Thanks brother for your comment. Let me illuminate one point. Until 60 percent sodium hydroxide solution has no considerable effect on copper 👍

I was going to highlight the same point: aluminum dissolves in caustic soda generating gaseous hydrogen and oxygen. They are highly flammable and even explosive. Perhaps it would be possible to use them through a burning valve. In the case of a larger scale, of course.

Could the solution be contained separate from the chemical? Have tab at the bottom that breaks the seal? Flooding the chamber when your read to use it? To extend battery life.

This will be like a sealed pudding can pull the tab, it's filled in! He separated container straight to the bottom.

i wondered this and thought would lead be better

Thank you so much 🙏

Thanks

No problem

you could use a baking soda/water mix and clean off the aluminum oxide with some gentle scrubbing before reusing. hope this helps!

Something I've tried that actually seems to work is to rinse the anode with vinegar. It stops the reaction of alkali on the anode. But it must dry completely or be rinsed with water before refilling with electrolyte or else it neutralizes the electrolyte. It does preserve the aluminum.

@@evanriddle1614 I imagine that the vinegar has to sit on it for a while, right? i would think you would need to scrub at least a little, and since the aluminum in this example is so thick i'm not against scrubbing a bit for it to work at full capacity.

@zatnicatienth just contact with the KOH or NaOH neutralizes it. Baking soda is for acid. Vinegar is for alkaline. The vinegar has to dry completely or be flushed out with water. The aluminum can be used again and again. I got 10 hours out of about 2 Sq cm .025" thick for a total of 1.5 ah. 2 hours one day, 5 hours the next day and the rest was consumed in 3 hours final day. About 150 mA

Can you charge the battery

Thanks brother.

You’re welcome ☺️

Better to use lead instead aluminium pipe. Because electrolite solution will spoil the aluminium. Electrolite don't have negative effect on lead.

@@jamalfuzail4369 you miss a point. That’s not the case. It’s something different you said.

Thanks brother

Not only that but also l have a lot of great ideas and projects. But l am very busy for some personal issues for the time being. I will make videos about those projects soon. Thanks for your comment.

@@joyofelectronics9782 that's awesome I'll stay tuned...just take care of life first. Also when you get the time since I'm no expert take a peek at a palygorskite clay + indigo blue dye mixture. ✌🏾

@@elkanahprivate7954 sure. Take care yourself too.

The electrolyte is an instant charge there is no charging needed this is the beauty...also yes you can series and parralel n step up or down too any volts you require

Yes you can make a larger one to get more current. I had two holes to position the aluminum more easily and neatly.

I also wondered why the 2 holes? It was a fair enough question, also a pretty good answer, cheers.

That’s Right but you can’t use the same electrolyte for a long time. You need to use new one bro👍

@@joyofelectronics9782 how long can it last if in use for at least 6 hours daily? Does it matter if not poured out when not in use?

@@nnejiamaechi9385 yes it is need to be poured out. And using 6 hours a day you can use it for about four years if your aluminum is thick enough 👍

@@joyofelectronics9782 Ok. To me it does not matter if I does not last dat long by using it 6hrs a day and did not pouring it out. What I would prefer to do is to change it whenever the electrolyte is weak and it can be determined by the reduced voltage.

​@@joyofelectronics9782can you use an automated spray system too keep the electrolyte topped up rather than a soak n toss method...its just a part off my ideas you seem too be on the same thinking as me but yh like a small solar powered electrolyte sprayer that sprays once every 10 minutes forever would that solve this issue maybe with an arundu board and a mechanical trigger off some description...cheers..get back too me if want too bounce ideas

It will work but not as long as the same lifespan.

Thanks a lot bro you are right about what you said👍

No it’s not rechargeable but reusable

great thanks dear sir@@joyofelectronics9782

Sağol kardeşim

Yes 👍

@@joyofelectronics9782 can you please tell how did you make Compound paste with Activated charcoal and Graphite, and the Binder.

