How to Make your own Floor panels for Lund SSV14

Рет қаралды 12,596

4 жыл бұрын

In this video I show some of the steps I did to make my own LUND SSV14 floor panels. I did not show step by step, but basically how I designed my own floor panels. I removed old carpet and installed Linoleum to help with cleaning ability, comfort, and be a little more water resistant. Be sure to check out a few other boat videos and maintenance vids on my channel. Drop a Like, or share this video. SUBSCRIBE today! its much appreciated. Thanks for watching!

Пікірлер: 23

@vernshein5430 3 жыл бұрын

I have a 2020 14' SSV and I just took some 3'x3' skeletal interlocking heavy rubber mats from my gym and garage. I cut them so they fit between the seats. They cushion the floor, reduce noise and are very grippy yet waterproof.

@bigair0176 3 жыл бұрын

Sweet! I wanted some flat floors to be able to stand up and be somewhat stable. The v in the front floor is quite deep so much better being flat. Cheers!

@orviskid Ай бұрын

I have a 2000 ssv 14, the ressr piece rotted alittle. Why did you screw thruthe vinyl, and not screw the base on first. I don’t want the screws showing

@bigair0176 Ай бұрын

Did y use glue on the vinyl. Hind site might have been better. Used the screws to help hold vinyl on. No other reason really

@deathofcobra Жыл бұрын

Hi i am interested in doing the same to my boat so you have a measurement please and thank you in advance

@baggersvancelegendof835 3 жыл бұрын

Does the back board sit flush with the middle walkway? I'm measuring my ssv14 and 52" wide seems like it will sit a bit raised from the walkway not flush.

@bigair0176 3 жыл бұрын

The back does not sit flush. I made the rear floor first. I wanted the floor to sit above the rails that run on the floor of the boat. If I cut the notches like I did on the front panel to accommodate the rails I could have dropped it an inch to make flush. Worked out in end cause I don’t trip over my cable for sounder cause it is protected bu the lip now. But if you want it flush cut out the 2 notches on each side to allow the plywood to sit lower.

@baggersvancelegendof835 3 жыл бұрын

Thanks for the help

@dirtydogvideo Жыл бұрын

did you use outdoor/marine linoleum, and how is it holding up? thanks

@bigair0176 Жыл бұрын

Holding up great. I believe I just got it from Home Depot. Nothing special.

@kentyler966 Жыл бұрын

It would seem likely the the linoleum would be dangerously slippery if it was wet? Could you address this issue? I’m not a big fan of carpet but a slippery floor would be a deal breaker? Thanks

@bigair0176 Жыл бұрын

Nah. Floor works awesome. I usually do barefoot as well. No issues

@quasarcom5041 Жыл бұрын

Don’t use treated wood on Aluminum it will eat right through the Aluminum. I used to be a senior executive with a major boat company and we where the largest manufacturer of Aluminum boats. We never used treated wood.

@bigair0176 Жыл бұрын

Good to know. Thx for sharing! Cheers

@cohoman83 3 жыл бұрын

3/8 or 1/2 ply?

@bigair0176 3 жыл бұрын

1/2. Just reg ply.

@cohoman83 3 жыл бұрын

One other quick question ,the frame for the back is just square? Do you know roughly the dimensions of the 2x4s

@bigair0176 3 жыл бұрын

@@cohoman83 yes they are just square. One I believe I cut the 2x4 to match the angle of the boat. The frame I thought I measured as well in the vid. But roughly to my memory was about a foot wide by and then as wide as the panel itself. Just depends on how low or high you want it all to sit. I made mine as close as possible to my walk through seat between both panels

@cohoman83 3 жыл бұрын

@@bigair0176 thanks man I just bought some starboard that I'm going to use for the floor. Never going to deteriorate? Cheers happy fiahing

@bigair0176 3 жыл бұрын

Same to you brotha!