How to Print LW-PLA (ALL MY SETTINGS)

How to Print LW-PLA (ALL MY SETTINGS) | ft. NEW eSun eLW-PLA

Рет қаралды 132,010

Күн бұрын

I will show you every line in Cura for all my LW-PLA settings. To print PLA just change the temp to 215c and 100% Flow rates. I will also show the difference between ColorFabb LW-PLA and eSun eLW-PLA.
Thank you so much for watching!
Propeller Wall Art: cults3d.com/en/3d-model/art/p...
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmi...
See what else I am working on: / troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #ItFlies
ColorFabb LW-PLA: colorfabb.com/lw-pla-natural
eSun ePLA-LW: Coming Soon
Plane Print Notes: www.planeprint.com/notos
LW-PLA Setting
Profile 3 Cura:
Quality:
Layer Height - 0.25
Line Width - 0.4
Shell:
Wall Line Count - 1
Infill:
Infill Density - 0
Material:
Printing Temperature - 235
Build Plate Temperature - 60
Flow - 55%
Enable Retraction - Checked
Retraction Distance - 2
Retraction Speed - 30
Retraction Extra Prime Amount - 0.5
Speed:
Print Speed - 100
Outer Wall Speed - 40
Inner Wall Speed - 40
Travel Speed - 80
Travel:
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 20
Mesh Fixes:
Union Overlapping Volumes - NOT Checked
Special Modes:
Surface Mode - Surface
Experimental:
Slicing Tolerance - Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!

Пікірлер: 220

@carlosperez7015 2 жыл бұрын

Troy, I received a roll of the Colorfabb today. Your settings have been spot on for every part I've printed. Almost half way and going strong. Thank you so much for sharing!

@andrewjamez 3 жыл бұрын

Great to know eSun do it now. Also to note that Esun have bought out their ST-PLA (Super Strong) Same weight as pla but it has properties that feel more like an HDPE plastic bottle. The specs show as inferior to pla EXCEPT that the sheer strength, Layer adhesion and mailability are more than double that of regular pla. This should be a game changer for rc aircraft where increased strength is nessesary.

@RandyScott-cd4ju 3 ай бұрын

This was a great tutorial! I just started using the active foaming instead of pre-foamed. It got me really close to where I needed to be for my Neptune 4 Plus. I have been an avid RC aircraft guy for roughly 25 years now and I am having fun printing out, designing, and modifying planes.

@theodorenickel7462 2 жыл бұрын

Great video Troy. It is tough for noobs to get it right without help in the beginning. A note to inexperienced 3d printer users, not all filaments are made the same. I bought some Inland LW-PLA that gave beautiful models but the walls were .34mm thick, quite tough but very flimsy. Finely got the E-Sun LW-PLA and - bam - great parts right off. .51mm thick and weight was right on spec. I got a CR 10 V3 with the glass bed. Found that gluestick works great if you put a bit on and use a little rubbing alcohol and paper towel to smear it all over the bed real thin. Locks those parts down really well and a little bump and they pop off without damage every time. No more prying and digging. Hope you enjoy the coffee I sent last week.

@marckcl23 2 ай бұрын

Hola. Bajé CURA, pero no me sale el filamento LW PLA... O tiene otro nombre en Cura???.... Gracias

@paulocallaghan8303 2 жыл бұрын

Thx for this Troy - just received my ESun LW-PLA and was strugglin but these worked a treat!! Awesome

@knowledgebyte 2 ай бұрын

Thanks again for posting this. I have a model I bought years ago from 3DLabs, the Swift S1. It's a mare to print, especially F_2.STL, as you need Cura 4.8 and 'filter tiny gaps' for the PLA parts due to the way the mesh has been rendered. Fast forwad 4 years and now we have Eclipson and 3DLabs knocking out some beautiful designs.

@colsoyeti1 3 жыл бұрын

Thanks for the comparison tests, it is good to see that more options are becoming available and this will make LW-PLA more affordable. A request if I may, would you be able to do a short video on paints in the near future? I think an explanation on paints and the pros and cons associated to weights and flight is something most of your viewers would be interested in. When I watch your videos as mentioned before I get very inspired and find my creative juices flowing with ideas of what I can do and sometimes the ideas get too carried away....... keep up the good content that keeps us dreaming and building!

