How To Make Force FeedBack Gaming Steering Wheel

No video

How To Make Force FeedBack Gaming Steering Wheel | Arduino

Рет қаралды 67,148

ZUDU MaLLi

Күн бұрын

Пікірлер: 305

@zudumalli 5 ай бұрын

TIP YOU NEED TO KNOW! if you making DIY Gaming Steering Wheel (Important). Be sure to watch. kzfaq.info/get/bejne/bauJZKqhpq20k58.htmlsi=PEOsDiciiBHmt72X

@Muzankibutsuji74 23 күн бұрын

Can we use a ebike motor

@sarigamasongbox584 11 ай бұрын

Waiting for next video.❤️😋.this is the best video ❤.from 🇱🇰 😊

@zudumalli 11 ай бұрын

🥰🥰

@Jawo_o 5 ай бұрын

NINTENDO HIRE THIS MAN

@zilcard959 11 ай бұрын

this is what all i need formerly, thanks bro, you so helpful for me

@zudumalli 11 ай бұрын

Glad to hear that! thans man

@lumivision. 9 ай бұрын

Hi, I'm planning to make the same steering wheel, but I have a couple of questions: 1) If you buy a gearbox and handbrake that connect via USB, will they work together with this steering wheel? (I’m also going to make the pedals myself). 2) I don’t particularly understand electronics, but I want to put 2 motors in this steering wheel, can you tell me how to connect 2 motors? 3) I am going to power this steering wheel using a computer power supply, but in your diagram I don’t understand how to connect it to the board, can you help me with this? I hope that you will answer my questions and I want to say that your homemade product is very cool!!!

@zudumalli 9 ай бұрын

1.) Yes you can use multiple devices. it's ok. 2.) If connecting two motors you have two options. First, you can connect both motors in parallel to the same BTS7960 motor driver. 2nd you can use two BTS7960 motor drivers and provide separate power to the two motors. 3.) Yes, what do you not understand? Thank you!!

@AkramDehqonov 8 ай бұрын

@@lumivision. i think the motor driver will share the power of single motor to two motors

@ishanattudawa0098 5 ай бұрын

maram koliti me video ekat patta😀👍

@zudumalli 5 ай бұрын

❤❤

@ishanattudawa0098 5 ай бұрын

@@zudumalli 👍

@mohamedzewail8907 10 ай бұрын

Great video, all the other ones lack the details in yours, thank you so much, you helped me a lot.

@zudumalli 10 ай бұрын

You're very welcome!

@familykitchen6161 5 ай бұрын

bro you are amazing and fantastic, i love your concept and videos but plz also provide parts links that you use in video. because out there are lot of same product that dont work same. Thank you man. i appreciate your work. and also how much total cost for only wheel in this video if i use everything you use.

@zudumalli 5 ай бұрын

I bought a lot of parts from our local market (Sri Lanka) and online market prices are very different so that's why I didn't upload the links. And I randomly calculated from Aliexpress it is close to 50$ USD.

@Perkperformansparth Жыл бұрын

amazing work bro 💖also voise is lovely 😁

@zudumalli Жыл бұрын

Thanks 😅

@anuhaskalpa Жыл бұрын

Gammak mcn ❤🔥

@zudumalli Жыл бұрын

😍

@user-fg7ot2rx1l 7 ай бұрын

Hi, I wanted to know if I can find any steering wheels for cheap instead of making it with cardboard

@devampatel1265 10 ай бұрын

Hey, I had a doubt, if I am using an arduino Leonardo instead of a controller’s board can I use 5 analog inputs (steering, gas, brake, hand brake, clutch) because the arduino has 6 analog inputs available right ?

@zudumalli 10 ай бұрын

No bro, the Arduino has six analogs, but the software supports only four analogs.

@James01709 7 ай бұрын

You can use emc utility

@JeffRenko 5 ай бұрын

@@zudumallifour? Then you can use clutch brake acc and handbrake?

@gl1tch286 4 ай бұрын

@@JeffRenkothen the steering

@RzzClips 7 ай бұрын

can this wheel play on asetto corsa? does 3/8 inch Aluminium tube fit enough?

