How to modify fsia6b receiver to get battery voltage telemetry

Рет қаралды 37,828

5 жыл бұрын

My rc video playlist
👉 • Rc video playlist
Hello friends today in this video i have shown how to modify flysky fsia6b receiver to get battery voltage telemetry on the transmitter. Normally the receiver voltage shown on the fs-i6 transmitter is the BEC voltage we feed to the receiver. Which is useless as we all know the voltage of a BEC which connected to receiver. But with this modification we can get real-time battery voltage in our transmitter. It will be very helpful if you don't use any external telemetry device.
Please take help from a skilled person if you have bad soldering skill.
Thank you very much for watching
if you have enjoyed this video then please like, share, comment and don't forget to subscribe.

Пікірлер: 48

@anhntcover7971 4 жыл бұрын

Simple, concise, awesome 😆

@HomeDronen 5 жыл бұрын

I appreciate the info...cheers!

@Baz4antify 2 жыл бұрын

Awesome video! Thanks, I'm going to make this modification!

@ashishpawar2261 3 жыл бұрын

Great video, it's working perfectly, thanks for such informative video

@tryingtomake9871 5 жыл бұрын

useful thinks

@PeterAbt 4 жыл бұрын

Do you know if there is any way to turn of the Voltage Alarm? Because when I have my motor on - full throttle the voltage drops down quiet drastically - so low - that the alarm goes off. But I want to keep the high- low-voltage settings so that there I can keep the beautiful battery animation at the top right corner of the display. Besides that: Thank you for the video was a great help and works flawlessly!

@magneresjuan 2 жыл бұрын

Hello ! Great vid. I conect oposite voltage baterry to my fs ia6 receiver AND saw smoke... any ideas for the repair

@Infinitymotivation 5 жыл бұрын

Amazing

@TechIdeasAG 5 жыл бұрын

Thank you

@prabalsingh3622 5 жыл бұрын

Nice Video 👌 But please make a video on monster amplifier... Can you make ?

@rcbuildmaster6192 3 жыл бұрын

Nice info , but I think we get flysky voltage sensor which can connect to ibus sensor port directly on FSIA6B

@yashsoni7137 3 жыл бұрын

It will distroye your rx

@MuhammadTalha-in3ws 4 жыл бұрын

Thanks waho

@dominikap.7399 4 жыл бұрын

What parameters to set on the transmitter for the 11.1V battery? How much for low, high and for alarm? The alarm rings even at full battery.

@marinaartandcraft8662 5 жыл бұрын

Bhai mere pas ek transmeter hai jisme 16mhz crystal laga huaa hai jo programmable nahi hai. Ye kis resiver ke sath binde karega.

@SimjimX0 4 жыл бұрын

Hello nice video How do you cut the wire to the rx fsia6b please?

@feltav5719 Жыл бұрын

After this mod can you still get altitude telemetry as well as the rx voltage?

@harrymoman2682 4 жыл бұрын

is putting wire from charging plug actually putting any extra volts into the reciever , i did this mod and just removed the power cable from my ppm cable and just ran the wire to the charge plug on the single cell , therefore i can use low voltage alarm on my remote , so thats only putting up to 4volts into the reciever , not the 12.6 you are ,,, also the cut and wire mod from the resistor to the cut pin , what is that actually doing as i never did it that way... thanks

@mush0847 3 жыл бұрын

The specification shows 4.2 to 6.5v max, but 11v battery can be used?

@sinongsium193 5 жыл бұрын

sip

@jc_fpv_ec 4 жыл бұрын

function for 4s battery ???

@technoroid 4 жыл бұрын

Hello, do you know what is lowest voltage and highest can be monitored? I plan to use 6S LiPo and want to keep up with voltage monitoring, will it work? Thank you in advance

@TechIdeasAG 4 жыл бұрын

It's just simple, whatever battery you use just use 3s to the receiver, you can easily get it from your battery's charging connector. Hope you understand.

@finleeover 4 жыл бұрын

@@TechIdeasAG Thank you. I understand.

@demodelbouwloods987 Жыл бұрын

how much voltage can it handle? can it handle a 6s battery?

@kickfliph 2 жыл бұрын

Hello there, I'm trying to replicate the mod, so far I have made the cuts for the pin, in the front side, and in the back. But when I measure with the voltmeter I still have continuity, I scraped all that I believe makes the connection to the other pins in line but looks like It's still connected to the others. My board is like your brown color and not green as I see in some others videos posts, is that make any difference? I should do something else for this model/version board for the mod to work?

@hoath99 Жыл бұрын

I think I have the same board as you, at the reverse of the pin, cut right into the corner on both the vertical & horizontal board. When i worked this out it cut continuity for me.

@yashsoni7137 3 жыл бұрын

When i give it power a theer face black ic which placed between two yellow ic is heating too much

@k1ortia 3 жыл бұрын

Just buy the £3 FS-CVT01 Sensor. plug and play in 5 seconds. job done

@DLM517 3 жыл бұрын

THANKS.

@DLM517 3 жыл бұрын

what country coinage is it as my keyboatd doesn't have it, thanks.

@jimstewart6720 2 жыл бұрын

Looks pretty risky......I bought the sensor!

@Typcio22 4 жыл бұрын

Great!:) Are there any problems that this modification can cause?

@yashsoni7137 3 жыл бұрын

Problem nhi pura rx ki ma bhen ek ho jyegi dont try this

@prajvalbs8787 2 жыл бұрын

Will this work for 4s , will it burn on 4s , please reply

@TechIdeasAG 2 жыл бұрын

It'll damage getting very hot

@prajvalbs8787 2 жыл бұрын

Ok tq

@prajvalbs8787 2 жыл бұрын

Can i use 3s

@FliteRC 4 жыл бұрын

Kuch receiver me problem to ni aae gi na

@TechIdeasAG 4 жыл бұрын

No problem, better use 7806 regulator

@melvi8834 3 жыл бұрын

the video is not very good as it does not show at all well where it needs to be cut. I managed to make this change which is not very simple and not for everyone. I repeat the video does not show at all well where to cut in the part below.

@DLM517 3 жыл бұрын

No comment!