Brilliant and Extrodinary Work......Masterful Indeed!!
@user-ge6mz2tf7y3 сағат бұрын
abi çok güzel olmuş eline sağlik bi sorum olucak drone için hangisi daha uygundur acaba?
@user-su6wg5yh9u3 сағат бұрын
can someone also tell me how much the whole price of buying everything rounded up
@user-su6wg5yh9u3 сағат бұрын
I think its like 120 franks / 134 $
@user-su6wg5yh9u4 сағат бұрын
your an amazing pilot and a creator I am 13 and am going to buy all the materials and make this plane myself wish me luck and I love ur channel keep makin videos
@holderking96716 сағат бұрын
What does the epoxy do is it like glue
@user-by6yz1nd5g11 сағат бұрын
опа байрактар
@BeznawaAschalew16 сағат бұрын
Hello Kendinyap I have made this plane and Remote using your Code It looks nice. 👉but why does The motor works(Rotates) when i switched off the Remote. How should i correct the Code of throttle not to rotate unless i press the joystick
@Kendin-Yap11 сағат бұрын
You can try a few times by changing the "0" value in the following line in the receiver code. You can try the value 127 first and then the value 255. This affects the channel position when the transmitter's signal is interrupted. data.throttle = 0; // Define the initial value of each data input. But the basic security rule is this; The transmitter should not be turned off while the receiver is active. The receiver must be powered off first. Then the transmitter is turned off.
@BeznawaAschalew11 сағат бұрын
Thank you So Much Kendiyap🙏 I have Updated my Knowledge through this Progress. I have almost finished The Project. I will Show you when i finished🙏 God Bless You for Your support.
@dmitrytrunikov730517 сағат бұрын
@Kendin-Yap, nice work! What type of a clue did you use?
@Kendin-Yap11 сағат бұрын
Hot silicone
@bezasck8490Күн бұрын
Hello Kendinyap I have made this plane and Remote using your Code... With 1000KV brushless Motor. It looks nice. 👉but why does The motor works(Rotates) when i switched off the Remote. How should i correct the Code of throttle not to rotate unless i press the joystick
@Kendin-Yap11 сағат бұрын
You can try a few times by changing the "0" value in the following line in the receiver code. You can try the value 127 first and then the value 255. This affects the channel position when the transmitter's signal is interrupted. data.throttle = 0; // Define the initial value of each data input. But the basic security rule is this; The transmitter should not be turned off while the receiver is active. The receiver must be powered off first. Then the transmitter is turned off.
@tammyff749Күн бұрын
Pls if I use ardiuno nano atemega 168 for the transmitter and use nano atemega 328 CH340G for the receiver would it work
@muhammeduzelКүн бұрын
Merhaba tüm tek motorlu uçaklarda acı veriyordunuz bunda neden açı vermediniz acaba
@Kendin-Yap11 сағат бұрын
Bu arkadan itişli ve motor çok geride olduğu için gerekli değil.
@furquan2792Күн бұрын
can i use 2210 1000kv motors with 1045 props instead of 2000kv?
@Kendin-Yap11 сағат бұрын
1045 propeller is very long. It hits the fuselage.
@furquan279210 сағат бұрын
@@Kendin-Yap so can i just put it away like 6 iches from fuselage? will that work or can u suggest a differnt design??
@Er_Maneendra_SinghКүн бұрын
Thanks a lot Sir ji, I’ve also made a Transmitter by using your circuit and code. And It’s working 🙏🏻
@Abooscarbenny2 күн бұрын
bank angle but survived!
@mostafizbillah71242 күн бұрын
Can i use 3s lipo battery
@Kendin-Yap11 сағат бұрын
No you can't.
@jorgennorberg71132 күн бұрын
Fantastic attention to detail.
@skTGFB25772 күн бұрын
What is the voltage of the 100uf capacitor
@Kendin-Yap11 сағат бұрын
16V +
@uzelektroniktv85672 күн бұрын
Please make next video
@uzelektroniktv85672 күн бұрын
Perfect
@Daivik_-fy3nd3 күн бұрын
could you please give more info about the RC and the electronics thankyou
@Kendin-Yap11 сағат бұрын
There is a link to the RC video below the video.
@gabrielrezende33943 күн бұрын
Where can I find the plugs to soldering? Tnks =)
@Kendin-Yap11 сағат бұрын
There are links to the materials below my videos on RC airplane construction.
@shunlifegamerz67633 күн бұрын
What is the exact weight of this plane ??
@Kendin-Yap11 сағат бұрын
182 gr
@dradden15563 күн бұрын
Looks redicuous
@shunlifegamerz67633 күн бұрын
What is the exact weight of the plane ??
@Kendin-Yap11 сағат бұрын
495gr
@georgemattam-yb7ch3 күн бұрын
can you plesae show how to make the kk2 1.5 flight controller in your next video pls
@Kendin-Yap11 сағат бұрын
The video on how to make a remote control is already available on my channel. The links are below the video. Click "more" or "show more"
@playstation073 күн бұрын
Can we use Bread board
@Kendin-Yap11 сағат бұрын
Yes you can. But too much cable clutter will cause electrical noise. In this case, connection problems may occur for the receiver and transmitter.
@playstation078 сағат бұрын
@@Kendin-Yap can you explain?