@zudumalli 6 ай бұрын

Yes. Yes its enough.

@mechatronicsgenius3655 10 ай бұрын

I made too feed back steering Simulation 🎉 with Arduino Leonardo

@zudumalli 10 ай бұрын

Very good!

@katogergo4710 8 ай бұрын

Hi, why is this build do not works with other arduinos? I am planning to build something similar, and collecting ideas. I plan to do it with something stronger than an arduino, maybe an ARM. Or maybe the pc program can only use arduino leonardo?

@zudumalli 8 ай бұрын

We use wheelconfig software to use this. This software supports only arduino leanardo. But I have seen some people make it from other program boards. But I don't really know much about it.

@katogergo4710 8 ай бұрын

@@zudumalli okay thanks for the answer, i am gonna do a little bit more research

@sheetos_5518 6 ай бұрын

Bro you can use a board like Arduino but have more performance called stm 32 They usually use it in direct wheel drive project search about it it would be more helpful❤@@katogergo4710

@K.C.O Жыл бұрын

Major improvement, does this work for console?

@zudumalli Жыл бұрын

No😐

@brownie2875 5 ай бұрын

why we can't use arduino uno, i have uno can we able to make without ffb. any idea

@bossoy0769 5 ай бұрын

Bro i tried Uno at First Too i tried it with Uno joy and Encoder but no its not working you cant Upload the Firmware for the Software rfr Wheel configuration on the uno because it has a different Chip so it isnt possible and you have no Force Feedback wich means you have no center spring or degree lock for example 900 degree lock wont work so not worth it buy Leonardo instead

@brownie2875 5 ай бұрын

@@bossoy0769 got it thanks buddy

@gl1tch286 4 ай бұрын

U can make a wheel without ffb with uno but it is not that good

@brownie2875 4 ай бұрын

@@gl1tch286 with uno r1 right?

@GamingHour000 5 сағат бұрын

I don't have almost zero knowledge about boards can i use Arduino Leonardo R3 board

@rexycontemplates Ай бұрын

I'm curious why the wiring is different from the 'Tech at Home's DIY steering tutorial. Maybe that's for EMC, yours is for AI WAVE?

@zudumalli Ай бұрын

Wiring is different due to firmware

@premsontakke2298 9 ай бұрын

Which software are you using, and does it support steam games like f1. If possible, can you explain how ardunio is connected to pc to detect it as a gamepad. Mostly software side of the build. Thanks 😊

@zudumalli 9 ай бұрын

It does not require any software. The wheelconfig software will automatically detect the game.

@risingstarstudios 6 ай бұрын

How many rpm, should be these dc motor (I want to choose rs775)?

@zudumalli 6 ай бұрын

RPM doesn't much matter, you need large torque. if you don't understand watch this video kzfaq.info/get/bejne/bauJZKqhpq20k58.htmlsi=93VRqvpIQERDKRAl

@israeljmtd1667 11 ай бұрын

hello my friend one question here does the motor handle the resistance fighting with your hand? I'm worrying it my burnet out, how many current does it draw on load have u checked? and also I have seen ur diagram sheet (pictures) and I have seen u used 7 buttons connected with H-shifter, can the be used simultaneously or when u use the buttons u don't use the H-shifter? how does it work really? and I cant wait till u put out hand brake with controller and how to be able to play forza horizon 5, tnx for the video keep it up, well explained

@zudumalli 11 ай бұрын

1. Yes, it is one motor, but when the FFB power is used at 100%, it feels like too much powerful. So I use about 60% most of the time. It also depends on the game. 2. No I did not measure the current. But after playing a game for half an hour and doing a temperature test, the maximum is about 52°C. No problem now. 3. Yes, the buttons are not used when using the h shifter. 4. Will upload a video about it soon.

@levinhquang2285 2 ай бұрын

I used to use wheel config before and when I applied 12volt power and my hand got hurt because the wheel was continuously spinning

@zudumalli 2 ай бұрын

kzfaq.info/get/bejne/ep53jMaDv7bSj4k.htmlsi=NQCE8w9Y7zDb_JYm

@roketcraft2856 4 ай бұрын

when i say i like metal 0:30

@Ix_Meru 8 ай бұрын

Will this work with h shifter, pedals, and handbrake

@zudumalli 8 ай бұрын

yes

@_Smoke_V_Okno_ Ай бұрын

is it possible to use a DC motor type 550 at 14.4 volts?

