there are cell spacers very cheaply on various sales platforms. they better than gluing batteries together and safer too. also grade your cells, don't mix a 1.5AH and say a 1.2AH cell if you using reclaimed batteries
@hopehunterrider49110 ай бұрын
this video is best one so far...thanks for your work..
@swarnabpaul20409 ай бұрын
This dc jack should not be connected directly to the bms because it will give reverse charging you should connect with a diode 👍
@tenlittleindians Жыл бұрын
Your video title has a critical error. the 12.6v is correct but you used a comma instead of a period leading me to believe you somehow had a pack that could output both 12 volts and 6 volts. I figured that out after watching your video.
@curiousonlooker4770 Жыл бұрын
I'd like to see how you made your spot welder, but I have yet to look at what other videos you have, so I hope to be pleasantly surprised.
@sharukhmatekuki58302 жыл бұрын
Nice 👍🏻👍🏻 🇮🇳 Kuki 03|06|2022.
@Vagubando2 жыл бұрын
Do I need to connect (weld, solder) batteries to the BMS board in sequence (from plus to minus or vice versa) how is it in the laptop battery so that the board does not go into protection?
@zeknoss Жыл бұрын
Why do all the DIY channels feel the need of putting horrible music on their videos? I mean is this mandatory?
@consertosvintage7961 Жыл бұрын
Beautiful 👏👏👏👏
@Eric_Berserker Жыл бұрын
I want to ask you something. Is it normal for the resistor on the BMS to heat up when the battery is being soldered to it?
@n_e_h_a_l_ Жыл бұрын
I made an ups with 3s 25a BMS and 6cells of 18650. My router supports 12v 1.5amp. Can I use a 12v 5amp adapter to charge the ups alongside to power the router. 5a-1.5a=3.5amp for my 3s battery pack (6*18650 batteries total (🔋🔋+🔋🔋+🔋🔋)) Is it alright to use 12v 5a charger? Is it going to quickly reduce the battery lifespan?
@giorgioroascio84384 жыл бұрын
Hi DIY Lady, you are great, can you tell me which adapter you use to load the 6 pack?. And for a 3-pack which adapter do you need? Thank you from Italy
@diylady4 жыл бұрын
You need 25.2 vol adapter for 6S batterry pack , and 12,6vol adapter for 3S battery pack
@giorgioroascio84384 жыл бұрын
@@diylady Thanks for the information! You are fantastic, continue making videos, I will always follow you. Cheers!
@bucmeister77133 жыл бұрын
@@diylady Now I see, there is a comma in 12,6 volt whereas it should have been a period as in 12.6 volts. Now I see why this did not show how to build a 6 volt replacement pack.
@TheSpeakerGuy_Official4 жыл бұрын
Thanks, this video was very helpful as I recently was given 9 18650 battery's. What is the highest charging voltage you would recommend? I have a 12v 2a plug, should that be alright?
@jacquesb52482 жыл бұрын
if you link 3 together in series then 12.5 to 13.6....please using a proper bms and don't just connect 12V to it.
@thegoatcatcher2 жыл бұрын
Does the final outlet (black and yellow wires) account for charging and discharging? I see other BMS systems have a separate charge and discharge ports. I plan to use a 6s BMS to do a blue tooth speaker build with a 24 volt power supply. How many 18650 batteries should I use?
@diylady2 жыл бұрын
On 6S BMS will have an port for charging and one for discharge. You can use 6 or 12 batteries for this…
@bayuaria66662 жыл бұрын
Kenapa kepala charger saya panas banget? Kalo batre nya hanya hangat biasa
@electricchard84102 жыл бұрын
Can you make a video how to put battery indicator meter for level of charge and discharge? Thnk you✌️🙂
@xSO202 жыл бұрын
You cannot use BMS as a cell charger, you need a charging module.
@NoThingL0se4 жыл бұрын
Şiir gibi montaj olmuş helal olsun
@arjakegado45922 жыл бұрын
And can i use a 22 awg wire for wiring in battery and bms?
@jerrynguyen6853 жыл бұрын
You're awesome lady .Where are you from? Perhaps we can make a joint venture to develop a product for the US market.
