How to make a stirling engine

Рет қаралды 593,518

2 жыл бұрын

I tried to make a Stirling engine as simple as possible, but it was still difficult. Stirling engines are not easy to make.
List of materials:
- candy drops tin (00:03)
- piece of thin aluminum sheet (00:16, 10:12, 14:22)
- thin aluminum bar (01:58)
- cyanoacrylate glue (02:07, 06:20, 13:00)
- steel wool (02:25)
- silicone rubber (03:39, 20:58)
- 32mm tube (05:16, 06:16)
- two strips of galvanized steel (or copper, or brass) (07:10)
- solder tin (07:24)
- thin malleable steel bar (or wire) (08:08)
- pencil (12:06)
- small balloon (13:34)
- bolt, two nuts and two washers (14:15)
- electrical connector (17:00)
- two large lids (19:17)
- masking tape (19:38)
- lubricating oil (21:32)
Tools:
drill, drill bits, scissors, pliers, screwdriver, soldering iron, sandpaper, hand saw, pocket knife, pin, marking pen.

Пікірлер: 202

@boomstick4054 Жыл бұрын

This is probably the most likely successful stirling engine build you could attempt from KZfaq videos. No words spoken or numbers to deal with, just good, plain physical instructions.

@avcomth Жыл бұрын

Just watch this one also, far superior build kzfaq.info/get/bejne/e62qdNyWsMuycmw.html

@cslloyd1 Жыл бұрын

Imagine trying to make an internal combustion engine in your kitchen. Zero chance of that. Its incredible how imprecise a Stirling engine can be and it will still operate.

@call_me_mado5987 Жыл бұрын

I mean at it's core it's pretty simple

@1islam1 Жыл бұрын

@@call_me_mado5987 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

@CRuM770 Жыл бұрын

@@call_me_mado5987 so is an internal combustion engine, but much tougher to make on your kitchen with garbage and simple tools.

@call_me_mado5987 Жыл бұрын

@@CRuM770 Yeah, in theory it's simple. In practice?, it's never simple. Engines are very complex there are a wide variety of them, some simpler than others and some more complex

@CRuM770 Жыл бұрын

@@call_me_mado5987 agreed, but the same applies to sterling engines. I saw a 10 cylinder unit with electronic timing control. I have also seen a one cylinder gas engine with mechanical valve and spark timing. It was about as simple as the engine in this video. Very interesting engine, it didn't spark on every revolution so the rpms would fluctuate. If I recall, it was for a compressor.

@benperkins1555 8 ай бұрын

The "graphite lubricated sleeve" is a stroke of genius! Thanks!

@sriharianne5229 4 ай бұрын

All ideas are so simple that I can make it for my grand son. Thanks a lot for the video mu friend. Thank you.

@alexplotnikov2658 2 ай бұрын

Не сделаешь и работать не будет.

@3pipper Жыл бұрын

Bravo… excellent, well presented and for myself I feel it was done in a manner any language could understand… thank you indeed, much appreciated!!!

@growleym504 Жыл бұрын

Good vid. It hopefully accomplishes two things. First, inspire others to get started tinkering with Stirling engines. Second, to dispel the myth of current state of the art DIY Stirlings accomplishing any useful work for any practical power input level. A whole new paradigm is needed to make them practical as prime movers. Even when the input energy is "free" (solar heat, ground or evaporative cooling, etc) the cost of implementation and the replacement of moving parts make a small diesel engine look pretty good. That has got to change, and only the DIY hobby community can afford to "waste" the time and resources for the R&D required. A hobbyist has got to start somewhere. Part of finding out what works is finding all the things that do not work. Being able to construct a running heat engine in a half hour out of mostly just trash is a good foot in the door. Your design is simple enough for a reasonably smart 12 year old to follow, and it will teach him a little bit about the Stirling cycle.

@marcbutler8896 Жыл бұрын

This got me building.....

@21stCPH 7 ай бұрын

Well stated

@sergeyshyshkov2483 2 ай бұрын

Чудова наочна демонстрація геніальності в простоті.Здається давні винахідники невиправдано ускладнювали свої конструкції,що іноді збивало їх з інженерно правильного шляху. ДУЖЕ ДОБРЕ,МАЙСТРЕ!

@adanealemayehu5903 Жыл бұрын

the is really really incredible i was strugling to understand the stirling engine now you just made it clear to me i thank you from the bottom of my heart

@adanealemayehu5903 Жыл бұрын

@alexanderwardrope9352 what I'm trying to say is that this video helped me to understand Stirling engine

@valterleao2798 Жыл бұрын

Adorei, simplesmente fantástico 👍❤️ Abraço aqui do Brasil 🇧🇷

@christiangirodet7606 10 ай бұрын

Combustion externe amigo !