@Moonsauc3 2 жыл бұрын

I'd recommend water based paint out of an airbrush then some sort of polyurethane clear coat. But in the past I just use rattle can

@richardcjoy 3 жыл бұрын

The slicer settings seem to be the most challenging so thanks for posting this video. You did mention that the only change for Eclipson planes is to leave Surface mode as Normal but after comparing the settings line by line with those recommend by Eclipson's A-LW profile (imported into Cura from their g-code files) I see quite a few differences and wasn't sure which one to use. I guess I could try both.

@TroyMcMillan 3 жыл бұрын

Depends on the material you are printing out with!

@ShahriarFarkhan Жыл бұрын

This was awesome. I'm printing my Eclipson A with eSun eLW-PLA and your setting are making the parts perfect. Thank you!

@marckcl23 2 ай бұрын

Hola. Bajé CURA, pero no me sale el filamento LW PLA... O tiene otro nombre en Cura???.... Gracias

@rickf9243 6 ай бұрын

Troy, nice videos,, I was struggling with the LW PLA settings. Now having the correct settings is huge, it works great now,, thank you for sharing.

@user-md6oz7jc6w 11 ай бұрын

Thanks Troy, These settings are resulting in very clean prints.

@justbill62 3 жыл бұрын

Damn nice job, thanks for all the work.

@tala23ful 2 жыл бұрын

Great information thanks to your videos I have had success in printing several planes and now with the eSun LW-PLA I have finished the Plane Print Rise. Without your info I would be still printing test pieces and scratching my head what to try next. Thanks again, look forward to your next project. Might have to try the Eagle next.

@Chilternflyer 3 жыл бұрын

Thanks for posting this. I've just started on my Planeprint Eagle and haven't got to the LW PLA parts yet.

@dzisow 2 жыл бұрын

Hi Troy. Thanks for all your wonderful instructional videos. I have found one problem worth noting. I am using an Ender 7. I have been working with the Eclipson Pitts (you demonstrated the build in a different video) and found that in spite of all the settings you have shown in this video, there is a G-code command M106 (sometimes more than one) in the G-code created by slicing the Epsilon STL files. These M106 codes are also in the G-codes Epsilon offers in their download too. Regardless, unless I edit out those M106 codes before printing, the nozzle temp drops precipitously to the point where the printing stops due to a heating error. That said, as long as I edit out those M106 codes from the sliced file using your slicer setup, the printing results are excellent.

@Canal_do_Kirby 2 жыл бұрын

You have a lot valious information in your channel. I did my first Zero A6m, follow your tips. I have two Zero now (Zero ABS/PLA 800g total weight and Zero PLA-LW ~500g). Keep your great job.

@rcdavidk 3 жыл бұрын

Thanks for showing the same sliced part printed on 3 different printers. That's the only area I worry about regarding settings. Your settings work great on your printer, but may not work as well on my different printer. Your showing the same part across 3 printers is significant. Cheers.

@hermann-josefchrist1846 3 жыл бұрын

Hello, thank you for the helpful video. Keep it up. All the best! Hermann

@Johnellenberger1 Жыл бұрын

Great video Troy! Your settings are perfect for my Ender 3 with the Micro Swiss Direct drive and using Sainsmart LW PLA. The only difference was the temps because of the Sainsmart LW PLA.

@joewynn2445 Жыл бұрын

Thank you so much, i tried to do everything that i could think of to get my eSun LW-PLA to print and it just kept clogging and i couldnt get past just the base layer. Im no pro when it comes to 3d printing and ive only had my 3d printer for a few months and only printed with PLA+. You truly helped me out tremendously. Onto printing my F16 now. 😁

@motionsiik4964 3 жыл бұрын

Thank you for all your videos! This one was SUPER helpful PRO TIP: watch in 50% speed in settings so you can follow along in CURA

@MikkoRantalainen 2 жыл бұрын

If you pause youtube video, you can advance one frame with full stop (.) and referse one frame with comma (,). Cursor left/right skips 5 seconds and letters J, K, L skip 10 sec backwards, pause and skip 10 secs forward.

@MattGratt 2 жыл бұрын

I used these settings for the Planes Print Eagle LW PLA parts and it solved the problems I was having. The Planes Print suggested settings produced a scorched mess full of holes on my Anycubic Vyper

@lio1234234 3 жыл бұрын

I love Esun, so happy to hear they are doing their own light weight PLA!