@zudumalli Ай бұрын

Yes you can but the torque is quite low

@_Smoke_V_Okno_ Ай бұрын

@@zudumalli So I'd better order a new motor. thank you for responding to comments even after such a long time))

@matioxs3132 Күн бұрын

Hello, I have a question, if I only have a 12v DC motor, can it only work with a 12v power supply or can it also work with a 24v one and if possible, which one would you recommend?

@zudumalli 17 сағат бұрын

it's depending on the manufacturer. Google your motor type and find the maximum voltage it can provide.

@SteigerX921 8 ай бұрын

Hello, I'm going to make a same steering wheel like yours, but a have some questions 1 if i changed all the pulley with smaller size: 10mm bore 60 teeth to 40 teeth, 10mm bore 20 teeth to 16 teeth does cause any problem ? 2 my wheel will have 2 motor, can you tell me how to connect more fans ? 3 Can you tell me how to connect the wheel with the aluminium tube ? I hope that you will reply the answer

@zudumalli 8 ай бұрын

1. 20 teeth + 60 teeth ratio is = 1 : 3 16 teeth + 40 teeth ratio is = 1 : 2.5 The 3 and 2.5 ratios were slightly different here but it's not a problem. but *remember* if the pulley ratio was little the motor needed more energy to rotate. and at this moment the motor gets more heat. 2. you can connect directly your 12v supply 3. you can use this part for it. its call ''linear Rod Rail Shaft Support''

@AbdullohQodirov2021 7 ай бұрын

Brother I have a question, would it be the same process even with settings if i use arduino uno but not arduino leonardo? Btw, the video is🔥

@algodude8713 7 ай бұрын

The Arduino Uno is not able to appear as a USB input device to a computer, so unless you wanted to do significant modifications to the programming, you will need a Leonardo

@Timakazarinov 7 ай бұрын

На uno можно делать но это очень сложно,надо будет переписать весь код и написать свой

@zudumalli 7 ай бұрын

No, this coding is made for arduino leonardo board. Therefore, the coding cannot be uploaded to other arduino boards

@Ryangozzlink 8 ай бұрын

Thanks a lot bro goodjob🙌♥️ But i have some questions . Is this 900deg wheel?? And a watch some videos creating this wheel but with STM32F401CCU6 board and says this is better than arduino is that true? And is possible to make this with STM32F401CCU6?

@zudumalli 8 ай бұрын

Yes, it supports a max of 2160 degrees of wheel rotation. I actually don't know about that.

@Ryangozzlink 8 ай бұрын

@@zudumalli thank you♥️

@RavinduLakshan-yu5sc 10 ай бұрын

Supiriyak boza me wage ekak enakan balan idiye🥺🖤

@zudumalli 10 ай бұрын

❤❤

@utok3411 3 ай бұрын

I have a question, why would you need to connect a resistor from the postive terminal to channel 1 and 2 of the rotary encoder?

@zudumalli 3 ай бұрын

this project uses an "NPN open collector output type" encoder so we have to use ''INPUT_PULLUP'' inputs or ''external pull-up'' resistors. that's why I am using 10k resistors. Basically, if we don't use resistors, the wheel is completely not working

@Jack-n5i 2 ай бұрын

hello there are multiple versions of the dc motor that you showed, so i wanted to know how many newtonmeters of torque you reccomended, is 1 enough or do i need more?

@zudumalli 2 ай бұрын

One motor is enough for me. It depends on the size of the pulley and steering wheel you are using. But I also install another motor in the future.

@Harmansnation Ай бұрын

When I am connecting button and I press it. My wheel Center messes up and rotary encoder isn’t working for a while. What can I do?

