How To Make Twin Motor RC Model Airplane - DIY Brushless Motor Model Airplane.

Рет қаралды 6,461,130

4 жыл бұрын

How to make 2 brushless motorized remote controlled aircraft from foam board material.
INFORMATION: The Foamboard is made of foam and the outside is paper-covered. It is lightweight, robust and easy to cut. Easily bonded with hot silicone.
All of my videos : bit.ly/2Z9QVYK
Thank you for watching. Please Remember to Share and Subscribe for More Amazing Videos.
SkyRC Dijital LiPo Charger: ban.ggood.vip/T1oJ
Discount coupon: BGT6X80
Thanks for watching. If you want to support my channel, join.
/ @kendin-yap
Diagrams for dimensions: bit.ly/2NEy4S9
INFO: Two brushless motors may not work with one ESC. In this case, it is necessary to use two ESCs. Some brushless motors can run smoothly. The T-motor brand Air series motors that I use in this airplane work smoothly with a single ESC.
Necessary Materials:
2 pieces of brushless motor 2205 1800-2600KV. (2204 can also be):
www.banggood.com/custlink/GKK...
2 pieces (CW & CCW)
Two Blade 6x4 or three blade 6x3, 5x4.5 propellers: www.banggood.com/custlink/vvm...
OR
www.banggood.com/custlink/KmG...
30A Brushless ESC (35-40A can be used according to the motors you will use):
www.banggood.com/custlink/vDK...
OR
www.banggood.com/custlink/3DK...
OR
www.banggood.com/custlink/DDv...
if you want to use two ESC: 2x 20A ESC: 2 x www.banggood.com/custlink/Kv3...
11.1V 1300Mah LiPo battery:
www.banggood.com/custlink/DKG...
3pcs 35-40mm Wheel:
www.banggood.com/custlink/DvK...
Servo control horn:
www.banggood.com/custlink/KKK...
4 or 6 channel radio control system:
www.banggood.com/custlink/mKG...
4 micro servos (may be 9gr servos):
www.banggood.com/custlink/vvm...
Gold Connectors 3.5mm (for Y cable):
www.banggood.com/custlink/vDK...
Wheel stopper: www.banggood.com/custlink/KGv...
Y extension cable: www.banggood.com/custlink/D3D...
L type nylon clevis keper clip: www.banggood.com/custlink/33m...
Adjustable Linkage stopper (Easy Link): www.banggood.com/custlink/KD3...
Lipo Battery Charger: www.banggood.com/custlink/vKm... OR www.banggood.com/custlink/Kv3... OR www.banggood.com/custlink/GDD...
Hot melt Glue Gun: www.banggood.com/custlink/Kmv...
Pushrods: tinyurl.com/feccnxaf
2mm Rod For Landing Gear: tinyurl.com/rtxk9b9x
Some of the shops that sell Kraft Foam Board:
www.amazon.in/Pacon-Water-Res...
pacon.com/board-480/water-res...
tinyurl.com/4ups272k
www.foamboard.shop/en/foamboa...
www.enasco.com/p/Pacon-Water-...
www.mwmaterialsworld.com/es/p...
SJ5000X Camera: www.banggood.com/custlink/Gvv...
Technicial Specifications:
Lenght: 60 cm
Wing span: 87 cm
Flight weight: About 715 g
Center of gravity: 4-4.5 cm from the front of the wing
Required control system: 4 channels, 4 micro servos
Suitable battery: 11.1V 1300Mah - 1600Mah Lipo battery
Suitable motor: 2205 - 2204 (1800-2400KV)
Suitable propeller: 5x4.5 - 6x4

Пікірлер: 2 600

@654Geoff 4 жыл бұрын

This is what I love to see, someone making then flying a project from basics . Just as I remember it was when building involved thinking from first principles, most important well done love it. Such a tonic to watch. 👍

@babumohan4549 4 жыл бұрын

what a lovely rc plane making with neat explaination? simply superb flight but the hard work behind that plane is mind blowing.cheers from india.

@humbleperson766 4 жыл бұрын

Wow that's a very impressive project, from the design and construction of the plane, to placing a video camera on the nose of the plane -- so we can get aerial views of the surroundings below. It's a job well done. Thanks.