@Ritefita Жыл бұрын

the most easy to make I ever seen. the beautiest (the cleanest) too. well done!

@marcbutler8896 Жыл бұрын

Gonna build one right now.... got everything needed. Thanks. When you put the ice on top I finally realised how it works. Magic!

@Alin-bz3go 3 ай бұрын

Have you done it?

@marcbutler8896 3 ай бұрын

@@Alin-bz3go I did. I had forgotten about it. It worked

@alexplotnikov2658 2 ай бұрын

@@marcbutler8896 не ври. Это не будет работать.

@the-real-random-person 11 ай бұрын

One of the best tutorials out on youtube!! Thanks man!

@cleidsonaraujopeixoto163 2 жыл бұрын

Já cheguei deixando o like, o Mestre Foguista merece!

@user-on1ib5ot6o Ай бұрын

ТАК НАГЛЯДНО И ОЧЕНЬ ПОНЯТНО, НЕТ СЛОВ, ЭТО САМАЯ ПРОСТАЯ ДЕМОНСТРАЦИЯ, Я ДУМАЮ ТЕПЕРЬ МНОГИЕ С ОГУТ ЭТО ПОВТОРИТЬ, СПАСИБО АВТОРУ

@mikeconnery4652 Жыл бұрын

Great build and you have a lot great comments from around the world. Keep improving and keep up the videos.

@nedstar7378 2 жыл бұрын

Excellent video, thanks for sharing.

@aparecidomiranda1191 2 жыл бұрын

Ótimo vídeo Parabéns muito bom isso 👍

@danielmierop662 Жыл бұрын

You tube just recommended your channel to me. I really like your creativity!👨🏻‍🌾😋

@SBJCREATORS 2 жыл бұрын

Excellent video project sharing like it ☺️

@dougmorgan6616 Жыл бұрын

Clever design. Nice use of found materials.

@eversonrodrigo5979 2 жыл бұрын

Muito bom o seu trabalho.

@LeoLeoJR 5 ай бұрын

Very minimalistic, yet very informative.

@samina7670 Жыл бұрын

i think the can you chose was too small in height, the air not expanding enough to cool down on its own. That rubber balloon as an air mixer is brilliant.. can't wait to attempt and make one myself.

@TheCompleteGuitarist Жыл бұрын

I thought the same about the size of the tin, but a longer tin would probably require more energy.

@samina7670 Жыл бұрын

@@TheCompleteGuitarist Also applies to all videos i watched about Stirling engine... The piston only move up/down depending on the crank shaft. most they make it not long enough to allow a cooling phase. Hot/Cold differential can increase efficiency of the engine. I wish i had space in my apartment to craft something to show all what i mean.

@dvdvdvfvvffcvfvfffcreccecr1039 Жыл бұрын

@@samina7670 i am looking to make this and i definately will have it longer

@arduinomaquinas Жыл бұрын

Nice, ❤very good project🇧🇷😉👍👏👏👏👏👏

@fanievisser8628 11 ай бұрын

Wow!!Amazing.Always want one but cant afford.Going to surely build my own. You are a very clever man to thought of this.The baloon and steel wool is an wonderful idea. Great ingeneering solutions. If one take how large the fly wheel it was actually moving quite fast!!! I LOVE IT I LOVE IT.!!! Awesome man!!

@canastasiou68 2 жыл бұрын

That was a fun little project, i like Sterling engines. Thanks for sharing. 😀

@mattparker9726 2 жыл бұрын

22:51 some things I see that could be improved, first your flywheel is well off balance, and second I think there is some lateral play in the main crank, maybe add some spacers where the screw is?

@call_me_mado5987 Жыл бұрын

The guy is making an engine out of stuff he found in his home, i think he did pretty for that

@hamjudo Жыл бұрын

I've taught physics at summer camps. Students are motivated when they make a device that works better than the example that the teacher made. This design is excellent for teaching _because_ there are so many opportunities to improve it.

@C.A.D.D 2 жыл бұрын

always a brilliant work!

@spiritualawakenings6251 7 ай бұрын

These are fun. I made mine from sterling silver because of silvers amazing heat transfer properties.

@LeoLeoJR 5 ай бұрын

Try to use gold. It's even better.

@spiritualawakenings6251 5 ай бұрын

@@LeoLeoJR You must not know much about conductivity.

@luizcarlosdasilva8436 9 ай бұрын

Pior que funciona 😂 Muito bacana 👏👏👏

@luizazevedo9706 Жыл бұрын

Parabéns. Hoje entendi como funciona.