@zudumalli Ай бұрын

check your wiring maybe there is a short circuit

@Harmansnation Ай бұрын

@@zudumalli hey I checked it. But when I use the wheel rotary encoder isn’t stable? The center moves tiny bit every time i use the wheel

@fawadalisoomro1158 19 күн бұрын

Bro plz tell me the best arduino model for making ffb stearing while gear box and and clutch brake and acceleration best model

@zudumalli 19 күн бұрын

This firmware only supports to arduino Leonardo board only.

@fawadalisoomro1158 18 күн бұрын

@@zudumalliarduino uno is no the best for making iy

@duarteandradeabreu7511 7 ай бұрын

how to do the paddle shifters??????

@vansanglam5230 3 ай бұрын

Let me ask you, the steering wheel turns on bt but turning to the right is ok but to the left the steering wheel runs full speed. The effort of locking it to prevent it from rotating is a failure, isn't it? I hope you can help me

@zudumalli 3 ай бұрын

make sure the wheel config command mode is ( PWM +/- ) or reset all settings to default

@AnimePhilippines 5 ай бұрын

Can i use this without ffb? Just like you make in your joystick? Im planning to swap the joystick to this Arduino

@zudumalli 5 ай бұрын

yes you can

@AnimePhilippines 5 ай бұрын

@@zudumalli ok thanks

@vitalii7282 2 ай бұрын

Hi, Have a problem) With this program in port 10 is always served 5v and motor always work in max, what could be, won't you tell me? Thank you in advance)

@zudumalli 2 ай бұрын

in the wheel config software have you not selected the command mode as PWM +/- ?

@vitalii7282 2 ай бұрын

@@zudumalli no, selected PWM+Dir

@RaceDriverMIKU 8 ай бұрын

Plz BLDC motor next time, and DD wheel DIY.

@joseitod0553 4 ай бұрын

Hello bro, I was looking at the diagram and pins 7 and 8 are not connected. Could two more buttons be connected there? And assign them in the program? Since they are not being used and I would like to place more buttons for other actions

@zudumalli 4 ай бұрын

no you can use A3, A4, A5 (analog side)

@joseitod0553 4 ай бұрын

@@zudumalli I installed the buttons on Pins A, but they did not work, instead I installed them on Pins 7,8 and 9 and managed to obtain more actions with three more buttons

@saimazahid2095 4 ай бұрын

Can i use a power supply of 12v 5amp because I am using only steering and gas and brake along with ffb ( I don't need Padal shifter or h shifter )😊and can i use a laptop adapter of 12v without power supply

@CheeseLocalll 4 ай бұрын

nope you need 15 amps because it will not work loss of power due to its short trravel

@zudumalli 4 ай бұрын

no, you can't. @BlUMILEEDITS is right. btw you can use 24v 5amp adapter.

@bossoy0769 4 ай бұрын

@@zudumalli can we use 24v power supply with only one motor without any worries?

@ca5ualm3dia 7 ай бұрын

ok but how do you add buttons for shifting? I dont need paddles but some might want them. can it play on xbox series s forza or is it pc only ?

@zudumalli 6 ай бұрын

Analog pin of arduino board is used for shifters. I will show about that later. It is the PC Microsoft Store version that can be played.

@RajatKumar-qs2im 9 күн бұрын

Can it be made to use with PS4?

@juanbautistakala5171 2 ай бұрын

Hello! Excellent job. I'm trying to replicate it but I ran into a problem. I have an EPSON SERIES L Printer encoder and I don't know how to connect it with your diagram. Could you tell me how? Thank you!. Pd: If you could give me another way to contact you, I could send you images of the encoder.

@vitalii7282 2 ай бұрын

still actual problem?

@juanbautistakala5171 2 ай бұрын

@@vitalii7282yessss! It is 😢😢

@AnimePhilippines 5 ай бұрын

How do i fix mine when i rotate my encoder its move slightly then go back to its original state its not rotating its just keep coming back to the center I tried it to my uno and enter a code to read the rotation and it was ok but not in my Leonardo Hope you can help me

@zudumalli 4 ай бұрын

Have you checked if the z-toggle switch is working?

@pioma60 Жыл бұрын

funciona con el Arduino UNO?

@zudumalli Жыл бұрын

@pioma60 Жыл бұрын

😢@@zudumalli

@yagamingx2002 13 күн бұрын

Bro what's tha name of sticker paper you use . ??

