I was so impressed by the first video in the series that I decided to go through the whole playlist, one by one. I learned so many useful tips in 2 videos. Thank you for sharing

Hi Trev nice videos its great to see some one who is old school I have been in this trade for over 40 years now good luck in every thing you do..

Absolutely great channel for anyone looking for help with sheet metal or body repair advice and techniques 👍

Steely cracked me up with his health and safety message. Absolute quality!

Your van looks better than I expected when you started cutting apart panels in the last episode...

13:42 perfect and easy solution. I salute you sir

Brilliant stuff Trev.your attention to detail is unbelievable 👏

Trev, you explain things so easily and I really enjoy watching your channel

I am just getting into metal fabrication and this channel is exactly what I need! Looks like there is quite a bit for me to catch up on too. Think I will put the kettle on and hit that PLAY ALL button :) Well done Trev, great work.

I tried to fix some rust on my rx8 today. 1mm sheet metal and a brand new mig. NEW FOUND RESPECT FOR YOU!

Awesome, as always! Thanks for showing us how to do these tips and tricks!

Buenos dias .maestro grsacias por poner estos vidios .soy Colombiano pero vivo a qui Barcelona España exelente lo que hases crak

Amazing! Thanx very much. I've found this video right in time for a piece of my Fiat Cinquecento Sporting I'm restoring at the moment.

Trev you are a true craftsman! Keep up the great work here bud!

I've seen a lot of different people making different tools and things. I have to say, I'm really impressed with your ideas. I know I'll end up using them in the shop. That dimple press design can be used for many different things. Great job and thanks again

Really informative and simply explained, thank you very much! Lots of motivation for me now 👍🏻

Great video. I’ve been doing this stuff on the hobbiest level now for over twenty years and yet I’m always learning something new from you! Thank you Trev!

Mint video this one, you Sir are a scholar and a gentleman

I love the press tool idea. Great video, clear and precise explanations and results presented in such a way that I want to have a do a making a press tool just to see if I can copy what you did! You are a top man Trev!

Thoroughly enjoy Your helpful videos Trev ..Thank You for sharing Your skills .

Very cool techniques. I'm going to try some of them. Thanks for the video.

BRILLIANT information and technical advice.great blogs

Superb job on your press! Also, amazing job on your little motorcycle! Very creative, for sure!

I've learned a lot more from watching your videos. Welding with my everlast welder has gotten much better.

20 seconds in and I am totally subscribing and also hitting that 👍👍

Wonderful a true Professional ! Thanks for sharing ! Wonderful Lambrettas as well ! The hair style ,I thought Rocker ,but no Trev's a Mod. Keep up the great work

Thanks Trev Can wait to try out my newly found knowledge.

Those lambrettas are awesome! I had a series one and series two and a jet200 back in the day 😁. Love the channel. Been learning a lot from you to do metal work on my bugeye sprite. Thanks.

That was awesome tool design for speed clip dimple. Nice and easy concept too.

Nice craftsmanship. It looks just like original.

G'day Trev, loving these tips! I recently watched all the van build to date and now gone to these tips. I'm not sure what the process is to put them in a play list, but it would be much easier to watch them and possibly find them. currently i go to "your videos" and have to hover the mouse pointer over the description to see #2 etc, because the title is long and it only shows part of it, i think on the mobile phone i'd have trouble finding the next one. i'm very impressed with how you have explained the tools and how each process works. i didn't even think to clean the copper up, as i thought the process was to stop the mig wire doing porcupines on the back side mostly, but understand the function well after you started the weld on the copper before joining the headlight piece. looking forward to getting through to the current "tips" episode Cheers, Dean.

some brilliant tips, thanks trev

many good tips here. The dimple press idea is just what I need for a project in the works. Thank you

Really like your technique of rounding the corners of your patch panels. Certainly takes more time than a straight cut, but no corners!

You a very good teacher, I be happy to find you. LG Michl 🐗 💨

Ingenuity and resourcefulness is plainly seen

Fantastic video, can't get enough

A good preservative oil is "LPS 3". A bit pricey, but it is a paraffin base aerosol spray and will protect bare steel tools for years. It is suitable for machined and polished crankshaft throws as well. I use it sparingly and will substitute ATF (auto trans fluid) for things that I will use again in less than a year's time. A little wipe-down with ATF will last much much longer than WD-40 and it's as cheap as dirt. I LOVE those little Lambrettas! I just discovered your channel today... nice work! Subscribed & notified!