Excellent 👍

In this video l told everything in detail: kzfaq.info/get/bejne/mtdnp6qQl8rQl2Q.htmlsi=rd7_p7-evo2NYP8H

Sağol kardeşim bilgi için deneyip sonuçlara bakacağım. Güzel bir çalışma olursa videosunu yaparım. 👍teşekkürler tekrardan.

@@joyofelectronics9782 kardeşim deneme imkanın oldumu acaba? eğer hidroklorik asit kullanmak istemezseniz alüminyum klorürde suda çözünüyor. onu deneseniz çok memnun olurum. birde bakırın yüzeyine sürdüğünüz iletkenin direnç değeri nedir? son olarak yapım videosu varmı acaba?

@@ozgurkaygisiz1562 kardeşim bu aralar o kadar yoğunum ki bu işlere inan ayıracak vaktim olmuyor. En kısa zamanda deneyeceğim ama.

@@joyofelectronics9782 teşekkürler sonucu yorum olarak paylaşırmısınız kolaylıklar dilerim

Not both of them. I mean with a normal use the aluminum will deplete after five years. If you use very rarely you can use maybe ten years in storage.

​@@joyofelectronics97827:22 Good. Meaning it's not rechargable? What is the Amp? If the size is increased will produce more volts and amps? Can this size run a DC fan or motor ..small size?

@@nnejiamaechi9385 this size of the battery can provide up to 1 amp. l measured and showed in the video anyway. The voltage will be the same when you enlarge the size of the battery but the current will increase. If you want to increase the voltage you can make more than one of this batteries and put them in series (2 batteries = 2.8 volts, 3 batteries = 4.2 Volts)

Yes but not as efficient as sodium hydroxide.

Very nice brother but you miss a point. The main idea is not separate the electrolyte from the electrodes, you have to renew the electrolyte time to time. Because after for a while the ability of the electrolyte to deplete aluminum will end up. At this point you have to replace the electrolyte with new one👍

'Catastrophic scenarios'...? Do explain ?

@@jshaw4757 isn't the word catastrophic self explanatory already? If your question is referring to how it may become catastrophic, then I suggest you use your imagination or just dig up some past events that weren't supposed to have happened but did due to some silly careless error, human error. So, its best not to go all out trying to create a battery someone showed randomly on the Internet all for the reason of wanting to save some few bucks while risking own or others' lives or limbs. Innovation must go on, but not all matured enough to know the difference between need and want.

@@aaronsingh6496 Well I've made countless batterys from many means and the info came from the Internet just like info came from a book one n the same belive it or not books are only wrote by humans and the same info or full book can be bought or read online...and no catastrophic isn't self explanatory it's a perceptional word what is catastrophic too me would be a volcano erupting n killing 1000s off people on the other hand a minor chance off a small shock maybe or a slight burn off some description if you don't pay attention too me is not catastrophic...you can chop a potato n harm yourself if your not careful may even loose a finger but I don't see anybody putting warning signs about chopping fruit...same too be said about purchasing a car I would suggest driving a car is vastly more dangerous too you and others than building a small battery with a volt or so and maybe half an amp or two will do you no harm yet a lack off concentration driving a car can wipe out ten people n ruin ten familys in a second so would you suggest such a catastrophic warning when buying a car ?

So the answer is he doesn't know what could go wrong. He's just a mom saying be careful

@@hoaacres7084 Fair play nothing wrong with warning people....putting people off from trying seems too happen alot though from certain warnings it's good too warn n advise but I would suggest try not too put people off from trying...and using words like catastrophic in a situation that cannot cause any harm I feel puts people off...cheers

Yes you can. It doesn’t matter.

@@joyofelectronics9782 ah, thank you! Also, I had another thought about your design. Couldn’t you get more energy out of it if you added more layers of foil/papers in the container?🤔

I's much cheaper the way he did it. Copper is expensive. Aluminum is cheap.

You can use either stainless steel or lead

@@joyofelectronics9782 should I make the lead into square and roll or?