@zudumalli 12 күн бұрын

It's a car wrap sticker. I don't know what the name is.

@TseleHub 5 ай бұрын

can i skip the belts and make it direct drive? what i lose if i make it direct drive?

@zudumalli 5 ай бұрын

You lose the torque. Watch my last video I explained this

@Shabib_Edits 7 ай бұрын

if i want to use two 775 motor in parallel, how many Volt and Amp smps should i buy?

@zudumalli 7 ай бұрын

you can use 24V 2.7A (65W) power supply

@JeffRenko 4 ай бұрын

bro in my steering wheel i used 12v 20 amp SMPS and i think its too powerful and the ffb is too stronge and breaks my wheel so s there any way to lower the torque and speed also i am using emc utility lite

@zudumalli 4 ай бұрын

I haven't tried emc yet

@kaeganphilips-mt3le Ай бұрын

hi bro i have made this but ffb is not working the motor keeps spinning or not spning at all please help

@zudumalli Ай бұрын

watch this - kzfaq.info/get/bejne/ep53jMaDv7bSj4k.htmlsi=Jns1PXutZd5uqMnt

@pablorojas658 4 ай бұрын

Hi! I can connect encoder direct un Arduino Leonardo? (I dont need pedals and shifter because i have External interface for this) I want only steear AND ffb

@zudumalli 4 ай бұрын

Yes, you can

@bossoy0769 3 ай бұрын

So could i have more power with 2 dc Motors one 775 and the other one 550 motor?

@zudumalli 3 ай бұрын

Yes, no problem

@jpn234 3 ай бұрын

Did you have another motor burn out after installing the fan?

@zudumalli 3 ай бұрын

@yashdeshmukh828 3 ай бұрын

Can you please provide the dimensions and all for the wood

@zudumalli 3 ай бұрын

the description has a diagram link all the documents are here

@atxu3837 Ай бұрын

bro i did the same but the belt slips when i use 25% gain how to fix that

@zudumalli Ай бұрын

Tight much as you can or install a belt tensioner

@user-fg7ot2rx1l 7 ай бұрын

Hey, I’m worried about using a dc motor… is it not going to result into a short circuit

@zudumalli 6 ай бұрын

No, that will not happen

@user-fe9tu9sg9o 7 ай бұрын

Did you use any software to use this in gta V of forza and how does the sterring wheel comes in 0 degrees did you setup that.

@zudumalli 7 ай бұрын

I have uploaded a video on how to play Forza and GTA v

@yunuss4766 3 ай бұрын

i already have a steering wheel i just want to add force feedback to it is it possible?

@zudumalli 3 ай бұрын

yes you can use Arduino and rebuild it

@venomgaming3290 3 ай бұрын

can i use a 3 phase rotary encoder???? if yes how

@zudumalli 2 ай бұрын

no bro this supports only 2 phase encoders

@thefakejou_ 2 ай бұрын

I hope you can see my comment. I want to know the rpm of your 775 motor because I can buy 2 variations (one with 1800rpm and one lower rpm).

@zudumalli 2 ай бұрын

775 motor has an RPM between 12,000 - 15,000

@thefakejou_ 2 ай бұрын

@@zudumalli thanks

@Thenameislucent 6 ай бұрын

Is there any way I can connnect the wheel to my switch consol?

@zudumalli 5 ай бұрын

In this way, a box can be prepared and connected easily. kzfaq.info/get/bejne/f893gbCnltncmmw.htmlsi=r5qsw5iYMDT0w2tb

@_Smoke_V_Okno_ Ай бұрын

can I apply 14-15 volts to the motor driver board

@zudumalli Ай бұрын

It can use up to 27v

@_Smoke_V_Okno_ Ай бұрын

@@zudumalli thank you very much, I will also collect it when the encoder arrives

@brownie2875 5 ай бұрын

bro can we use copy or clone arduino leonardo.