Great info in this Trev. Appreciate you sharing!

love the channel trev! in the bodyshop trade but learning so much that i will be making some tools when i get the chance cheers mate

loving your videos

Nice work Trev thanks for the video great tips

Great video, learned more in 20 minutes than 20x1 hour videos.

This is BRILLIANT! Thanks!

Hi, nice Videos with great tips, I love this little scooter its look like my old Lamberta 150 I had when I was young.

Trev great as always that sqaure dimple press is amazing on the copper on hole filling i always do it backwards were I can copper in front weld from the back if possible less finishing work on the panel

great video....watched it a while ago, but great to watch again....clever tool and love the little 'Vespa'

Very nice work, and a lot of good tips. Thx a lot m8

Thanks very much Trev.

Clever tool, brilliant video cheers

Thank you again Trev.

I Like the press, It's nice when something works as planned 😊 I might try making a similar press for creating drain holes in cills i need to replace on the van 👍

That turned out great

Thanks trev great videos

Great skills, thanks for sharing.

Great protips bro!

Brilliant tooling!!

Thanks for putting that on. I will need one for my landrover bulkhead. Only two holes but will be a great help cheers.

Awesome. Top work!!

Очень полезные видео у вас , доже сплохим знанием языка всё понятно. Спасибо

Very nicely done, on all accounts.

That's just as good as a fly press would have done, brilliant tool making

Great little press, id better make one . I know ill be needing it one day .

Very handy little tool.

would if I could... You are very Talented !

This is great Trev! I love your accent. ;)

Bodywork "fever"given to you by Trev.The music of same name -"Fever"written by Eddie Cooley. Originally performed by Eddie Cooley and The Dimples in 1956. Just a bit of Do Wop trivia for those into that genre. Best to you and yours

A job well done.

Wow:) sweet press tool!

Wicked press tools loved the first one. Ya wee dancer. Would off been my words Exalant teacher 👍 👍 👍 🏴󠁧󠁢󠁳󠁣󠁴󠁿😜✌️ Chears for sharing 👍👍👍

Amazing stuff

Great tips, thank you.

would i love to work under your supervision totally awesome a real fabricator NOT A PANEL REPLACER another great video

thank you for your video's

Awesome!

Good tips, just another one, get an old style copper headed soldering iron, with a long handle, to reach way up behind panels to weld up holes.

love that copper trick

Well done.

man, your sooo good

Top job. Can vouch for the copper heat sink on panels.

Hey up Trev, love the channel. I only found it last week and love the build too. I've just started welding and found your tips very helpful so keep them coming. Are you on Instagram, and what's the engine noise from on the intro lol?

Some prestretch on the work piece will help with any distortion but it worked well. Guys do that prior to rolling beads with a jenny as well. I expect you know this but maybe it will help someone. Enjoyed the video.

Clever Trevor ...

Yes this is the toll I was speaking about in your urchfab parody video.

Dude, you've got to be proud of those juicy welds. Peace

I wish I'd found your channel before I'd started butchering my car!

Super nice tool

Damn good!

i appreciated the copper for filling a hole , thats one where be it i dont do alot welding of this type but when i do i hope to remember that tip, stupid easy and worth its weight in gold or ummm copper

almost getting flashbacks watching these vids: lambretta-quadrophenia-the who, music at the end-the munsters- eddie munsters car, the lorry-ian dury-"itinerant child"..and so on...and so on..

thumbs up!

Love your blogs Trev is your Handel on the tool you made a Morris minor bumper iron ?? Looks like one keep up the good work Trev

Hey!! Like your videos and add to fb list, sow Just im say hellow from chile 😋

Shit to a blanket!! 🤣 thanks for keeping your channel pg rated

Jeez, Vauxhall went all out on the expenses when they specced those Grills...

" I'm really impressed with that!"...............So was the steel!

Nice work, however, I would like to see you press the areas you did. Is there any more video on that?

What tools and grit do you use to grind your welds?

Trev, The old screwdriver trick..... Metal forming: The constant in metal forming is material volume. Material has to go some where when the inside radius is formed. It's either going to fold over on itself (getting thicker) or shrink (getting thicker). In either case volume of material remains the same. I bet if you measured lip thickness in the radius it would be ~1.2mm. Have you addressed the question of material quality and or specification? Do you purchase a specific grade of steel?

Trev, Would love to see how you make those lambretta scooters models