@TroyMcMillan 3 жыл бұрын

Me too!

@WIZARDDETECTIVE 5 ай бұрын

I’m interested in printing a plane and your videos are the first I’ve heard of LW PLA

@GregFurtman 2 жыл бұрын

Troy, another great video. I have learned more from you about Cura & 3D printing than from any other source. Thank you. One of the things I'd like to see you do is setting up Cura. What fields need to be made visible in Setting Visibility? I've also noticed that at times you show the extruder and the nozzle path. How is this done? And I've seen animation controls along the bottom of your screen is some of your videos. I have only a vertical scroll bar along the right edge of the screen for going to different layers. Is the animation controls & nozzle visibility something that needs to be turned on somewhere in Preferences? A plug in? Thanks.

@en13445 3 жыл бұрын

Another great video! It would be really interesting to see a comparison video of your 3d printers. Do you have a favorite printer so far for printing thin wall airplane parts?

@williammann9007 3 жыл бұрын

You are awesome my friend!

@TroyMcMillan 3 жыл бұрын

Thank you!!

@bobp5356 Жыл бұрын

Great video. Lots of good info.

@MikkoRantalainen 2 жыл бұрын

Could you do strength testing with different LW-PLA filaments? For normal 3D printing you can usually improve the strength a bit by increasing the temperature but it seems that LW-PLA is really finicky with the temperature so that cheat cannot probably be used here.

@SILVIOFRANCO1 3 жыл бұрын

A great video. I learned a lot. Thanks

@TroyMcMillan 3 жыл бұрын

So happy I could help!!

@enricovolante 2 жыл бұрын

Thanks Troy for the video. I didn’t quite get how you select minimum extruder travel in cura, I just understood it’s a new feature. Would you be so nice to share with us? Congrats for the amazing channel and btw, I love the airliner ))

@pierre3036 Жыл бұрын

I have the same question? Very poorly explained.

@kmi3dprint 3 жыл бұрын

This is great. Thank you for this! I have been following your Eclipson prints and have printed many of their plans with their gcodes. Will be nice to chagne them up a bit. I am curious what you are doing with the different Eclipson settings. I assume these work with the A-LW. Do you leave most of this the same for the C-LW as well; like the flow, speed, etc? What do you change for this setting?

@mammolese2002 2 жыл бұрын

Finally something that I needed to know. That’s that Ender is capable of printing plane’s parts.

@albertdrew7235 3 жыл бұрын

Thanks Troy, thats what I've been waiting for !! What printer are you using these settingsom?

@bobharris7458 5 ай бұрын

Dude! Great videos you make! I'm going to make the Longboard 1000. It should be fun project. I love it!

@NICHOLASRGLORIOSO 3 жыл бұрын

Cool man!!

@gordonendicott5114 Ай бұрын

Really appreciate you list your settings that really helps

@typicalhike8219 Жыл бұрын

Thank you so much you have helped along with the printing. Sadly tho we have no idea how to make it so that we can have infill on the modal to help support the airfoil skilll

@DjArity 2 жыл бұрын

Thank you for posting this really informative vide on light weight filament. Was wondering if you could help out with the eclipson settings on a VoxMaker slicer software. Some of the setting are not the same or it's different and sometimes get lost trying to transpose the settings between what you have on this video. Thanks in advance.

@klausrimdoi45 Жыл бұрын

Hi Troy, your video are very informative ... thank you for it. It works like a charm on an S1 Pro direct drive. Question: would this LW-PLA profile work the same on a bowden 3 V3 ?

@76aussieguy 2 жыл бұрын

nice vid mate

@key0neek 2 жыл бұрын

Hey Troy Awesome Vids... Learned a lot from watching... Maybe one day Ill run into you at one of the flying sites as I live Vegas too... I've been using your settings in a couple of your vids to get started on an Eclipson Model S. while your print settings are nearly perfect, my prints come out with highly visible seams where the print head transitions from printing internal structure to printing the thinwall "skin". On Eclipson's models, thats mainly on the bottom of the wings. Could you point me to the settings that might help with this?? Thanks again

@franknieves2739 3 жыл бұрын

Great instructional videos Troy, I've learned a lot from them. In this vid you mention how to get rid of stringing printing LW PLA. Which is the newer method that you mentioned? My LW PLA test wing from Plane Print still has stringing issues.