@bossoy0769 5 ай бұрын

Yes I have a Clone Aswell it just needs the atmega32u4 Chip

@brownie2875 5 ай бұрын

@@bossoy0769 thanks bro

@user-fe9tu9sg9o 7 ай бұрын

did you code the Arduino?? . thank for the video but i was thinking that do we have to code the Arduino if yes could you please give the code

@zudumalli 7 ай бұрын

No, I'm installing the Firmware

@blacksiderpro 7 ай бұрын

Bro can you do a vedio with multi-turn potential meter because i dont have huge amount of money please reply or tell me the steps

@zudumalli 7 ай бұрын

Yes, I am thinking of explaining how to make this with less money

@blacksiderpro 7 ай бұрын

@@zudumalli please do it very fast my boy 🥺🙏.thanks for replying. hatts off🥲

@user-sb2vl2lv7d 11 ай бұрын

hello, is it possible to connect the ffb to the vibration output on the gamepad and will it work?

@zudumalli 11 ай бұрын

I'm not sure. I will try and tell you

@user-sb2vl2lv7d 11 ай бұрын

Thank you I'll be waiting

@user-yt2tg5hm3n 25 күн бұрын

Can i swich the h shifter ground to above one?

@zudumalli 23 күн бұрын

yes

@user-yt2tg5hm3n 23 күн бұрын

How it detected in PC? Like gamepad in controler device or its like usb? I mean if it detected like gamepad in device manager i can callibrate it

@santoshym694 9 ай бұрын

Broo can we use db9 connectors instead of rj45 connectors

@zudumalli 9 ай бұрын

yes of course

@pavletrnic1433 10 ай бұрын

hello friend, is it possible to use a 4:1 pulley ratio to the encoder to improve acuracy?

@zudumalli 10 ай бұрын

Yes can, but you need to calculate the correct encoder PPR value

@pavletrnic1433 10 ай бұрын

@@zudumalli so i would put in 2400ppr if i had a 600ppr encoder?

@zudumalli 10 ай бұрын

Yes you are right

@user-JAFAR_1 3 ай бұрын

Hello can i apply that for the pxn v9

@zudumalli 2 ай бұрын

the software? - I actually don't know but if you have the wheel you can try it

@yashpaliwal4399 11 ай бұрын

Bhaii next video kb tak upload krdoge 😅

@zudumalli 11 ай бұрын

I think you are asking when the next video will be uploaded. mmm maybe next year🙃

@user-lg7nz8bl1i 4 ай бұрын

can we use 1000ppr rotatory encoder? if yes then changes we should do

@zudumalli 4 ай бұрын

Yes you can. Nothing changes

@user-lg7nz8bl1i 4 ай бұрын

Thanks man

@danishap900 8 ай бұрын

Where i can place the power supply? (Not pc power supply)

@zudumalli 8 ай бұрын

I use it separately. If you want, make the wheel base a little bigger and place it inside.

@jdmisbetter 8 ай бұрын

Can I use a multi-turn potentiometer instead of an encoder?

@zudumalli 8 ай бұрын

yes can, but it's working the same as a normal potentiometer. and no ffb

@AxtrodoSulfur 7 ай бұрын

so for potentiometer there is no ffb? @@zudumalli

@tgshreyas8702 10 ай бұрын

Please give idea bro Iam working hard for it

@bossoy0769 2 ай бұрын

Bro wich power supply Are you using ? 12v or 24?

@zudumalli 2 ай бұрын

12v but I will buy 24v in future

@bossoy0769 2 ай бұрын

@@zudumallihow much amperage does your power supply have?

@yagamingx2002 Жыл бұрын

Hello bro please make the video upload program in Arduino board

@JAAT_aujla07 8 ай бұрын

Bro from where you are Can you make it for me under budget 3k

@zudumalli 8 ай бұрын

I am from Sri Lanka. I will explain how to do it on a low budget in the future

@starrocks_ 4 ай бұрын

Is it possible to play mudrunner/snowrunner?

@zudumalli 4 ай бұрын

yes

@starrocks_ 4 ай бұрын

@@zudumalli can you make a video on that

@danevanex 4 ай бұрын

can't i use arduino mega 2560 pro instead of leonardo?? if so, where can I get the firmware?