@madhukayanadath4942 3 жыл бұрын

Bautifull plane

@EgorKlepikov-ju7jt 2 ай бұрын

I'm a newbie in this hobby and started exactly from this plane. Nice tutorial. Thank you! Hope to see "Mig 17" with 3d printed turbo engine build from scratch

@thee_draagon 4 жыл бұрын

I watched the whole video and I felt so happy when the aircraft was flying...

@ashnaanjanajoy7518 4 жыл бұрын

@diyanathdissanayake7466 4 жыл бұрын

this is amazing... good product and creative. . And also when i search the video i found a video like yours. it also look yours one. here is the link. kzfaq.info/get/bejne/eKyTpbeYrZeWmHk.html

@johncoxwell9224 4 жыл бұрын

Diyanath Dissanayake save

@johncoxwell9224 4 жыл бұрын

Save to photos

@langatpeter4214 4 жыл бұрын

Me too! Great job!

@cowprez 4 жыл бұрын

Good job. A lot of work went into the making of this aircraft. Nice to see you get it to fly. When I built mine, on the maiden flight, I flew it into a tree!! I still have a good laugh after all these years!!!

@user-dn1cr6nb1c 4 жыл бұрын

Thanks for sharing. It is so exciting to see the airplane take off at the end and land safely.

@amilcararevalo2379 4 жыл бұрын

Excelente trabajo amigo mi hijo y yo admiramo por completo el video....! Felicitaciones, Saludos.!!

@user-yv9ft5xr9y 4 жыл бұрын

飛んだ瞬間感動した。マジスゲ！

@priyanshpal6665 4 жыл бұрын

The video was so gentle and I just loved it. All the steps are shown which makes it easier for us to make. I will also try to make the same. LOVED IT...!

@binzulost5369 4 жыл бұрын

Did you make it?

@vaibhavjain2791 2 жыл бұрын

Very good and detailed demonstration and making of sturdy and feature full plane . Very good flight test, the flight and its recording is wonderful and in a nice location. Superb, brilliant!

@sunchaserw1477 4 жыл бұрын

It gave me so much fun to watch building this plane from a piece of foam till it was all finished. The only thing I did not understand and love to learn was the connection of circuit

@honkhonk8009 4 жыл бұрын

Its really simple. The battery is connected to an ESC, which controls the speed of the motor, and provides a stepped down current for the receiver to work with and the receiver sends a PMW signal to the servo to tell the servos what position they should be in and sends the same type of signal to the ESC to tell the ESC what speed it should drive the motors at. Its really simplified but i hope it helps.

@M5guitar1 4 жыл бұрын

Nicely done and well documented. I love scratch building too for over 50 years. Excellent work.

@johnk.7729 4 жыл бұрын

すごい！ワンダフル。脱帽。少年魂を忘れない人。感動。(^^♪

@ghanshyammainak564 4 жыл бұрын

Are you mad

@AsdfAsdf-jh6qi 4 жыл бұрын

03054391750

@user-qm7xl7dy3m 4 жыл бұрын

I finally made a plane and 6ch controller in accordance with your guide. Thx for your video.

@hoskbreaker 4 жыл бұрын

amazing, great proyect and the process is very enjoyable. Maybe someday use this video to build one

@mohammadshabaz7597 7 күн бұрын

I want to work with brushless motors but do not know where to insert which wire

@Santanu_Pal 4 жыл бұрын

Thank you very much for this engineering project. Its fun and lovely.

@jose1951muniz 4 жыл бұрын

Congratulations! became a powerful model plane with excellent controls.

@skyz3ra 4 жыл бұрын

Oh and you actually put everything needed to do it ourselves in the description i love you

@selehadinhabesi3855 3 жыл бұрын

i love you too

@charleshobson4093 3 жыл бұрын

Hey, thanks for the design. I built one. Very easy to build (If you have built a foam plane before.) I have everything on have to build it except the motors. They are on order. Can't wait to fly it.

@vuthap99 4 жыл бұрын

Congratulations for your working that make Motor Model Airplane flying well , good sir !