@hisarbeyli664 күн бұрын
merhaba anlatımlar için teşekkürler, sayenizde ilk uçağım havalandı, bu modelde benmi yanlış saydım acaba, video başında 4 adet servo gerekli diyorsunuz ama 5 adet monte ediyorsunuz, 1 tekerlek, 2 kanat, 2 adet arka dümenler için
@Kendin-Yap11 сағат бұрын
Direksiyon servosu opsiyonel. Şart değil. Sonradan eklediğim için videonun başında göstermemişimdir. Bu model kısa mesafeden kalkabilir. Bu yüzden teker yön servosu olmasa da olur.
@bakibahar36304 күн бұрын
Ustam kanat içi desteklerin kanattaki yerini nasıl yerleştirdiniz
@BPM19864 күн бұрын
Hey kendin yap im your subscriber and you are my moat favorite youtuber but i want you to make the most fastest rc plane with defensive system like ammo but not real one pls do it thanks
@knowledgebyte4 күн бұрын
Hmmm, nice, but at €56 that’s too expensive considering what else is out there in the market. A very nice production though and quality build. If you scaled that up a bit, it might sell for that price.
@puriap2504 күн бұрын
This super cool and well made.
@bhodabesra17674 күн бұрын
Remote ka daygram and receiver ka daygram
@Kendin-Yap4 күн бұрын
All links are below the video. Click "more" or "show more"
@nipunprakash55974 күн бұрын
Can we use IRLZ44n mosfet instead of the IRFZ44n mosfet? Because in my locality this one is not available
@Kendin-Yap4 күн бұрын
Yes you can
@mostafizbillah71244 күн бұрын
What if i use bldc motor instead
@oscarshilongo-ps9ut4 күн бұрын
wow amazing work i wish you were my bro so the boat can be miyn
@adunsky5 күн бұрын
Great project! Do you have any projects involving an IMU ?
@mauricechaouat94575 күн бұрын
thank you so much for yours videos,
@emirhankorkmaz51775 күн бұрын
Admin bey bayadir aboneyim size meslek okulunda okyorum 11 sinif öğrencisiyim bilgisyar okyorum gelir geldi 20 bin Turk lirasi dronu yaptık ama 3 pervane dönüyor 1 tanesi dönmüyor neyden olabilir arızası yardimci olurmusunuz sonradan yaptınız vidyoda göstermediniz bir ince ayar olabilirmi lutfen yardimci olurmusunuz
@Kendin-Yap4 күн бұрын
3 motor çalışıyor biri çalışmıyorsa muhtemelen ya bağlantı ile ilgi bir hata vardır yada esc de bir sorun olabilir. Motorlar için ayrı bir ayar mevcut değil. Çalışmayan motoru ve ESC yi diğer çıkışlara bağlayıp çapraz testler yaparak sorunun motordan mı, ESC den mi yoksa bağlantılardan mı olduğunu bulabilirsiniz
@WaliKhan-br3wy5 күн бұрын
Please how to find this things please help me and you send me
@jaymasson88736 күн бұрын
Good day. If you don’t mind me asking, where could I find that beat you played at the ending of the video?
@Kendin-Yap5 күн бұрын
Music is from KZfaq music library. You can find it in the detail section of the video below.
@user-kn6vv1bb2k6 күн бұрын
ลูกอีช่างซื้อดูซะ..หัดทำเองมั่งนะ
@atvali3096 күн бұрын
Nice project ! Can we use 2 motor to x2 speed ?
@Kendin-Yap5 күн бұрын
There may be some speed increase, but not 2 times. For high speed, a slightly larger motor with a higher KV value can be used. But this model is not suitable for 2 times the speed anyway.
@bugra.ozkn06 күн бұрын
Bu video ile bağımsız ama 11.1v lipo pil voltajını arduino nano için 10v altına indirmek için L7805cv regulatorü kullanabilir miyiz? Nano 5v ile 10v arasında herhangi bir voltajda sorunsuz çalışabilir mi?
@Kendin-Yap5 күн бұрын
7 ile 9V arasında bir giriş arduino nano için uygundur. 7808 veya 7809 kullanabilirsiniz. REgülatör devresinde 2V kaybolacağı için 7809 ideal bir seçenek olur.
@KJIaBogaB6 күн бұрын
Amazing!!!!!!!!!!!!
@attilabled6 күн бұрын
Kanal çok kaliteli
@nightwarrior55167 күн бұрын
How from where can I buy these things ?? Please I want to build my own rc plane
@Kendin-Yap6 күн бұрын
Links to the required products are below the video. (click more)
@user-rb5lk1pu5p7 күн бұрын
Bro how can I see the serial monitor in mobile?
@mehmetmala63107 күн бұрын
Kral❤
@phnphn30037 күн бұрын
merhaba linkte verilen parçaları motorları birebir aldım tam ölçü yaptım fakat verdiğiniz motorlar çok güçsüz uçağı kaldırmıyor son gaz havaya atıyorum 10m gitmeden yere çakılıyor dikkat ettim linkte verilen motorlar la sizin kullndığınız motorlar farklı gibi
@Kendin-Yap6 күн бұрын
2300kv 1806 motorların hepsi uygundur. Modelin ağırlığı önemli. Pil 1300mah ten büyük olmamalı ve modelin toplam uçuş ağırlığı belirttiğimden fazla olmamalıdır. İnşa sırasında buna dikkat etmelisiniz. Pilinizin sağlıklı olduğundan da emin olmalısınız.
@SuperONOO7 күн бұрын
Najprv si si mal osadiť tie velke sučiastky potom tie male by sa ti tam ľahko dávali