@bio101554 жыл бұрын
This might be a silly observation, but can you confirm that what I am seeing is 3S2P configuration - two sets of (18650) in series and in parallel to up the capacity?
@joemo59293 жыл бұрын
Or good for drone builds
@hargiafancerezo5649 Жыл бұрын
Where to buy this kind of bms?
@migzryefranceczech77363 жыл бұрын
DIY lady how much mah in your 3S 2pack battery?
@tejasindani48984 жыл бұрын
I need a 9s bms can I make it by making 3*3s bms in series?
@prunaca4 жыл бұрын
Hi Lady, I have an old drill that worked with 14.4volts ni-cd pack. You think this pack is powerful enough to make it work with my drill?
@enginozkan72683 жыл бұрын
You should make 4S pack for 14,4 volt.
@MTAudioDIY5 жыл бұрын
Tốt lắm cô gái!
@diylady-jennyvan99165 жыл бұрын
thanks bạn đã động viên. hi
@hernanhernandez85623 жыл бұрын
Que cargador usas?
@jacksprat70874 жыл бұрын
Do you make up battery packs to sell? I need a 6v, 15Ah pack for charging with a 10 watt solar panel. I could put a buck converter on the end to get it down to 6v if necessary. Or, can you provide a circuit diagram for such? Thanks Mike
@diylady4 жыл бұрын
Sorry but i have not do it before , i’ll try it as soon as i can, and i’ll up it on my channel.
@jacksprat70874 жыл бұрын
This is for use on a game cameras. Almost all use 6v. I saw some LiFePo4 on eBay, 3.2v, 6500mAH. 6.4v would not hurt any game camera. 3600mAh will last 2 months in most game cameras. I leave mine unattended for like 6 months. I think if one diode protected each bank and regulated the solar panel to 6.4v you could run direct off the solar panel. 0.5 amp is the best a 10 watt panel will do in bright sun. I just subscribed!
@arjakegado45922 жыл бұрын
Sir it can be that 12.6v 25a battery pack into 12v DC 150 watts?
@jedunboxing41273 жыл бұрын
what model of battery is this?
@hasanalitonyali2 жыл бұрын
In the video, your spotlight video on batteries is in the foreground rather than the narration... You passed even the plus and minus connections of the batteries quickly.. Oh, you can share the connection photo or the plan.
@MdArafat-pi6qr Жыл бұрын
How to charging voltage your battery
@nareshassaithambi23903 жыл бұрын
12v motor how many hours it will run bro...
@Nosci10203 жыл бұрын
Input and ouput same wire? Charge on same wire?
@karraral-hadad95452 жыл бұрын
Yas
@experienciaonline36344 жыл бұрын
Please list of materials and where did you buy greetings from Mexico
@diylady4 жыл бұрын
i'm sorry but can you buy it from aliexpress ?
@manhthuy90643 жыл бұрын
pin nay chạy dc moto k bác để e thay vào moto quạt ạ
@bucmeister77133 жыл бұрын
Thought this was going to be how to build a 6vdc battery pack however it looks to be a 12 volt pack.
@celeron.263 жыл бұрын
12.6 volts dc not 6 volts dc
@jangarilaw6953 жыл бұрын
How many amps are there?
@viswanathanramakrishnan76132 жыл бұрын
Everything is fine; I request you to highlight the following: 1. How long the charger has to be connected with the battery pack? 2. Is there any indication about the battery is fully charged?. Please clarify. Video is nice one to be tried.
@gilsoncesarinvencoes3 жыл бұрын
👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼
@fxxxaxxx63593 жыл бұрын
how many amps are there???
@yobhebstv30213 жыл бұрын
How many hours charging battery ms lady
@vickisabella1303 жыл бұрын
Hello love you video do you have any video. Of building a 36 volt 12 amp. if you do please let me know or share this with me or if you have any diagram would help me to Bill mine would greatly appreciate it thank you very much
@marcoariston46543 жыл бұрын
Como eu ligo 6 celulas sem a placa BMS?
@kennyvelasquez41173 жыл бұрын
Buenas tardes, ayudaría mucho el diagrama del batería pack.
