How To Make a Brake Line With a Double Flare Tool - 2002 Ford F150 Rearward Copper Nickel Line

Рет қаралды 30,933

4 жыл бұрын

Double Flaring Tool I Used: amzn.to/36nscUz
Copper Nickel Brake Line: amzn.to/2QmyH4n
Brake Line Unions: amzn.to/2ZR9ZvX
Rigid Small Tubing Cutter: amzn.to/2ZMawiY
Steel File Set: amzn.to/2FjNV3Q
Bubble Flaring Tools: amzn.to/2twqLo1
Skip to 7:27 for how to make a double flare.
In this video I go over the process of diagnosing, removing, and replacing a ruptured and or rusted through brake line on my 2002 Ford F150. This process is mostly the same for many vehicles that have old rusty brake lines so it should be helpful for other cars and trucks out there as well.
Thank you for watching! You can support the channel at NO cost to you by using one of the above affiliate links. I hope we earned your subscription and that you found this to be helpful. I really appreciate your support.
Blessings from Minnesota,
Ben

Пікірлер: 21

@BryanChance 3 ай бұрын

Same thing just happened to me. The break is right at the mounting bracket. Thank you for sharing this video. Exactly what I needed.

@Ry77x 6 күн бұрын

Thank you. Great vid and almost exactly what I have to do in the morning. Never done this before but you’ve helped. And my son is going to help me as well

@AMentorway4u 4 жыл бұрын

Great video. Good job teaching the kids mechanical aptitude. You can never go wrong learning how things work and being able to get yourself out of a stranded situation.

@kenswitzer4133 4 жыл бұрын

I sure am glad I don’t live where salt is used in the winter. Great job on the video.👍🤙😃

@BenjaminSahlstrom 4 жыл бұрын

Haha I KNOW. Salt is horrible. Once I stopped at a salvage yard in Alabama and couldn't believe how clean the cars were underneath! They were like brand new!

@spelunkerd 4 жыл бұрын

Nice job. When Scotty Kilmer started teaching brake line repair, many learned the sloppy, illegal technique of compression fittings. With flares on both ends, and no compression ferrules, you're good. Probably worth replacing other lines soon, that short flexible length at the end should be easy to swap out.

@Eddy63 4 жыл бұрын

Another good vid benji ... Your little helper was good as well ...

@WBBClips Жыл бұрын

Appreciate the nice closeups.

@voolandashland2914 10 ай бұрын

you should do bleed again with the engine/car start. because sometimes pressure inside the master cylinder and brake lines are different during the engine start and during engine off.

@stevefletcher8157 Жыл бұрын

Good vid

@fredsmith7980 2 жыл бұрын

Thanks

@guillermocuevas3495 3 жыл бұрын

Hi Ben, do you have a video replacing the brake pads?

@marcusgilliland2529 11 ай бұрын

Great video, but a heads up ... from what I read, a bubble frare is not meant to be reusable or if reused, only as a temporary fix.

@king49334 4 жыл бұрын

Bracket trap corrosion stuff

@kenroc156 2 жыл бұрын

How do you put freon in roof top ac after I put on bullet piercing valve

@TheMax0005 Жыл бұрын

Would you recommend a mini bolt cutter to cut the brake line?

@rjwiderman 2 жыл бұрын

Pumping your brakes will bleed-out your reservoir ….so the best way to stop your vehicle is to first set your park brake. This presses your wheel brakes manually against the drum or disks. Then when you apply your brake pedal there is less distance to apply your brake. Try this going down hill.