Thanks for watching Francesco

i thought dry ice would be better,,

Thank you very much!

hank you

hi, Thank you for watching

I agree 150% preferably in english speaking countrys, feel FREE to like share and sub, thanks 4 watching

thanks for watching Justin

Thanks for watching Mario

Thank you! Cheers!

thank you my friend !!

Not quite ready for prime time as yet but I"m hoping to make exactly what you are looking for,, see here > kzfaq.info/get/bejne/e9Bio6abnpvbqo0.html Thanks 4 watch N ;-)

Thanks 4 watching

yes, but no propper parts yet, just what I had on hand, see here kzfaq.info/get/bejne/e9Bio6abnpvbqo0.html stirling engine with dc generator.

Thanks for the visit and the comment Luis

Rat Rod ;-)

you welcome, questions? feel free, thanks for watching

Thank you for watching

YES, THANX

Thanks for watching Leo

Watch here kzfaq.info/get/bejne/Zt9yaKiL07zeqZc.html for ideas to build a stirling engine from stuff you probly have lating around. You can do it!

@@ROCKNTV1 no, you make stirlings. Shoa is talking about Sterlings

thanks 4 watching

You mean never? Becuz that's me.

the plan was to use a freznel lens, and run the engine upside down using solar, Thanks for watching

thank you ;-)

fire cement, but it shrinks

there was no coal used in this video

K

thank you sir for watching. Over the several years building these engine a few hard facts have become evident, 1 is being rebuildable quickly and cheaply due to the fact that the colaberation of materials you see here are "repurposed" and for the most part, "in testing". A failure of any may come down to a change in material and not a redesign of a part. At this point I can say i am totaly happy to report that the welded steel pipe nipple power cylinder kzfaq.info/get/bejne/fcqKnruenaqldJc.html and a light weight cast iron piston work great, and if propperly machined and fit are relitivly cheap. I could go on for hours about my findings but must leave that for a book or video I can explain my self better. As far as generating electricity from this, I am leaning toward a non magnetic fly wheel made of composits and impregnated rare earth as in the type used in wind turbines. I have also come to understand much about the actual thermal deltas needed to make power and the fluid dynamic propperties inherant in the diferrent designes of stirling engines, ie alpha, beta, gamma. Thanks again for watching, feel free to peruse my play list page for my engine videos, a thumbs up and a sub greatly appreciated. john

slow running temp delta 150f / best running temp D 200/300f so cold end < 120f , hot end >300/450f ,, thanks for watching

tHOSE NUMBERS ARE EXPLAINED IN THE VIDEO

I watched this video could not see dimensions.is it the same as your beer can motor displacer 61/4" bore x 2 1/2. power piston 2"bore X 2" stroke displacer pistons is a lot bigger is that more efficient? Did you wrap the fibre glass bat material in aluminium foil?

hellow sir, I honestly could not sell this engine, I could not recover my cost,lol but becuase it is realy at this point not mechanicly friendly. By this i mean, sombody other than myself would need machine tools such as a lathe and a mill to make and repair any parts. Not to mention a knowledge of how these stirling engine ought to run. Every bit of te stirling engine shown here is a comprimise of some sort, with variables ranging from the materials i had on hand, and those i was prepared to make. I hope to at some point in the future be able to provide an engine similar to this with a standardised parts list that equates to an approximate power out put. thanks for watching. john

@@ROCKNTV1 yeah no problem I understand. I meant if you built a 2nd one, I did see another youtuber sell large ones but was crzy expensive. I've never built one before so I'm a little nervous. I've got a dremel & some jbweld, no mill thou. Thnx for the detailed reply. I'll make a small one, but wont nearly be as good or powerful as yours 😉 take care

good luck n stay tuned, the engine i hope to produce will last longer than me. Here, if intrestead, kzfaq.info/get/bejne/pZOdZKV2pt7MdKM.html is another engine i made that wont wear out during my life. This is a sort of build progression of videos that ought to inspire yah. thanks for watching

thankss

Ya know, I have been thinkng alot about that lately,,,, When this engine was concieved,,, in my head, it was suposed to run upside down in my pool, guess i should say "in reveres", from solar. But my testing of hot end collectors, in direct, non focused sunlight was only 140-160f . I have severa 3x4" freznel lens that were tested to be perfectly suficiant, how ever very dangerous if not aimed and mounted with some ridgitity. Not easy with wind and water to contend with, ie floating.

@@ROCKNTV1 simplify for me

@@potatohamlin5242 When I first started building these engine, I was and still am of the mindset that bigger is bettter. However here> kzfaq.info/get/bejne/q5OJmbN2q6jMZ2Q.html < I began to run into what i can only surmise is a compression ratio anomoly. I acctualy had the engine explode several times befor I dreamed up the tie bars that hold the hot/ cold half together. This began when i machined a very close fitting power piston and increasing the tempurature delta 800f/65f. The flywheel was NOT heavy enough to make the compresion stroke untill i increased the temp of the cold side. All of this said means IMHO that there are an infinate amount of variables to makeing useable power from these engines as there are builders.

@@ROCKNTV1 still have no idea what the hell ur talking about

thanks for watching Martin ;-)

In NH not far from the dragstrip Thanks 4 watch N ;-)

No brob , K.B. port! I live at the Epping circle my self once . Just after Mc'y D's. 👍☘️👍

Yessah, Kenny Bunk, We used to joke during my baseball years,,, didnt matter where we were playing,,, get up to bat, point over the fence and yell Kenny Bunk port, crowd went wild. ;-)

yes

thanks for watching

thank you for watching and noticing ;-}

because youtube does a poor job with english, and honestly not worth my time to fix their errors, or some one else who's first language is not english, then I have to spend more time translating to check, sorry, just a guess, you dont live in the usa ?

@@ROCKNTV1 I live in Poland. You know where is it?

yes, north of germany, and you write very good english, I hope i explaind myself just trying to be honest. I have made 200 videos in the last 18mo with 10% USA traffic, strange when you consider i speak english and live north of boston yet YT doesnt show them here ?

I just cheched and YT is auto generating these, can you see them?

oh yes,, right

yeah, in my defence it is winter in my garage, You can take solice in the fact of knowing in the summer i run commando ;-)