Learn how to pour a concrete front porch sidewalk with this DIY Step-by-Step Video. Specifically, learn how to pour a DIY curved concrete sidewalk for a front entryway using dry concrete mix.
To Pour a DIY Concrete Sidewalk, you will need the following tools and materials:
- Concrete Finishing Trowel: amzn.to/3Za9tHu
- Concrete Edging Trowel: amzn.to/3m2KQh5
- Concrete Grooving Trowel: amzn.to/3IDNi5x
- Concrete Finishing Broom: amzn.to/3kIa8kh
- Dry Concrete Mix: www.ctscement.com/product/cts...
- Concrete Mixer: www.mudmixer.com/andrew
- Concrete Forms: Harboard or 2"x4" lumber
- Stakes: amzn.to/3xZMqDb
Below are the General Steps for Pouring a Curved Concrete Front Porch Sidewalk:
1. Demolish the Existing Sidewalk (if applicable)
This video will show you how to demolish an existing concrete sidewalk using a jackhammer.
2. Prepare the Area for New Concrete
Typically, you will want a 4" thick concrete sidewalk and a 4" thick gravel subbase. Excavate the area as needed.
3. Build the Concrete Forms for the Sidewalk
Construct the concrete forms using 2"x4" lumber or Hardboard (ripped down to 4" strips) if you are building a curved sidewalk.
4. Mix up the dry Concrete
For this specific DIY Concrete Project, I used Rapidset's 24/6 Concrete Mix and I Mixed it using the Mud Mixer.
5. Apply Concrete to the Forms and Screed the Concrete Surface Flat
Fill the concrete forms with concrete and then use a flat piece of lumber to screed the surface of the concrete flat.
6. Finish the Surface of the Concrete Sidewalk
Use a concrete finishing trowel to finish the surface of the concrete so that it is smooth and even.
7. Use an Edging trowel to "Round Over" the edges
Run a concrete edging trowel between the edge of the concrete and the forms to give the concrete a nice rounded edge.
8. Add control joints (if applicable)
If you are pouring a large concrete sidewalk, add a control joint with the use of grooving trowel.
9. Apply a Broom Finish to the Concrete Surface
If desired, use a concrete broom to give the surface of the concrete a "broom finish". This will give the concrete a textured look and will make the face of the concrete non-slip.
10. Allow the Concrete to Cure
Let the concrete cure and harden (typically 24-48 hours)
11. Remove the Concrete Forms
After allowing the concrete sidewalk to cure, remove the concrete forms.
This video will explain every step of the concrete sidewalk pouring process from start to finish.
Additionally, check out my blog article for even more information on concrete pouring: atimprovements.com/how-to-pou...
Be sure to subscribe and hit the notification bell so you don't miss any future videos! I have some big plans for the font of the house that I hope will boost the curb appeal!
Follow me on Instagram: / atimprovements
Check out my Blog: Atimprovements.com
Subscribe to my KZfaq Channel ⬇️ kzfaq.info...
Check out my Website for additional DIY Content: atimprovements.com
▬▬▬▬▬▬▬▬▬▬▬▬▬
🎥 MY KZfaq GEAR
Camera (Iphone Max): amzn.to/3d5HxSo
Microphone (Maono Condenser Mic): amzn.to/3RCAb7N
Tripod: amzn.to/3Rz5Gj3
Mini Tripod: amzn.to/3Rvt2WM
Lighting: amzn.to/3d4QdZ5
▬▬▬▬▬▬▬▬▬▬▬▬▬
🛠🧰 TOOLS THAT I USE
Carbide Tipped Drill Bit: amzn.to/3S0hdIM
Tapcon Screws: amzn.to/3OxEWxh
Drill: amzn.to/3JICKkk
Tape Measure: amzn.to/3HaTWgE
Circular Saw: amzn.to/3BFotC4
Masonry Drill: amzn.to/36yP1JW
Level: amzn.to/3HowUDn
Hammer: amzn.to/35fIpiT
Chalk Line: amzn.to/3MwSDg8
Clamps: amzn.to/3HLqwpK
Drill: amzn.to/3JICKkk
Sawzall: amzn.to/3HcdeSI
Circular Saw: amzn.to/3BFotC4
Jig saw: amzn.to/3I6lcyd
Air Compressor: amzn.to/34TatJf
Framing Nailer: amzn.to/3JGpBYU
Roofing Nailer: amzn.to/3BEAuYF
Orbital Sander: amzn.to/34UwlUD
Bar Clamps: amzn.to/3JjFrJe
▬▬▬▬▬▬▬▬▬▬▬▬▬
Thank you so much for watching!
*All content on the Andrew Thron Improvements KZfaq channel reflects my own opinions. Please seek out guidance of professionally trained and licensed individuals before making any decisions. Links in the description may be affiliate links.