@TroyMcMillan 3 жыл бұрын

You can't print the test part out with no stringing. Try printing out one of the parts from a plane that is designed for lw pla printing!

@Miniellipse 2 жыл бұрын

@@TroyMcMillan CAn you elaborate? Is there a slicer setting to activate so that the head moves without stopping (as briefly shown in your video). I have a PRusa Mk3.

@underengineered_1077 2 жыл бұрын

hi, i'm new to plane printing and i'm using this guide to set up my esun-lw roll (first time using it). I didn't quite understand what you are saying at 4:56 regarding the new printing method. Is it a specific profile setup or is it referring to how the plane is designed? I use simplify, so i'm sure i'll have to play around with my settings, regardless.

@IfItFlies-yg9ct Жыл бұрын

Thanks troy. Just one small point... slow down when scrolling through your settings on the screen. I keep having to replay sections over and over just to make sure I have not missed anything.

@roberteicke2540 3 ай бұрын

I changed the youtube speed to 25% so i could read his settings.

@user-jm1bl6qx8x 2 жыл бұрын

THANK YOU!

@joshlikessurfing 3 жыл бұрын

This is such a good video! Would be interested if you came across a setting guide for prusa slicer.

@TroyMcMillan 3 жыл бұрын

I have to get a prusa first!

@pnh555 Жыл бұрын

Thanks Troy this video saved me days of fiddling with cura. Do you know if there is a seaplane model like an icon available to print?

@joexie6834 2 жыл бұрын

Troy, thank you for the video.what was the method to get rid of string problem. sorry I don't understand this part.

@christianlainesse4281 3 жыл бұрын

Have you tried using a larger nozzle to print LW PLA faster and bigger?

@user-wb8qv4fp2j 4 ай бұрын

Have to say a big than you mate. These settings with very little tweaking were superb for my prusa mk3

@luisdelarosa7609 Жыл бұрын

Great video, I wonder what is the wall thickness you use in the 3D model? Thanks

@aviator_123 3 жыл бұрын

Отлично!👍🔥

@arpia47 3 жыл бұрын

Thank you master

@brianwendel2528 2 жыл бұрын

Hi Troy. Just ordered esun LW Pla. My pla prints come out great using your profiles, however they are heavier than expected. Is this due to flow rate or another setting? Thanks

@coultl6556 8 ай бұрын

So helpful! Will these Cura settings work for 3D Lab Print planes?

@sotm6078 3 жыл бұрын

I just saved my P3 profile as P3-LW with the LW changes. That way you can choose which one you need.

@TroyMcMillan 3 жыл бұрын

That is a good idea!

@martulda 2 жыл бұрын

HIi and thanks for infos on cura settings for LW printing... Cool but touchy the right difference with std PLA... Watch out, my plane have guiding tubes for link servos to tail -LW will shrink these hole's dia- and squatching the steel piano wires what now???

@SniperUSMC 2 жыл бұрын

Awesome, what kind of printer are you using? How much did it cost to print this aircraft with LW PLA, was there a significant price difference in printing the same aircraft with Colorfast vs Esun? Are there any FPV aircraft that can be printed with LW PLA? How about strength of the LW PLA, strong enough to mount gimbled camera's? Thanks!

@Frank-ft3lb 2 жыл бұрын

I used your LW-PLA settings and of all the setting I've tried they produce the best results. I'm getting the thinnest walls. I still have one problem I have not solved and that is I still get pimples all over the print. In one airframe section I printed it has tubes for graphite rod support and the tubes have pimples in it so I can't insert a graphite rod. Any ideas on what I could try to eliminate these pimples? The stringy issues I had are gone! BTW When I print with regular PLA and the standard CURA profile I get good quality prints with out pimples or stringing.

@starletzzang 2 жыл бұрын

Are the lw-pla wings more resilient compared to PLA when they fall to the floor or are pressed with your fingers? I made it out of PLA, but when it breaks, it breaks easily. Is lw-pla stronger than pla? Or is it similar? I wonder lw-pla is more expensive. here in Korea.