U did not ans? Should the lead be coated too?

​@@joyofelectronics9782 I asked if the lead should be coated too

Lead or zinc

@@joyofelectronics9782 Thanks.

I showed in the video. It’s more than 1 amp.

@@joyofelectronics9782 Can the voltage be increased?

Right

Thanks brother. You can put regular potable water.

@@joyofelectronics9782 I mean the quantity like cm or litre

@@nnejiamaechi9385 l wish you said amount of water ☺️it doesn’t matter the solution should be not fully saturated

@@joyofelectronics9782 ok but is l One litre of water ok or too much for 500grams of sodium hydroxide?

The chemical reaction between aluminum and sodium hydroxide is determine the voltage. If you make it larger you get higher current.

The answers to your all questions are exist in video. But l will explain again: this battery is not a rechargeable battery, l mean you don’t need to charge it. When you put electrolyte it will work. When it has electrolyte it can provide electricity for 6 hours. After 6 hours you have to renew the electrolyte. So it can run the blender for six hours.

​@@joyofelectronics9782 He asked the ampere hour capacity of the battery .I am also eger to know it connecting additional cells in parrallel,is it possible to run higher loads?👈

@@harikumar4418 bro the the voltage is 1.25 volts the current is more than 1 amp so the battery can provide this current for six hours. It means the battery has 1x6 = 6Ah. Yes if you make more than one battery of this and connect them in parallel and serial you can handle higher load.

Are u saying at 1,3v with over 1amp it can carry blender and to the extent of 6.hrs

​@@joyofelectronics9782 you are good in ansg questions and will increase your followership

copper foil

When I say led lightbulb, I mean an led lightbulb like u use in ur everyday life, not these tiny lil indicator lights that just happens to be led. If that's what a person thinks of when they hear "led lightbulb" then they don't understand reality.

Çok teşekkür ederim kardeşim. Edison pilini biliyorum ama dediğiniz şekilde denemek aklıma gelmedi. Fırsat bulduğumda deneyip bilgi veririm kardeşim

@@joyofelectronics9782 aslında bu videodaki hazır sistemi dönüştürmeniz çok zor olmaz. En son Fe3o4 ile yaptığınız iletken boyayı biraz kalın bir şekilde alüminyum boru üzerine uygulayabilirseniz bu durumda alüminyum elektrod akım toplayıcı olarak çalışmaya başlayacaktır(bu videodaki bakır elektrodun akım toplayıcı gibi çalıştığı şekilde) . Fe3o4 sudaki OH iyonları ile reaksiyona girip paslanacaktır diye düşünüyorum. Fe3O4 + 8NaOH → Fe(OH)2 + 2Fe(OH)3 + 4Na2O gibi bir elektrolit reaksiyonu gerçekleşecektir. Buda şarj edilebilir bir bataryaya dönüşmesini sağlayacaktır. Eminimki son yaptığınız boya çok düşük bir dirence sahip olduğu için ciddi bir akım oluşacaktır bu dönüşümü sayesinde. Denemeniz için sanırım herşey elinizin altında :) Bilgi verirseniz çok memnun olurum. kolay gelsin kardeşim.

Ayrıca düşündükçe insanın aklına geliyor. Sodyum hidroksit elektrolitin derişimini bu dönüşümde düşürmelisiniz yada Fe3O4 iletken boyayı yeterince kalın uygulamalısınız çünkü demir oksit iletkenin tamamı pasa dönüştüğünde elektrolitte halen OH iyonları olursa bu iyonlar sanırım Alüminyuma da saldırmaya başlayacaktır. Ya OH iyonları tükenmeli yada Kaplama boya yeterince kalın olmalı.

Bu dönüşümün bir diğer avantajı demirin pası elektrolitte çözünmeyecektir. Fakat bu videodaki sistemde yani alüminyumun OH iyonları ile oluşturduğu Sodyum Alüminat elektrolit içerisinde gayet rahat şekilde çözünebilmektedir. Elektrolitin uzun ömürlü olmasıda sağlayabilir.