@shravan1981 4 жыл бұрын

Very detailed... I like the attention to detail about adding reinforcements. I am a bit worried that I will not do the placement of servo on the wings... Can you provide more measurements for that. All-in-all amazing build.Loved it.

@bekirharmanc1821 4 жыл бұрын

Ne kadar keyifliydi anlatamam =) Birçok teknik öğrendim, en kısa zamanda deneyeceğim. Teşekkürler

@gopalkishanpanda6623 4 жыл бұрын

Mera channel ka video thoda dekhlo

@Raazvloger6391 4 жыл бұрын

@@gopalkishanpanda6623 Bhai wo Indian nhi ha

@henrykasirye4731 4 жыл бұрын

One day

@ismailalkan6256 4 жыл бұрын

Git hazirini al daha ucuza gelir

@prasen9348 4 жыл бұрын

We made this project for our college program and finally we got success✈️

@FazedSoul 4 жыл бұрын

Glad to hear. I was thinking of doing something similar.

@madhiyand516 3 жыл бұрын

Which type of problem you faced during making this project please tell me bro I'm also trying this project

@prasen9348 3 жыл бұрын

@@madhiyand516 1.weight of the plane because lack of availability of foam board

@MCsCreations 4 жыл бұрын

Beautiful work, dude! Really nice! 😃 You should try putting FPV in one!!!

@monkeyman7048 4 жыл бұрын

MC's Creations. How are you not verified? 8.4k subs?

@mohammed_the_train_spotter 4 жыл бұрын

German Hunter KZfaq sucks

@monkeyman7048 4 жыл бұрын

depressed as always. Yeah no kidding

@MCsCreations 4 жыл бұрын

@@monkeyman7048 No idea, dude. Go figure. 🤷‍♂️

@mohammadshabaz7597 7 күн бұрын

What is FPV?

@afakkhan9283 4 жыл бұрын

The best DIY of my life...amazing...thanks man...

@melvinprudente976 4 жыл бұрын

I'm happy that it fly, great work!

@arhinfordjourankamah7364 4 жыл бұрын

I love this project. Great work boss. I'LL try to replicate it to make one for my younger bro I'm sure he'll appreciate it. Great work.

@sonerince645 4 жыл бұрын

Hocam eline emeğine sağlık. Uçağa kamera koymak ve görüntü almak çok güzel olmuş. Böyle görüntüleri bundan sonra ki videolarda da bekliyoruz 😊

@ganeshrvgk 4 жыл бұрын

I really like it, when I had ample amount of time, I didn't have money to make like this and when I had money I dont have time.

@AngryHybridApe 4 жыл бұрын

If you can get a radio and reciever, a motor, a few propellers (cuz you're gonna bust a few), an ESC, and a Lipo battery, the hard parts done. He puts alot of work into something that wont last for most people. If your new to it, you're gonna crash ALOT. Dont put alot of money into the plane. Dollar Tree sells 20"×30" foamboard for $1. I found its cheaper, easier, and more fun making tube planes. Basically, you make 2 different sized tubes (3"× 2 1/2" and 2 13/16"× 2 5/16" ((the smaller one is 3/16ths smaller on all 4 sides so it fits snug in the bigger tube. Big tube is "30 long, smaller is 20" but is cut in half. One half holds the motor, esc, battery and reciever. Preferably in that order. The end with the receiver slides into the bigger tubes about 5" in. The vertical and horizontal stabilizers are glued onto the other half, allowing 5" to slide into the big tube. Elevator and rudder servos are mounted through the top of big tube about 5" from the rear if big tube, where wiring can extend out of the front of big tube 2 or 3 inches. Long enough to plug them into the reciever while the front small tube is pulled out. Foot long control wires connect to popsicle stick ends at 45° angles with holes drilled in used as control arms. Coffee stirrers used as guides glued to big tube. The wings are easy. Two boards. Each one 20" long, 8" wide. Just like he shows how to make 90° angles by shaving 45° off of both sides you have to shave about 60° both sides. This part is easy but important. The top gets curved, the bottom doesnt. So, the top is 9" wide and the bottom is 8". When you get the angles shaved, get a broom handle or long round bar and smash the inside of the top piece near where the they were shaved. This gives the wing the venturi bump. Top of the bump should end up about 1/3 from the front edge. Glue the two ends which should match up. When you've done both halves, glue them together. You should now have a wing 40"× 8". If you know anything about dyhedral angles, nows the time to do that. If not, dont worry about it. I dont do landing gear. Throw and land in grass. The beatiful thing about this whole thing is that it assembles and disassembles, except for the wing you can disassemble it, but it has to be reglued each time. When I get it down where I can make a video thats easy for me to explain, I will. That should be soon.