@paul-ballard 2 жыл бұрын

Hi Troy, have you found any difference in strength between ESun and Colorfab?

@Vipcioo 3 жыл бұрын

Printing R / C models is very tempting. However, I see two serious drawbacks: - filament price. Currently, 1kg is over £ 40, meaning the larger models will be worth hundreds of pounds - temperature resistance. I'm afraid that in summer the model can easily distort from the sun Have you had any experience with this?

@peterberggreen7647 3 жыл бұрын

Hi Troy - I have seen a lot of your videos, and will try to print the eagle but somehow I don't have all the options and settings in my version of Cura 4.10. I use MAC and can't find a version that just look a little like your settings - so what do I do?

@surveyorna1658 2 жыл бұрын

Troy, thanks for your videos, I am printing the Notos, is it better to print one item at a time or multiple files? Or does it matter?

@stefanraghavan1622 2 жыл бұрын

Any notable difference in surface finish between regular PLA and colorfabb LW PLA?

@fernandoperez8911 Жыл бұрын

Thank you for the video. I have a 3d model airplane and want to design as you. Where can I read about your print design system (which eliminates internal passes)?

@jonathanwhitaker2806 Жыл бұрын

Troy, what version of Cura you do use in your videos? I've seen a lot of discussions about Cura 5.3.1 (latest as of this post) having issues compared to the prior 4.12 and 4.13 releases. Do you have a recommendation?

@sanjoydas007 2 жыл бұрын

What printer would you suggest if my work involves only working with light weight PLA, that too for small parts ?

@brian26339 Жыл бұрын

Noob 3d printer here. I have a FLsun v400 delta printer. If I wanted to take advantage of its speed, can I just raise the print and travel speed settings or will I run into other issues by trying to speed it up? The LW Pla prints so different from regular PLA and I’m trying to not waste too much of the LW stuff because colorfab is kinda pricey. Will have to try ESun. Thanks for the help!

@johnoriente498 Жыл бұрын

How do I get the wall thickness to increase. I printed a test box from 230 to 270 in 10 degree increments and really didn’t see a an big difference. Printing on a Anycubic Kobra direct drive. I printed a plane from 3d lab print. The weight of each piece was correct but the walls were thin by 1/2. It’s almost paper like rather than plastic. Any help is greatly appreciated

@antonisvianos8017 Жыл бұрын

Hi Troy. I'm trying to print colorfabb Varioshore TPU (tyres for my Hurricane) with my printer CR6 SE which have divert to direct drive extruder with LGX and Mosquito Hotend but can't find any profile for cura or creality. Extruder works perfect due print BLERIOT and is perfect.

@dragonslayer5702 8 ай бұрын

You’re a cool guy Troy, nice info 🐐

@leenanipun1269 23 күн бұрын

Thank you for the video - do you also have settings for prefoamed lw pla like polylite lw pla?

@esmithjm 2 жыл бұрын

What wall thickness did you design your test cube? thanks

@ollih5562 2 жыл бұрын

Hello, I have problems with the stringing. At cruising speed I always get it with retract or without. I use the prusalicer but the settings are almost the same. in vase mode there is almost no cruising speed. and also no stringing. but in some prints you need closed top and bottom. On the wing where the ailerons are, the wing edge is always open, which is bad. I print that in normal mode, all settings the same but without vase mode, just 1 perimeter. How do you do it, or you Troy? Lw PLA ColorFAbb

@RCPlaneAddict 2 жыл бұрын

Troy, another solid video. Thanks for sharing. I still cannot wrap my head around the cost of LW PLA but, I suppose the weight is what you are paying for. About how much material do you find you use per plane? I know this is a difficult question as all planes are different, but lets use the Panthera for example.

@MilitiaMan22 2 жыл бұрын

It expands to twice it's original size so it like having 2 kilos of filament in volume so half the price and you get a better idea of value

@teachergabrielmaia Жыл бұрын

Hi Troy, I'm trying to print the 3dlabprint piper using these configs but the control horns are not being printed. it only prints the outline. I tried to chang the top/botton configs but it didn't work. What should I do to print it correctly?

@englecam 3 жыл бұрын

Good job troy. I 'll get a try with esun

@TroyMcMillan 3 жыл бұрын

I recommend it!