@suryakantaraychoudhary43664 жыл бұрын
Can I use 40 amps bms on my 20 amps battery pack?
@diylady4 жыл бұрын
Suryakantaraychoudhury Choudhury yês ofcourse you can
@Sahilshorff692 жыл бұрын
No
@Sahilshorff692 жыл бұрын
Thank you
@induvishwakarma89624 жыл бұрын
What's bms battery charging the 5v micro USB charger?
@induvishwakarma89624 жыл бұрын
Mai is bms battery ko 5v micro USB charger se charge kar sakta hu kya?
@thiphuongnguyen91235 жыл бұрын
😚👍😚👍
@marcodeguzman52993 жыл бұрын
How to know if the battery is fully charge
@hasifasip24983 жыл бұрын
How many A you battery?
@halima3488 Жыл бұрын
Sona
@hassimmohamed2167 Жыл бұрын
Give the details and required iteme
@mp1801703 жыл бұрын
Cut that bloody music 🎧😫 nice job though
@joziksk43234 жыл бұрын
If i use 6 batteries i Will have more capacity ? Because i making bluetooth speaker 2*100w and i dont know how many batteries i need to use for 5-6+ hours of play time please help me 🙏
@diylady4 жыл бұрын
You must use at least 9-12 batteries to pair 1 pack of 3S batteries
@joziksk43234 жыл бұрын
@@diylady and if i buy 6 batteries for 6s bms Board ?
@aubui77053 жыл бұрын
Cho giá bao nhieu 1cuc bin bạn làm đó bạn ơi
@diylady3 жыл бұрын
Mình chỉ làm dùng chứ k bán bạn ơi
@ceccoDJMUSIC4 жыл бұрын
please link pcb,tanks bye bye italy
@joziksk43234 жыл бұрын
Wait a minute this board is named 3s so you must use only 3 batteries ? Or ? If i do this like you i Will have better capacity ?
@diylady4 жыл бұрын
i use 3S with 2 pack battery ..
@joziksk43234 жыл бұрын
@@diylady if i do same like you i Will have better capacity ?
@Ramkitheone5 жыл бұрын
I made a charger out of 4 18650 batteries. Then used 4s 40A charging board from aliexpress and did the circuit as said. After leaving it to charge overnight i can see the charge has only come 11.1v where as i was expecting it to have 16.4v. Also the charge lasted for 5 mins only any reason why?
@diylady5 жыл бұрын
Oh. The first : you shoudn’t charge it over night , second : have you test your battery ? It’s new or that you take it from laptop battery ..? And the third : your charging is not work any more , it’s broken ...
@paramcanada75523 жыл бұрын
DIY Lady how do you know that the bettry is full or it needs charging ???
@stefanmerk57503 жыл бұрын
how do you charge this typ of BMS 3S2P?
@madinnovationandcreation56503 жыл бұрын
By using adaptor
@stefanmerk57503 жыл бұрын
@@madinnovationandcreation5650 please show me an example
@radutudortenis13 жыл бұрын
@@stefanmerk5750 This kind of BMS have included over charge protection, balancer, under voltage protection . Thats why you only need an 12v adapter charger.
@nafeesahmad39943 жыл бұрын
Charging power ratting share
@TuanLe-ty9ic5 жыл бұрын
like
@johnnyboy136424 жыл бұрын
Why are you using a 12v - 25A BMS for this pack? It's way too overkill for such a small pack.
@johannmeiring42083 жыл бұрын
Why do'nt you tell us what the amprage is that this BMS (BS) can handle ?
@radutudortenis13 жыл бұрын
It's write on the BMS pcb - 25A!!!
@andregrundler99615 жыл бұрын
Where can I find the thing can charge the battery??? Link please 😢😢😢
@culichilango80194 жыл бұрын
Do it yourself with a junk pc power suply (atx power supply), its veri easy, and you can get 3v, 5v, 12v, even 24 v from it. But for charging this bms you need a 12.6 v, so get an extra dc-dc up voltage, to increase the 12v to 12.6 v from your atx pc power supply modificated. Check some videos of how to transform a pc power supply for getting 12v (and others). Hoppe i help you.