@vedpatel8365 4 жыл бұрын

Kittelizer Laurelott have you build this design

@vedpatel8365 4 жыл бұрын

Kittelizer Laurelott can you tell me if you use 2 motors for one ESC will it effect your motors power or speed or will it stay the same

@AngryHybridApe 4 жыл бұрын

@@vedpatel8365 No. I think you gotta use one for one. If you put two motors on one ESC, they'll both run slow and/or fry the ESC. I think.

@vedpatel8365 4 жыл бұрын

Kittelizer Laurelott your right I think this video is fake. Fake like he really did build the plane but he is not providing real links or links to the electronics that he used. He is showing use links from the same company maybe he has a brand deal with them. He also uses different ESC battery and motor and they aren’t the same as the one he provides in the link below. When I ask him for the real link he didn’t really so I moved on from this video and saved my money. I would do the same if I was you.

@oldblacksmith2537 4 жыл бұрын

I love your work and I watch your video very fondly you make very good video and I like your channel very much hope you are well

@oldblacksmith2537 4 жыл бұрын

Thank you very much for reminding us that we will be grateful to you

@smartassist9700 4 жыл бұрын

Ohh I see your wonderful item list. THANK YOU FOR LISTING IT. Wow I need to save for a year or more. I have to be patient.

@user-ne5wk1xp1h 4 жыл бұрын

Все четко и понятно! Шикарный самолет для первого раза!

@aldeen19 4 жыл бұрын

Would you please tell me where is the location of this RC runway? One of the best helpful features of your DIY channel is the English text instructions. Thanks a lot man for your effort and yet for your kind will of sharing your lovely hobby videos. Keep on enjoying us with your amazing projects.

@Kendin-Yap 4 жыл бұрын

This RC Runway is located in the Kurtköy district of İstanbul

@miatasarm6452 4 жыл бұрын

@@Kendin-Yap yapıp satarmisiniz fiyatı ne olur ? Biz sizin kadar kabiliyeti değiliz basarilar

@adebayoagbaje 4 жыл бұрын

The illustration is detailed and precise. Imagine the level of precision that will be required to design a real aircraft. Awesome!

@javajav3004 4 жыл бұрын

its a real pain

@user-do9wm7pr5v 10 ай бұрын

Sir what material need to make this airplan

@Colliecol1 4 жыл бұрын

Worthy of applause. I salute you. It was like watching a skylark my favourite bird.

@Kendin-Yap 4 жыл бұрын

Thank you

@theoztreecrasher2647 4 жыл бұрын

Congratulations young fellah. This is the best build-it video that I have ever seen!

@frontier285 4 жыл бұрын

One of the best flying creatures I've ever seen, and a professional video maker made also.

@pixelgun1025 2 жыл бұрын

Chất lượng, Sỹ Luân chắc thích bản Cover này lắm này! Chúc mừng em cùng toàn thể Ekip F. Studio

@MG-wx8yx 4 жыл бұрын

Dude, that's awesome. From 27:37 I felt like I was flying this thing, OMG.

@honkhonk8009 4 жыл бұрын

Search up FPV. Its basically a hobby where people strap on really low latency cameras on their aircraft and fly it around

@kamilbubalik1993 4 жыл бұрын

Great video! You inspired me to build my airplane model :D

@andreslozano3631 4 жыл бұрын

what incredible work. Congratulations.

@kaustubhpathak9001 4 жыл бұрын

So nice work you have done dude....

@data-bass 4 жыл бұрын

this was awesome to watch, so inspiring. i suppose learning to fly one of these planes is the first step before building one!!

@manasedwankar1330 4 жыл бұрын

I watched the whole video and I felt so happy when the aircraft was flying.

