Great video thanks. Here's a tip if you have a crossbar that gets in the way of the Allen screw... (7/8" bar) Put everything together without worrying about the angle of the handguards. Then, loosely tighten the end of the handlebar, the two Allen screws on the U clamp, and the screw that passes through the aluminum handguard to the clamp. In other words, put it all together. Then, snug up the 5mm Allen screws on the U clamp - get them even - there should be about an eighth of an inch gap - as long as it's even it's good. THEN, move the whole thing to the level that you want. NEXT, if the crossbar is in the way of one of the Allen screws, DON'T WORRY ABOUT IT. Simply tighten up the other one that you can access. Tightening one tightens up both. I just did this on my DRZ400...
@jaspertaylor7455 Жыл бұрын
I've just purchased the TUSK HAND GUARDS and I was wondering how to install them and I found the information, provided, very, very helpful...THANK YOU KINDLY FOR YOUR HELP, ALWAYS...RIDE OR DIE...
@jaspertaylor7455 Жыл бұрын
Just bought these TUSK, PRO HANDGUARDS, and I needed instructions on installing them. THANK THE MOTORCYCLE GOD, for being RIGHT and LEFT, " GUARD ", ON TIME...THANK YOU KINDLY FOR EVERYTHING...
@davelariviere6824 жыл бұрын
Excellent install video. Thank you. I will be picking up a couple sets on the weekend. Cheers
@jakelucas38784 жыл бұрын
Just did this install on my 2019 CRF250L, super easy! The stock double bar kinda sucks for the clamps but it’s not hateful, will be switching bars out soon but glad I know the process installation!!
@literalfuckingtroll3 жыл бұрын
Google Translate!
@flurren43933 жыл бұрын
Great video! I have been looking for a good video for so long. Thank you, really!
@jhchevy1 Жыл бұрын
I bought these to put on my 2023 crf250f and I’m have a hard time getting the clamps to line up with the Stock handle bars. I’ve seen other videos where they just don’t lay flush.
@BHMoto3 жыл бұрын
Great video installation thanks so much !
@ericgoodrich593 Жыл бұрын
Thank you for the help.
@jeffreytuttle882515 күн бұрын
These won't work on my 2024 KLX handlebars. There is a steel insert at the end of the bars that will not allow the expanding bolt it. Bummed out....
@mrsmacksem53864 жыл бұрын
Are those shorty levers? My stick levers don’t fit they hit the bar
@joseroman3607Ай бұрын
Where do I Measure my handle bar to make sure if it is 7/8 or 1 1/8? I own a 2024 KTM 250 XC-W
@rmatvmcАй бұрын
Measure the center of the bars diameter. For your model it should be 1-1/8.
@sund52 жыл бұрын
Lol I did not cut enough away on the thottle tube. So everytime I droped the bike the thottle got stuck...
@pantinor2 жыл бұрын
Any tips for using this with 1 1/8 handle bars? Clamps Not good fitting as they are, but they can tightened down.
@active6302 Жыл бұрын
I bought 2 of these from Rocky Mountain ATV not realizing they were sold in pairs. So I returned one pair but they claimed they never received them and denied a refund. This company is a bunch of cork soakers as Redd Foxx would say!
@izaihawright4 жыл бұрын
So I got these but I run rental twinwall bar and they didn't fit is there any way to do maybe a different clam set up on the bar
@canusa5722 жыл бұрын
Same bars, I was able to make them fit by inverting the clamps (1 1/8) and trimming the cross bar padding.
@roadtripmemories2392 жыл бұрын
Hi, which one is suitable for KTM790ADV 1-1/8" or 7/8"?
@Zero-ey1wc2 жыл бұрын
Does anyone know what the piece is called that has the rubber spacer on it
@GR1MKA1 Жыл бұрын
I can't get these to fit my handle bars with a cross bar. Have a KLX300 and a KLX 110RL, it doesn't fit either of them. Even bought a tusk 7/8 handle bar for the 110RL, still doesn't fit.
@active6302 Жыл бұрын
Don`t send them back, you won`t get a refund.
@ezekielstark73664 жыл бұрын
Great video! About how much do these cost?
@rmatvmc4 жыл бұрын
The D-Flex Pro Handguards are $69.99.
@danielspackman71592 жыл бұрын
I have problems with the throttle hand being bound. up when I install my hand guards, how do I fix this?
@rmatvmc2 жыл бұрын
Move the throttle housing in far enough in that it won't rub on the hand guard. Also check to see if the rubber on the grip is dragging on the bar. If that's the case, trim a little off. Last, make sure the cable is routed correctly. If none of that works, let me know. -Charles
@davidclark55924 жыл бұрын
I replaced handlebars on my CRF 230 and am trying to get the plugs/inserts that go into the handlebars out of the old bars to install in the new bars or find just those parts inserts/plugs as replacement parts. Can I purchase those inserts separately?
@rmatvmc4 жыл бұрын
We don't sell those separately but we do have the ODI grip end plugs you could try out. www.rockymountainatvmc.com/parts/odi-aluminum-grip-end-plugs-p
@staceytrainer14 жыл бұрын
Will all tusk handguard shields work on the same mounting hardware? I have the regular D-Flex but can't find the replacements in orange but do see other types available in that color
@rmatvmc4 жыл бұрын
Some of the Tusk handguards can be swapped but the D-Flex and D-Flex Pro use a different aluminum bar so the Pro shields will not be a direct fit on your D-Flex bars.
@bikersoncall Жыл бұрын
7:10 Why isn't he wearing a helmet and respirator?
@kraigvanderwyk11535 ай бұрын
No mention of the brake line or worst yet the clutch line. These things are terrible design.