@JeffRenko 4 ай бұрын

the firmware is made for the leonardos chip so you cant use that

@zudumalli 4 ай бұрын

firmware for Leonardo. cant use other

@tgshreyas8702 10 ай бұрын

60 teeth pulley is enough to rotate??

@zudumalli 10 ай бұрын

enough, The higher the number of teeth, the better

@editricks7552 4 ай бұрын

bro where did you buy arduino leonardo , for how much? (price)

@zudumalli 4 ай бұрын

I bought it from our local market (sri lanka ).

@louvretseng 5 ай бұрын

Will the diy steering wheel work on Nintendo switch

@zudumalli 5 ай бұрын

I don't know about that

@xynigz3410 26 күн бұрын

Can I use Arduino UNO instead of Leonardo?

@zudumalli 23 күн бұрын

@AceBLOX938 8 ай бұрын

how to mske the steering wheel only looks good

@zudumalli 8 ай бұрын

If you have the right tools, you can make the wheel look good

@duarteandradeabreu7511 7 ай бұрын

the steering wheel on ps4????

@DProGamingYt 22 күн бұрын

Hi, how much cable do i need?

@zudumalli 21 күн бұрын

20-25 jumper wires and 16-way ribbon wire (enough for wheelbase only)

@CINEARSH Ай бұрын

What is the torque figure can anyone tell me with 1 motor

@zudumalli Ай бұрын

This motor has 0.2N.M

@GanniGamingPL 7 ай бұрын

Can i use potentiometer or it must be encoder

@zudumalli 7 ай бұрын

Next video

@JAAT_aujla07 8 ай бұрын

Bro what is the size of wood you use in this built

@zudumalli 7 ай бұрын

0.75 inch

@Tej-oo6mp 5 ай бұрын

U can use a 24 volt big motor as it’s big and does not heat easily 😂

@bossoy0769 5 ай бұрын

You know this motor in the video Supports up to 24v too right?😂 but yes i get what u mean a e bike motor would be better but aslong as this motor works its good but yes you Need to cool it well

@Tej-oo6mp 5 ай бұрын

@@bossoy0769 thanks bro

@thejuviswam860 Ай бұрын

I am using rs755 motor now its not working the light in power supply keeps blinking when motor starts to work iam using 12v 10a supply can any one identify the problem

@DarkRange-vw2pn Ай бұрын

You Need a better Power supply 10a isnt enough get 15 or 20

@DarkRange-vw2pn Ай бұрын

I can Even explain Why, the Most 775 Motors use 12-15a as starting current so you Need atleast a 15a power supply to get it working 👍

@thejuviswam860 Ай бұрын

@@DarkRange-vw2pn it was working good so far but it got heat up and then the motor stopped working

@zudumalli Ай бұрын

Once your power supply heats up, it will stop producing power (10A is not enough for this) and try once using less power like 30-50%

@thejuviswam860 Ай бұрын

@@zudumalli actually the motor is heating up and stops

@thejuviswam860 4 ай бұрын

Bro what is the use of z switch

@zudumalli 4 ай бұрын

To turn on the encoder. In some cases it has to be turned off for calibration.

@makhilpranav6949 Ай бұрын

bro where to buy gears in online

@zudumalli Ай бұрын

aliexpress

@JeffRenko 5 ай бұрын

Bro what shop you buy parts from some parts I cant find help I am in colombo

@zudumalli 5 ай бұрын

Some parts are purchased from Nugegoda Tronic lk. The encoder purchased from aliexpress.

@JeffRenko 5 ай бұрын

@@zudumalli thanks i got my encoder from there it was only 3500rs

@himeshweththasinghe3118 Ай бұрын

hi i wanted to know if your firmware works on the stm32 board

@zudumalli Ай бұрын

@jzayden 11 ай бұрын

May I know so far what games does it work with, does it work with Gran Turismo?

@zudumalli 11 ай бұрын

Sorry, I don't know if this game works

@jzayden 11 ай бұрын

@@zudumalli Ooo thanks 👍

@astropanda0951 9 ай бұрын

what was the total price because i really want to make it, looks sick

@zudumalli 9 ай бұрын

actually, I can't tell the cost because our currency is different. parts' name in the description you can find it yourself.