A random job that I thought you'd enjoy! 🛠 *_AMAZON TOOL STORE:_* www.amazon.co.uk/shop/plumberparts 🥾 *_10% Off my workboots + workwear Use Plumberparts10:_* elwoodworkwear.co.uk/?ref=Plumberparts10 👓 *_10% Off Safestyle Sunglasses Use PLUMBER10:_* safestyle.com.au/?ref=PLUMBER10

Of all the guides on fitting waste pipe, this is one

Why are waste pipes always taken upward before entering the pipework? Washing machines in particular don't pump all the water out once air gets in, which leaves stagnating water in the grey pipes.

the FUNNIEST part is you giving up and bringing in a trolley :D

Fire extinguishers are good for holding laser levels. You should have one around anyway!

Camera tripod works well for my laser level. It's got the right thread in the bottom.

Hi James, I hope them two machines don't discharge at the same time, coz that downpipe don't look long enough, it could back flow out the pipe, hope ya tested it!!

Let's see your cat George again please.❤

You can get adapters that provide a flat surface for the gasket at 11:01 instead of nipping up to a chamfered edge on that isolator.

I never use joining compound but I use Loctite threadlocker on the threads to be sure😉. great stuff

I will put my life on it that youll be the one fitting the new prv when it eventually goes 😂 great video 👍

Shouldn’t you install a double check valve before the washing machine connection ? Or is it not needed that’s how I’ve been taught

Gary Rowett

Question on how to achieve a decent fall on the drain pipe. The elbow fitting in the corner was glued so presumably not moving much. So do you just 'force' the pipe up at the downpipe side to create the fall?

Use a twin spigot adaptor with air vent is better than just shoving the 2 hoses in the down pipe

Where do you join the members area? I can’t find the link?

I never knew about cutting the rubber spigot off the appliance hose if it goes in to the upstand. hat happens if its left on?

I am in hospital tonight whiching your vlog

Just want to ask something. I have Willis Emersion heater attached to my hot water tank and if I try and use it then it seems to have gone into reverse flow!!!! The hot water should rise and enter the top of the tank but it seems to be blocked from flowing in that direction so it over boils (kettles apparently, people seem to use them for underfloor heating) and actually expels the hot water from the bottom (what is suppose to be the intake!) of the Willis unit so it can flow in that direction around the loop but not the normal direction which I suspect is some sort of debrie blocking the flow in one direction possibly and so it heats the hot water tank from the bottom and so takes ages and there is some amazing clanking and sucking orchestra to accompany it all lol. It used to work in the other correct direction but no longer so I guess it needs disassembled to see what is causing this possible blockage? It's an old awkward system to drain etc but when it worked properly it was great but now it's doing my head in.

Soo, just fix the new pipe over the valve handle and don't worry about it, job done, get paid, someone else's problem later? Got it.

Yes! Got to wear that lab coat. Elf n safety. You forgot the following: Anti slip, non-conductive, steel-toed work boots. Natural fibred socks with antibacterial enzymes. (Stops you having to see if they stick to the wall, before you change them) Comfy undies. Flame retardant, branded work trousers incorporating ranti rip fibres, elephant eared storage pockets (just don't let your trunk hang out in public) Gloves. Flame retardant shirt (bra is optional, even for men. Moooobs!) Stab vest, welders helmet, ear/nag defenders (See Loafer's missus) Air raid siren warning of impending doom and wallet on a sturdy chain. I must have forgotten something? 🤔 All suggestions appreciated.

check out the plumberparts mandem and their sick grimebeats on the intro fam!

All that science and not a single magnet or laser… when you order science from Wish

🔥

Why would anyone drill into mortar joints for a decent fixing!

I don’t agree with cutting the rubbers off. I’ve been using a twin spigot adapter compression fitting on a 40mm downpipe since 2010.

The thumb nail pic looks a bit naughty.....look at it again! Looks like youve whipped out ya chopper!

Very poor installation, If you cut into that waste pipe at the correct height then the pipe waste pipe you installed would not have crossed in front of that existing wall mounted valve, also the length of waste pipe you fitted along the wall would not have had to slope up so steeply in order for the U bend to miss the existing copper pipe work.

Why you dressed like neo

Compression fittings without compound just leak. Always leak.

Not Mcalpine urgh 😂

Them fluxuators are crap mate

Not one of your best jobs 😂. Back runs don’t work on ikea kitchens - have to do it at floor level