pretty great now I have to make a trip to home depot try using c-clamps and clamp it on the table.
@MattsFishingAdventures4 жыл бұрын
Yes sir it definitely works and its budget
@johnbuschman8815 Жыл бұрын
Good job I like it
@yangjianhunt5 жыл бұрын
Nice design, Matt!
@MattsFishingAdventures5 жыл бұрын
Thanks were you able to understand the setup? Video was kinda ehh lol. Messed up a little and fixed it up on the editing.
@yangjianhunt5 жыл бұрын
@@MattsFishingAdventures Yep I definitely got the idea. :)
@redladyfish42015 жыл бұрын
Awesome idea, very handy.tight lines!
@alfonsom23854 жыл бұрын
Video was unclear i now have a pet shark in my room
@mrBDeye3 жыл бұрын
Items needed for this project...You'll need one pencil and one brother to hold the pencil.
@octyl953 жыл бұрын
Quick tip maybe you should buy a Dewalt or Milwaukee drill see you had some problems at 2:30
@50shadesofblue244 жыл бұрын
Great video bud!
@americanpatriot6615 жыл бұрын
Gr8 idea! getting ready to spool up some reels myself. Good luck on the sailfish trip bro can't wait to watch the video.
@bigbamboo9363 жыл бұрын
Dread, the inner nuts were not necessary. Due to your washers you could adjust the tension just from the outer nuts. Other than that, not bad.
@JCS1956AZ3 жыл бұрын
You could make that a quick release/quick load if you cut the tops of the holes open, so all you had to is loosen the nuts and lift out the whole shaft and reel. Or did someone already suggest that?
@MattsFishingAdventures3 жыл бұрын
That's a good idea 💡
@Nick_Tag3 жыл бұрын
Master at work :) was the mistake basically to use two nuts on the right side as well?
@MattsFishingAdventures3 жыл бұрын
Don't think it was much of mistake. I've had that same spooler for a couple of years and I still use it and ill let you know that it spools braid so tight how its suppose to be put on and I'm super impressed with how everything works.
@larrytwiner3 жыл бұрын
Yes, I believe that is what he changed. The washer was causing the single nut to spin with it, but with the second nut locking in the first nut it won't move with the washer. At least that is what I got out of it.
@equinoxfishingteam58374 жыл бұрын
Great job Dude!!!! Congratulations from Equinox Fishing Team....
@piercedwyer50404 жыл бұрын
mate get some good tools
@charlesmurray1220 Жыл бұрын
Challenged.
@williamster2015 Жыл бұрын
You could have done this much easier by literally doing 50% of this build, Image it as the letter "L". Two washer, spacer and locking nut on the exterior side and interior side. Followed by a flange washer then your string, another flange washer, , a flat washer, your spring another flat washer and a Locking wingnut or a cwibg nut backed with another nut
@brentnanita39393 жыл бұрын
I dont mind a shop fee if they would do a professional job. Most guys they have doing it do a crap job. I dont trust them to do my braid, esp tie my knot on the spool.
@zachshott78334 жыл бұрын
You actually have to PUSH when trying to drive a screw....
@robertrook27143 жыл бұрын
You have officially lost your man cardb
@ShutUpNFish17 ай бұрын
Dude! This was horrible….get you some better tools too!😂