@orxeletronicosltda4210 4 жыл бұрын

Vou Oi, tudo bem eyu8yfm O governo do lii880pi

@manasedwankar1330 4 жыл бұрын

I don't understand your language

@keremayan452 4 жыл бұрын

@@manasedwankar1330 Nobody does... :)

@ammarawad5643 3 жыл бұрын

Good

@maurogarcia8882 4 жыл бұрын

AMAZING! MASTERCLASS! THANK YOU VERY MUCH! MASTERCLASS!

@pronubby2132 4 жыл бұрын

I never knew something that small could travel that fast by propelling air!

@reedanthony106 4 жыл бұрын

And he put a camera in it too! Good job! 💯💯💯

@ogchidel2106 4 жыл бұрын

Nice work! Here, we can't get those type of foamboard easily. I have a wing made for a flite test cub. I also have 2306 motors laying around. I think I'll make your fuselage and mate it with the wing. I've always wanted to build a twin motor plane

@henrykasirye4731 4 жыл бұрын

Me 2

@abhisheks3127 8 ай бұрын

what material did you use for the wings?

@ogchidel2106 8 ай бұрын

Polystyrene foam board

@wewannado 4 жыл бұрын

It was so nice to see it flying after all that work :)

@ahmedazher5264 4 жыл бұрын

ikrrrrrr

@messilionel1267 4 жыл бұрын

ضجثكوثثيكومقاافتطدثجثد

@oguztapan8210 4 жыл бұрын

Emeğinize sağlık muhteşem bir çalışma ⚒ 👏🏻👏🏻👍🏻

@saik9584 3 жыл бұрын

25:21 to 25:31 low budget rc plane shaped rc car edit: great video man ..looks dope

@user-zo8ez7cs1p 4 жыл бұрын

すばらしい

@romeomorin1490 4 жыл бұрын

Good work, model flew just like a full scale.

@santomac_givergiver833 3 жыл бұрын

Luar biasa.. mantap.. sungguh saya salut dengan karya anda... saya sedang belajar RC airplane.. maaf saya tidak bisa bahasa inggris.. Terimakasih..

@judithperez5838 4 жыл бұрын

bro this is godly! love the way how it flies

@SHIVAMYADAV-jc5sg 4 жыл бұрын

thank u bro for making this video im a beginner thanks a lot

@denniskinuthia7584 4 жыл бұрын

Very impressive! Nice video. A big thumbs up from Moi University in Kenya.

@retrogamer1683 4 жыл бұрын

Thank you so much brother you really made my day and I felt happy that people like you exist thanks bro I hope you have much more good ideas

@Kendin-Yap 4 жыл бұрын

Thank you.

@retrogamer1683 4 жыл бұрын

@@Kendin-Yap No problem

@beckerf4n 4 жыл бұрын

what a genius!! love it.

@JustinDancingHawk 4 жыл бұрын

This is SOOooooooo COOL! I sent the link to my Grandson!

@sidneidesaalves7960 4 жыл бұрын

adorei,cara ficou show parabéns

@jeremie2020 4 жыл бұрын

I wish I was as skillful as you. Awesome work, looks so easy for you, that's depressing...lol

@jimmy2times 3 жыл бұрын

The twin engine flyes much better! Amaizing work!

@JPapavas 4 жыл бұрын

I wish i had the skill's and the experience, great job.

@worldmapping4895 4 жыл бұрын

its quite easy

@harinandr450 4 жыл бұрын

The landing was so smooth

@saiyadaajafri1901 3 жыл бұрын

✈️✈️✈️🛩️🛩️🛩️🛫🛫🛫🛬🛬

@doserastalmi 3 жыл бұрын

@@saiyadaajafri1901 thanks for the sign language I was not able to understand it in English......

@frednel4326 4 жыл бұрын

Verry informative video and a verry cool flyer for chesp too..10 stars bro 👍😉

@skylerbass4417 4 жыл бұрын

thanks for making this vid it helps me to be able to play with something while I'm in quarantine

@polzchannel9784 4 жыл бұрын

Tjakepzzz 👌👍 Sangatzzz Creative ✈💯👏 Very 👌👍 Nice

@alonsobrosmann4300 4 жыл бұрын

Önce her zamanki gibi yabancı bir kanal izlediğimi düşündüm sonra bir baktım ekranda Türkçe yazılar yazıyor.Nasıl sevindim anlatamam.Sonunda uçakta uçtu ya 10/10.😎😎😎

@ericw.6107 4 жыл бұрын

That's it; I'm making one! Excellent video brother!