@cadydiditcustoms6654 3 жыл бұрын

It doesn't seem to be available anywhere though?

@TroyMcMillan 3 жыл бұрын

@@cadydiditcustoms6654 they are out of stock at the moment, hopefully should be stocking this next month sometime!

@cadydiditcustoms6654 3 жыл бұрын

@@TroyMcMillan I just got my first roll of Colorfabb LW-PLA, and I am now looking for a good airframe to jump into, hopefully something that can fly on an F-pack from Flite Test...

@TroyMcMillan 3 жыл бұрын

@@cadydiditcustoms6654 Im not sure what the f pack is, but a good first plane would be the model v by eclipson easy to print and flies very good, a great beginner plane

@willasproth 3 жыл бұрын

Thanks fam

@TroyMcMillan 3 жыл бұрын

Hope it helps 🤞

@rickwentworth6842 2 ай бұрын

Any thoughts about using pre-foamed polymaker LW-PLA?

@jimmy2times 3 жыл бұрын

When flying the airplanes, dp you ever get cracks along the layer lines say in the wings because of such a thin wall? I mean when the surfaces slightly bend due to maneuver induced or load stress?

@TroyMcMillan 3 жыл бұрын

No I haven't experienced that! It has a little flex to it, so it would probably have to be a pretty extreme situation

@renlis01 2 жыл бұрын

Hi Troy... I Just made that test wing from plane print with lw pla (esun) but I looks like significantly softer than The regular pla. Is that expected??

@adamflight1 3 жыл бұрын

Another great video Troy. Thank you for all the detail and the help in the settings. I just ordered some lightweight pla. I noticed that sometimes you do use regular pla, is that only for areas of the plane that is needing the extra structural support? Thanks again.

@TroyMcMillan 3 жыл бұрын

I appreciate that! I hope it helps! Yeah, the regular PLA is used for strength. The best use of LW-PLA is definitely in a hybrid system.

@markvios29 2 жыл бұрын

Have you heard anything about polymaker light weight pla? I bought a roll and will see how it does.

@FATSNAIL-FPV 3 жыл бұрын

Saw some lines in the Esun LW-pl: just some minor artifacts because of no esun specific settings, or did it crack? chilled and informative video as always!

@TroyMcMillan 3 жыл бұрын

I had to turn the flow rates up a little more, but ya that one piece didn't print great.

@robblackadder5405 Жыл бұрын

Hi Troy, Have you ever done the same eSun LW-PLA Vid for PuraSlicer ?

@BruceEwell Ай бұрын

Im really struggling with lw-PLA from eSun bottom layers are spot on but as it gets about half way I am getting ribs on the outside of the layers not sure what is causing this ( using a ender 3 v3 se with cura )

@stevelong8679 2 жыл бұрын

Hi got your airbus but having problems with fus sizeing can you please help me

@TheTechMaverick 7 ай бұрын

Everything works with the settings on mine except it keeps making a squiggly line down one side. It does not do this on the other side. Do you know why it is doing this? I am printing with an Ender 3 Max.

@dericklong6191 5 ай бұрын

I got the Overture lightweight pla and tried several times but your settings but then I realized this lightweight pla is pre- foamed. So I keep pre foamed set to 100% flow rate?

@dennissumnerdsumner4804 Жыл бұрын

What release Cura are these settings for? I am using 5.3.1, the settings in your video seem to work fine. Thnx

@leeo.alexander2324 2 жыл бұрын

I see that you have an SWX1. I have the same printer and also a FLSUN Q5. Hopefully, I can complete my FLSUN QQ-S Pro(Hybrid) before the end of June. I have designed and 3d printed parts for the QQ-S Pro. What profile are you using on the X1? I have S3D and Cura 4.13.1. None of the beta 5 versions will load and I have not found out why yet. I have a friend who is an RC flyer and a builder, and we are looking at collaborating on one of these builds. He is very interested in the 3d build, but does not own a printer and has never designed parts for one. His background is in aviation since he flew cargo planes during the Vietnam conflict. I have to adjust my budget to get the LW-PLA to calibrate both printers. This filament is not cheap.

@fyzobaba 3 жыл бұрын

Great video again.but it's funny most people don't talk about how this pla shatters if u make any mistake on landing.after all the hard work n time putting the planes together then one second mistake it's over.