🤩👍❤️

🤩🤩🤩👍

Thank you. Do you have a channel?

Thank you 🤩

🤩✨️

Thanks my friend

🤩

good luck friend👌

Yes👌🤩

Yes.zvs

Should I change the no of windings if my core is a little bigger not much but a little??

I think it depends on how many volts you use

No, the circuit does not work correctly. It must be a 12V zener diode😄

@@electronicpuls3242 Brother, do you plan to make a 1000kv, 2000kv? I want to put this technology on the stun stick

@@user-in8bz3kd7d It's great. Be sure to make it my friend🤩

@@electronicpuls3242 Do you usually like these too? Speaking of making electric shock rods from 1000akV to 2000kv, I want to use electric shock rods again, and I want to use 1000kv to make super EMPs that can interfere with electronic factory products within 100 meters

@@user-in8bz3kd7d Yes, it is very enjoyable. It is very difficult to make such a voltage, is it possible? Can you make it?😁😂

Yes🤩😄

Make video plz

Yes

Yes👌

Yes, this circuit is for momentary use and cannot work all the time because it gets hot🤩🙏✨️

it's AC because any transformer can't work with dc output, also it's more like arc, then spark. If you want receive spark from this circuit, you'll need HV voltage multiplayer. Sorry for mistakes in my message right now i learn English not for long time

And also be careful when you make HV transformer. You'll need make winding away from border in around 2.5-3mm or 0.1inch, and use around 3 layers of isolation, if you use scotch, or 1 layer if you use insulating tape, don't worry if it can't work in first time it's completely normal, because HV transformer it's not so easy to make.

Yes, you can test.

@@electronicpuls3242 , thank you very much! I will test and use such a simple and power circuit. Your channel seems to be super interesting and useful, will wait for new videos.

So because the capacitor and inductor system is only to increase the output voltage zvs and have a sine wave through resonance and the transistors without the capacitor and inductor will alternately open and close as with the capacitor and inductor only giving less output power

It does not work for this circuit😄

🤩👍

Zener hère only for adjust a voltage of the Gate of MOSFET needed it

No

@@electronicpuls3242 deal thx

Yes✨️

@@electronicpuls3242 thank you😊

@@electronicpuls3242 thank you 😊

Did you make the same circuit?

@@electronicpuls3242 no, from another video I was just taking ur advice before making it.

MOSFETs burn very quickly, be sure to put a zener diode to protect them.... The circuit I made is very simple and strong, make sure to make it 🤩

@@electronicpuls3242 yes surely i'll try it

👍👌

No.

Bro first he tuned his transformer by increase size and turns of copper winding and second he doubled his Circuit like you just need 1 mosfet and resistor to make nice arc with transformer he doubled his Circuit

@@IshvOP i see now, he used a zvs circuit and properly insulated the transformer, hence the great winding to arc ratiio.

@@HashirEasa yes I but I didn't see the zvs Circuit. 😅

High current high voltage

Yes

Did you connect the number of primary rounds and zener diode correctly?

@@electronicpuls3242 Yes, I chose the zener 1N4742A 12v , but I wired more than 500 rounds to get more powerful

And I glued every 100 turn

Maybe the MOSFETs are burned...if the circuit is not connected correctly, the MOSFET will burn soon. Test the MOSFET😄

Yes, I think the transformer is a maximum of 15 kv.

why don't you make the original ZVS with an inductor, a capacitor and a flyback transformer? the discharges would be much larger

I wanted the circuit to be simple and strong.

I will make it with flyback later

Will you be doing dual coil or single coil?