This is a video on how to make a Carb Sync Tool out of basic materials from a Lowes or Home Depot 1. YARD STICK 2. 2 CYCLE OIL 3. 3/16" ID CLEAR TUBING 4. ZIP TIES 5. DRILL/DRILL BIT Camera used Canon PowerShot S110
Пікірлер: 20
@mikelongwith69223 ай бұрын
Thankyou
@alongwithposeidon2323 Жыл бұрын
Crazy how bad inflation is 4 years after this video was made. It cost you $7 to make this tool. I bought everything you bought. Same brands. All from Lowe's. And it cost me $21 as of November of 2022. I have my own drill, drill bit and zip ties.
@MrGilly3 жыл бұрын
this is really genius, thanks!
@MrGilly3 жыл бұрын
$10 beats buying a $100 kit just to do this job once in x years
@Alifreesoul9 ай бұрын
Thank you brother 🦾
@davidg57042 жыл бұрын
Thank you for video 🤙
@MIKESGARAGE8132 жыл бұрын
Thank you please subscribe
@mrquince326 жыл бұрын
Nice - how bout a radius at the bottom to prevent kinking ? JD
@tedturner52994 жыл бұрын
Fan freaking tastic, thank you.
@Headsup95505 жыл бұрын
Remind me to never loan you a drill bit! Drilling into the concrete.. SMH..
@kjadfhgioaudbfvilaeu5 жыл бұрын
Watch out for air bubbles. Any suggestions on how to get them out? I feel that if there are any bubbles in the oil then the accuracy of this already not accurate kludge, will reduce the level of the two sides that you're trying to align.
@MIKESGARAGE8135 жыл бұрын
kjadfhgioaudbfvilaeu I leave it overnight and it should work them out
@trevorteeter9614 жыл бұрын
Drink a beer, check the bubbles, rinse and repeat till you can’t see bubbles
@dasundilshan72653 жыл бұрын
This is not perfect because, When you start, the oil in this tube is drawn into the engine, is there no valve attached to it? Please tell, whats the story of them big puppys ...
@MIKESGARAGE8133 жыл бұрын
You have to have both sides connected. One to each carb. It’s not a perfect method. But it’s damn close.
@vstar71962 жыл бұрын
Even before I saw this stupid video, I made one of these. Absolutely ridiculous. You have to fill the tubing with engine oil because you will stuck the contents of the tube into the carbs. I saw one moron fill his U with colored water. I put hose clamps on the tubing close to the carbs, but no matter how careful, if the sync is way out the U will still empty into the bike. I built a two gauge manifold with ball valves instead. Works perfectly.
@ClatoTom4 жыл бұрын
Why the hell are you working on the floor. Don't you have a table? It makes everything a little easier. It doesn't matter whether one side of the oil is slightly higher than the other. You just have to make sure that the position does not change and does not go up and down.
@Jamesrealasdeath4 ай бұрын
Well you forgot to throw in a couple of cheap disposable 50 cent fuel filters from a small engine, that'll smooth out your bouncy s***.
@vstar71962 жыл бұрын
Even before I saw this stupid video, I made one of these. Absolutely ridiculous. You have to fill the tubing with engine oil because you will stuck the contents of the tube into the carbs. I saw one moron fill his U with colored water. I put hose clamps on the tubing close to the carbs, but no matter how careful, if the sync is way out the U will still empty into the bike. I built a two gauge manifold with ball valves instead. Works perfectly.
@t2tnt62 жыл бұрын
Do you have a video showing the one you built with the 2 gauge manifold with ball?