@Mahirnanda56 3 жыл бұрын

I am too

@sidamarali3030 4 жыл бұрын

Those left-handers are always skilled

@pierregringoire687 4 жыл бұрын

helal olsun wallaha mükemmel yapmışsın ellerine sağlık

@juanjoairbalet 4 жыл бұрын

Impresionante!...buen trabajo

@malteflechtner579 4 жыл бұрын

So Nice , a good Idea for a Beginner like me I will built it

@emresengun4657 4 жыл бұрын

Harika çalışma. Tebrikler ve teşekkürler.

@redeyes24man48 4 жыл бұрын

I love your hard work keep it up

@EdgarCasteloInventor 4 жыл бұрын

Magnífico!

@FuadPhenomenon 4 жыл бұрын

is it possible to make smaller rc plane using one of these motors? What will be the required battery? Thank you.

@beckerf4n 4 жыл бұрын

i see it on youtube smallers and everyone needs batteries.

@togetherforonegoal9210 4 жыл бұрын

That was amazing. respect

@user-vg5mc4zo2z 4 жыл бұрын

Красавчик все понятно и легко.

@NGlitchesFTW 4 жыл бұрын

Thats sick!!

@saiyadaajafri1901 3 жыл бұрын

🛩️🛩️🛩️🛩️✈️✈️✈️✈️🛫🛫

@banuanton7668 3 жыл бұрын

Ima try it

@Lakmalyoutube 2 жыл бұрын

What are the thinks needed to make this.

@redfordrn 4 жыл бұрын

Excellent job Turkish Brother. Love from Pakistan.

@bamsgian9759 3 жыл бұрын

I thought he from russia

@Jeferson8319 3 жыл бұрын

This project was great.

@HasanAraycProjects 4 жыл бұрын

Tebrikler üstadım👍👍👍

@dimidabi7423 4 жыл бұрын

So beautiful. You are a great master. Thank you for this video.

@aeromodelisme45 3 жыл бұрын

Encore une super vidéo, d'un modèle original sympa de donner tout les liens pour trouver les différents matériels, Bravo pour vos vidéos ! bons vols...

@chomxomtv6844 4 жыл бұрын

great! I wish I could do that

@TRSQUADTV 4 жыл бұрын

Baştan sağma olmayan güzel bir iş.. ellerine sağlık...

@pertevonur471 4 жыл бұрын

amazing !!!! keyifle izledim.....

@user-cq9wk7gi8k 4 жыл бұрын

Здоровский самолётик получился ! У вас руки растут из правильного места !

@cristianondo6118 4 жыл бұрын

Cuando lo he visto por primera vez me quedé sin palabras ,.very good

@Akash-12507 4 жыл бұрын

I can see you worked too hard for it . I wish that I can also make it like you.

@oyeniyioluwaseun2598 4 жыл бұрын

fun with Ashish nice job I will make a drone

@Akash-12507 4 жыл бұрын

@@oyeniyioluwaseun2598 ya I can also make it. If you have that much of skills then you can make 😋😛😝

@yamatosawa2748 4 жыл бұрын

素晴らしい！　ライト兄弟がこれを見たら大口開けたままフリーズするだろうな(^o^)

@terratrekker2 4 жыл бұрын

Sad that someone would dislike this video.

@furkandemir3856 4 жыл бұрын

İ think so :(

@callofdutymodernwarfare943 4 жыл бұрын

Hey man you are the first one who show how to make an esay peasy airplane with the mesure The best❤❤❤

@enginakca1547 4 жыл бұрын

vay arkadas ben kumandanın pilini değiştiremiyorum, millet neler yapıyo. helal olsun...

@carlosmurphy4u1 4 жыл бұрын

Great job, just a side note, generally rubber bands are installed from front to back, gives more downward tension on the leading edge preventing lift but on a light plane like this its no matter.