need an assistant to work a long wedge to pry the rail opening just ahead of you wrestling the rail on the to boat. I guess the Werkers are taking vacation.

@motorcityboatwerks 11 ай бұрын

I was thinking of something almost shoe-horn hammer like with a handle that might have allowed the material pried open as you scooted it along the hull flange and insert 👍

@obxarms7685 3 ай бұрын

Great video thanks

@motorcityboatwerks 3 ай бұрын

Thank you for the comment 😁👍 Be sure to subscribe and spread the word.

@907T 11 ай бұрын

Great job Joe.

@motorcityboatwerks 11 ай бұрын

Thanks Joe 😁👍

@martylasher539 11 ай бұрын

I have never done this job, but I would be tempted to hook up a come-along to each of those aft ends and give them a good tug while going at them with a heat gun. Then I'd anchor the ends with a couple of rivets with washers that would hide under your new corner trim pieces. Won't that PVC creep around when the weather gets hot unless it's pre-loaded? Just two cents worth from the peanut gallery. :-). I really appreciate that you share the struggle and don't just fast-forward over the frustrating parts. This sure looks like a lot of my projects. Just one little line on the to-do list...

@motorcityboatwerks 11 ай бұрын

Thank you Marty. I do not anticipate much linear shrinkage. Plenty of room for movement. The corner end caps will likely me attached with marine sealant

@JohansGrandBanksSaabEtc 11 ай бұрын

Heavy job, you're a fighter! Well done! Also it's super cool to be a Patreon inside your shop. Keep it up.

@motorcityboatwerks 11 ай бұрын

Thank you Johan! I could not do it without you 🫡 😁👍

@CaptMarkSVAlcina 9 ай бұрын

What about a hot water heater tank with the rub rail in it. As you move along it comes out of hot water and keeps the other end in hot water. And also keeping the hot water hot . Maybe have it on a trolley as you move around the boat ?

@motorcityboatwerks 9 ай бұрын

This is a good idea. I actually thought that if you had a hot tub running at about 102-104 degrees you could warm the entire coil quite a bit -pull it out and then attempt a quick install.

@gnsmk357 11 ай бұрын

Looks good. I would have used a lot of WD 40. This would not have opened up the rail but once it was open it may have moved a bit quicker. Go Motor ciry boat works.

@motorcityboatwerks 11 ай бұрын

Right the issue was opening it up. Any lube would have made it hard to hold onto.

@Amondiir 3 ай бұрын

Coming to this late, but I've heard feeding the rubber along the rail, starting at one aft corner, and either pulling or sliding along. No idea if thats effective, though. I'm about to embark on this same project for my Albin 27 FC, same year, so this is invaluable. Thank you!

@motorcityboatwerks 3 ай бұрын

Welcome Aboard Matt👍😁 Let me know how that works out😉