@JustFun-iz9rf Жыл бұрын

Impressive nice job 👍🏼

@MuhammadAli-ih7qs Жыл бұрын

Outstanding and simple

@ratosecotoxico Жыл бұрын

The most beautiful motor ever see. Sir entender

@YooProjects 2 жыл бұрын

So unique project. Y are super talente my friend 👍💫💪

@dwimarpinnock9799 8 ай бұрын

Wow just simply amazing 👏

@matinsakr6548 Жыл бұрын

Nice work.thanks

@martyjames6204 Жыл бұрын

genius design!!

@ymmitjones7904 Жыл бұрын

That was awesome.. I Enjoyed just listening to it run.. haha Good Job

@eric81872 2 жыл бұрын

Thank you for the video!😜👍♥

@haripappu2281 Жыл бұрын

Epdium ne pana Mata ...ethuku da loose😂🤩

@filipedesouza6885 2 жыл бұрын

caraca, a tesoura do maluco cortar tudo. rs que idéia genial, será que se colocar duas latas, uma do lado da outra, fica mais potente?

@ka_okai9 9 ай бұрын

Bravo my guy, what a beautiful video❤

@keupondestroy911 2 жыл бұрын

Merci beaucoup pour la vidéo

@benoregan4623 4 ай бұрын

Great video!! Would it work better if you cut some holes in the displacer disc to let more air flow through the steel wool?

@joeybouten2726 7 ай бұрын

made his but added a counter weight and a 10lb flywheel and after a few minutes of spinning to get in started it finally worked!.....and by worked i mean it ended up working too well with the heavy fly and the comparatively super lightweight parts that it literally tore itself apart after 30 secs of running. AMAZING! i love this will recreate!

@samuelfellows6923 Жыл бұрын

17:09 ~ 😬⚠️, just undo the screws to remove the metal block from those electrical screw terminal blocks, no need to cut open with a knife and risk cutting your hand

@yuriysemenikhin302 Жыл бұрын

The simplest video I've seen so far 👍 Will be perfect fit for working on my project that I described in the video Solar to electricity 24/7 in Your back garden Videos like this make other projects so much better 🙂

@angiefav1847 10 ай бұрын

Very nice very impressed thank you

@brettsfishingdiaries 7 ай бұрын

coolest thing ive ever seen

@eastkyphotos 7 ай бұрын

Very good! Simple!

@skyridersrc3644 4 ай бұрын

I did not understand that nut bolt technique is there any go through hole?

@bhargave6088 5 ай бұрын

This 25 min was worth in my life

@rondunnett7204 7 ай бұрын

Well Done Sir!

@mkepler5861 Жыл бұрын

thank you!!!

@itamaroliveira2791 2 жыл бұрын

Seus vídeos são da hora ! ..Mas os que eu mais gosto são os de mini armas .., isso tem haver com o seu canal ! .É like também

@iamomi993 Жыл бұрын

What can i replace the steel wool with? I dont have strel wool can i use steel scrub instead?

@kdub1953 11 ай бұрын

Brilliant!..... one for the grandkids during the summer school break I think!😊

@davidliz315 Жыл бұрын

Superb

@m.l.6704 Жыл бұрын

sweet !!!

@adamw8469 Жыл бұрын

Incredible

@kadurim 3 ай бұрын

Impressive! Why is the part with the baloon segment and its connection to crank shaft needed?

@kadurim 3 ай бұрын

How do the ice cubes help?

@acejohnting7497 Жыл бұрын

may I ask the length for the galvanized steel?

@elanofigueiredo2893 Жыл бұрын

Fantastic

@LalbalochBaloch-eg8rl 8 ай бұрын

Nice

@user-kn6or8hi3r 6 ай бұрын

ممتاز استمر contunius

@fayezelmazaty488 11 ай бұрын

ما مدى الاستفاده منه حاليا فى هذا العصر والكهرباء؟ برجاء الرد للعلم /مع الشكر

@Carrot_attacker88 3 ай бұрын

Not used much at all, my grandad has one that powers a lightbulb and charges batteries (slowly) using focused sunlight

@monkuslum 3 ай бұрын

Can someone tell how to make the crankshaft exactly and if the weight of the flywheel matters?

@alanspring8462 10 ай бұрын

Happy to subscribe

@MikeAlano Жыл бұрын

play at 2x speed...save time. good project :)

@carlosgeoprojetos Жыл бұрын

Poderia trazer o famoso fogão a diesel? Obrigado!

@mohammedraoofullah2235 Жыл бұрын

Funtastic engine

@user-nn1of4gf7k 11 ай бұрын

what is the grey thing he rols on the rod

@EnordAreven 2 ай бұрын

Can sponge be used instead of tin wire?

