Carb Sync Tool: Making and Using

Рет қаралды 21,788

My home garage life

3 жыл бұрын

Making manometer and using it. Mig welding contact tips are cheap and easily avaible sync adapter's.

Пікірлер: 24

@briancash359 Жыл бұрын

The fluid is automatic transmission fluid. The adaptors are mig welding tips you get from welding supply. A lot of tool rental places have them.

@MTNMANWOODWRKS 10 ай бұрын

Where did you buy the tips? I can’t find m5 tips near me

@taxiarchisk.6031 8 ай бұрын

Nice helpfull understandable video

@kylesulaiman8581 6 күн бұрын

👍

@jasonadams74 Жыл бұрын

Couple of questions, first if I have 4 cyl, 4 carbs. Do I need to double this device? Secondly where do I plug in the M5 adaptor for my Suzuki GS1000? Thank you!!

@embededfabrication4482 Жыл бұрын

did u try it with water or does it just make a lot of vapor in the tube?

@worty Жыл бұрын

Am I right in saying this will work as a vacuum gauge rather than a simple, mechanical set up.

@myatkhant1876 Жыл бұрын

Can i use engine oil for liquid

@briancash359 Жыл бұрын

Look up making a manometer to see the 4 carb setup

@thedaydreamer7972 2 жыл бұрын

So in a dual carburated motorcycle, what is it on the carburator that you are turning or adjusting that is bringing those levels equal? the idle screw, the mixture screw? TY

@myhomegaragelife5607 2 жыл бұрын

It is linkage screw that is located between carburators. That sets the throttleplate opening between each other carburator.

@briancash359 Жыл бұрын

Should be able to get adapters from auto parts stores too.

@adolfomendoza248 4 ай бұрын

Very Nice, How do I make one for 4 carbs? you mentioned a couple "T" connectors, but how?

@rubaiz49 4 ай бұрын

kzfaq.info/get/bejne/rdiog7N4qrCucoE.htmlsi=CQYGYtQcLWhT0X-c

@throttletwstn9731 2 жыл бұрын

What size mig tip did you use

@myhomegaragelife5607 2 жыл бұрын

1.2mm inner hole tip's. M5 thread for honda and suzuki. M6 for yamaha.

@ManitouCat97 2 жыл бұрын

What liquid is that?? looks like transmision oil to me

@myhomegaragelife5607 2 жыл бұрын

I used Automatic transmission oil. two stroke oil works very well too.

@ramilramosgaming6745 Жыл бұрын

what's the alternative forATF fluid? can i use break fluid or oil fluid?

@Bezokay 9 ай бұрын

2 stroke oil incase it gets in the motor

@311kinsley 4 ай бұрын

Tgis is a JOKE!!! DO NOT ATTEMPT THIS!!!! I built the unit exactly how discribes and it sucked ATF (AUTOMATIC TRANSMISSION FLUID) into my motor!!! SO WHAT THE HELL DO I DO NOW THAT I HAVE ATF IN MY MOTOR!?!?

@tyshiz3381 3 ай бұрын

Lol your supposed to shut the bike off and adjust before it gets into your carb

@Peter-nu6ix 2 ай бұрын

@@tyshiz3381 The fuel filters, when you are actually watching the manometer, are intended to give you time to shut off the engine before getting the fluid into the cylinders. The carbs on your bike must have been way out for that to have happened. It could have occured if the adjustments were made too quickly or aggressively. Presumably, by now, you have resolved the problem of ATF in your motor. It will have done no more than cleaned out the compression and oil control rings in your motor. Now it will be running lopsided, you may have to run ATF through the other cylinder to ensure that you have cleaned them both out (caution about hydraulic lock). If you have, indeed, "built the (manometer) unit exactly how --discribes-- described", you will not have done any harm to your bike and may have actually improved its condition. That is the reason for using ATF fluid, which acts as a solvent, or 2 stroke oil. Neither of these products will harm the engine of themselves. The only problem may occur if the engine has not been shut off in time to prevent what is known as "hydraulic lock" which can damage your engine.

@wadenvern 4 күн бұрын

@@Peter-nu6ix what happens if you get hydraulic lock? I also built one, but had to shut my bike off before the flluid got sucked into the carbs...will that cause Hydraulic lock? I think i have to make my hoses longer is maybe the problem...