There is ventile hole on the battery. Probably you missed that part

There is ventile hole on the battery. Probably you missed that part

You have been told about the materials in detail during the video bro.

@@joyofelectronics9782 sorry but I can't hear properly So please its my Humble request

Sodium hydroxide

Absolutely

No

1 amp 1.3 volts. You can connect in serial or parallel to adjust voltage and current.

The voltage will be the same but the current will increase 5 times.

@@joyofelectronics9782 Thank you friend.

You don’t have to charge it. When you fill with electrolyte it starts to produce electricity when you empty it it doesn’t produce. That’s all, it’s so simple.

It’s not required to be charged.

It will be unreactive after sometime

No

Yes it is.

You are right and l touched on this in the video brother while sealing the battery box

It’s reusable

It doesn’t require to charge

@@joyofelectronics9782 I know, but can you to make the voltage higher

@@joyofelectronics9782 or is there any way to make it at least 5 V?

Yes it is. So that’s why we left a tiny hole on one of the battery pin. So you have to be careful about this produced hydrogen gas.

a hose from this device to a balloon to collect the hydrogen produced would allow you to create more energy

I read through out all the comments to see if someone mentioned this, surely, the reaction between Aluminum and Sodium hydroxide is very aggressive and used produce hydrogen to be used as fuel, it also creates a lot of pressure inside the cell and with a hole in it can let the electrolyte to spill out and causes damage to its surroundings. also, the Aluminum electrode will be dissolved very rapidly even if the battery is not in use. anyway, the instruction were good and maybe using another electrolyte can result in a safer battery. Regards!

kzfaq.info/get/bejne/h8-fkrSEnMDDdmQ.html&ab_channel=BasfiileDeneyselBilim bu videodaki gibi. Videodaki başlangıçta mavi sıvı diye anlattığı pet şişenin içerisinde elektrotlar ve elektrolit olsa üstteki petde ise sıvı yağ olsa. Pil kullanılmayacağı zaman ters çevirsek elektrotlar yukarıdaki pet şişenin içerisinde yağın içerisinde kalsa, elektrolit ise ağrılığından dolayı aşağıdaki pet şişede kalsa???

Merhaba kardeşim evet çok iyi anladım ama olay şu ki bu elektrolitin sürekli yenilenmesi gerekiyor, boşaltmaktaki maksat sadece pil çalışmasın diye değil. Çünkü alüminyum eridikçe elektrolitteki sodyum hidroksit tükeniyor ve yeni elektrolit eklemek lazım. Yoksa fikrin harika 👍

@@joyofelectronics9782 bu yolla hızlı şarj olabilen süperkapasitörleri boşalmaması için elektrolit içerisinden çıkartırsak ihtiyaç olduğunda kullanılabileceğini düşünmeye başladım

@@ozgurkaygisiz1562 olmaz o 😀elektrolit olmazsa çalışmaz onlar

@@joyofelectronics9782 hibrit kapasitör videosu izlemiştim çinko sülfat ile yapılan .kendi kendine boşalmaması için bu yöntemi düşünmüştüm

You can use regular white glue

I used sodium hydroxide. This is a typ of aluminum air battery so it’s normal the electrolyte deplet aluminum, the battery produce electricity via this way. But as the aluminum is very thick it will take very very long time to depleted completely.

Puedes traducir a Español, Spain, 🇪🇸 Gracias

@@maykaGM debes aprender a copiar y pegar un texto en internet y usar el traductor de google

How many amp hours will it produce. Have you done any experiments with it?? I could see several of these together for motorcycle battery

@@drewrinker2071 6Ah with same electrolyte

You can order on internet

İnternetten satın alabilirsin. Evde kendi yapman çok zahmetli ve kalitesiz olacaktır.

The output Of the wire must be one solid one

@@joyofelectronics9782 Thank you, I couldn't get past that part ❤

👍

Let it be love, what kind of word is that?

Hi. I told everything and parts in the video brother.