@Lechoslowianin 2 жыл бұрын

👍 👍

@saitamaspunchkim4148 Жыл бұрын

Im a final year electrical engineering student..I imagine going straight infront of the panel with an opening statement "I'm going to show you how to charge your phone only using a candle" ...b4 introducing this starling engine and a dynamo connected to it🔥🔥🔥😂....do y you think it'll be great for my project..I think it'll be great 🤷‍♂️😎💯

@user-jf4jg6ry6s 11 ай бұрын

Good good good 👍

@aliviamacpherson8945 6 ай бұрын

nice . now do this oil burner blue flame ..flue with copper 5mm coiled inside of the flue with two outlets at bottom to run to 5 gal drum with water pump hot water.all sealed. run this off to v8 sterling engine ro refurbed motors to provide elec?

@user-gp9kb7tv3u Жыл бұрын

احسنت برافوووو

@sputnik873 2 күн бұрын

why is the steel wool necessary?

@tsarodavid9730 8 ай бұрын

Interesting

@christiangirodet7606 10 ай бұрын

Bonjour ! Ce moteur est â combustion externe il me semble ! Un ancien professeur de mécanique de la vieille école ! Salutations sincères.

@michasowik2438 2 жыл бұрын

High end YT content.

@Amid_Karantin 6 ай бұрын

I advise you to turn on the 2x speed

@botanikworld Ай бұрын

👍

@marsstarlink3235 Жыл бұрын

Would love if you make one a little more bigger/elaborate with a USB charger.

@Eduvasquet1022 Жыл бұрын

La..base..para..hacer . máquinarias....de.todo.tipo. el.ingenio ..humano.. tecnologías..modernas....ya se viaja.ala.luna... y aún en..desarrollo....bien

@villagevlogwithsaqib4531 2 жыл бұрын

How to work this engine

@RICH_BGMO 11 ай бұрын

❤

@NonrevS Жыл бұрын

Very good, no horrible music, irritating faces and voices. As expected, a few comments from the engine wizards out there at no it all ltd.

@shayanliyan8293 8 ай бұрын

what's that wool like thing

@Carrot_attacker88 3 ай бұрын

Steel wool

@tethsovnn6186 2 жыл бұрын

♥♥♥♥♥♥

@mateci328 6 ай бұрын

3:34 que pegamento es????

@awsibly971 4 ай бұрын

💚❤💚

@nelj3376 Жыл бұрын

Welcome to 500N Sub! 🌹❤✋👍

@Slumerican2407 10 ай бұрын

Maybe if you use a better heat source it will work better

@charleshudner4149 10 ай бұрын

Já tentou fazer um fogareiro a gasolina para esse motor?

@olivierklepper2960 Жыл бұрын

The steel wool adds quite some weight to the piston. Couldn't you glue it to the top of the cylinder instead, for the same effect?

@nigelwilliams7920 10 ай бұрын

The steel wool acts as a recuperator as the air passes from the lower to the upper cylinder and back. So the air has to pass through it, that's why its on the piston.

@Puper22 Жыл бұрын

Steam ?

@georgesuzima4388 11 ай бұрын

C'est quoi le nom de la matière qui est dans la boîte ?

@LLDJ_ 11 ай бұрын

Mint bon bons

@wolframgerber7118 2 ай бұрын

Es ist feine Stahlwolle.

@boomstick4054 Жыл бұрын

The question is, why hasn’t a car or kart ever been built that operates on the stirling principle? It could even have electric coils for the heat source.

@pa_maj.MARTINI-van-MAN Жыл бұрын

Check out...Man builds 100mpg engine using 200-year-old technology.

@boomstick4054 Жыл бұрын

@@pa_maj.MARTINI-van-MAN Check this out! kzfaq.info/get/bejne/gciees-Uts-wYZc.html

@boomstick4054 Жыл бұрын

@@pa_maj.MARTINI-van-MAN it appears that it’s already been accomplished, just not on the market as the video seems to imply?

@pa_maj.MARTINI-van-MAN Жыл бұрын

@@boomstick4054 True, and many times great ideas/inventions end up being deliberately put on the backburner. The energy companies love taking our money no mater what they say. Record profits while we all suffer.

@boomstick4054 Жыл бұрын

@@pa_maj.MARTINI-van-MAN 75 horsepower, no oil changes because it runs so clean. Burns diesel or gasoline cleanly, cool exhaust. No muffler. Only 1 spark plug to ignite the burner. These engines that NASA developed & tested in airforce base vehicles/taxis are the answer. They aren’t high performance engines, but would be great just for a normal drive. 15-55 mph roads