Expectations 0:01 vs reality 0:08

would i be able to print the tail wing as a hole on a 8inx8inx8in 3d printer

I want a airplane

What happens if you dont remove the wire in the middle?

What glue do you use?

Did this thing crash immediately? No video of the flight at all?

Damn.. You handled that well, but I could tell it hurt bad. I know this is an old video and it looks like you repaired since, but damn... sorry for your loss! >.<

now add a sound box so if it disconnects it play the terrain sound

Use a shit radio system

The crash looked so realistic, like a real airplane crash

Hello, good evening, I wanted to know the positioning to print the front cover where the camera goes, all attempts were bad

Can you make a spitfire

Мотор не перегревается?

CAN YOU MAKE BOENG 747 in germany please 🙏🙏🙏🙏🙏

Awesome job sir! Would you consider a war plane? Not many have done an HE111

ur so good at building ur videos are cool (the crashes are sad)

you should make a airless basketball

WOW!!! Las Vegas?? Where did the Jungle north of the runway go?!!?

Do you happen to have the rear wheel model? Just got a 3d printer and almost finished this thing plane. Thanks for the video!!

to each their own, but that "notch" is called a detent and it's has a purpose. I personally like knowing when I'm at 50% power if using forward only or 0% if using full range. Great HOTAS BTW I have the TMH One

I have this plane and it fly nicely with FPV. I would recommend to put a little bigger rear wheel if you plan to start from grass or broken concrete.

Bro why does plane look like me after building 😭😭😭

Is it OK to heat gun thr parts together? How well does the glue hold up?

Where is Troy at? This is the last video he's put up and it's over a year old. I see a lot of people are still buying and downloading his files but there's no support. I don't understand how KZfaq can let this go on and leave his channel up. I would like to purchase so files from him to print but I'm really weary about it. Please, let me know if anyone has any info on this.

Air Crash Investigation :- Damage to fuselage, enginesm Wings broken, landing gear far away, weather was clear.

Very nice

Aren't you worried the sun is going to warp it. I just got the model because of your video, but PLA...hmmmm

That's nice plane 🎉

Sir do you have instagram cause I want to talk to you plzzzz

Sir do you have instagram cause I want to talk to you plzzzz

Showw

Nice videos. I decided to try this out using Polymaker LW-PLA prefoamed filament. It printed 15% lighter than PLA. It printed very nicely. I imported the mk3 files into Prussa slicer. My Fuse sections all have solid bulkheads wth holes for the wires and control rods. It seems they should be open as pictued in your prints and fit together with a lip. What might be wrong?

Can I use normal PLA filament or would it be heavier

What type of filament did you use? Can I use ABS?

I have subscribed to several channels looking for the following help on the following Ender 3pro gantry sits at an angle 38mm extruder side and 44mm on dual zrod side. Anyone? Been working on this looking for answer over a couple of months. i took apart the dual rod a couple of times same problem. Thanks

Such a shame you were flying well.

Beautiful job and conversion! Thanks for sharing!

As a beginner, I wanted to say thank you very much for showing me how much this works

How did you crash, two 727’s and an a321 like bro

Can you make an atr 72

Very Nice , How much it cost to build on 3D print excluding the electronics?

😉so where you going to sell them😏 Also can you make a atr 72?

Watching him make the plane:😮 I want to make that too! Price:yeah let’s see how you get through that…

a321 and 757 hybrid?

What is the filament?

crappy regional jet--> cool regional jet

thanks for the video, yes I encountered a problem... one engine starts before the other.

Where did you get the files?

I fly rc planes and just got started on 3d printing. I found your channel and have been binge watching your videos. I really want to make these planes and fly them. I have a Creality ender-3 v3 ke, is this printer capable of making these planes? Thanks for any help and great videos!!!!!!!

Why don't you just use DC motor?