How to Program BFT Gate Barrier Remotes

No video

How to Program BFT Gate Barrier Remotes | 2021

Рет қаралды 33,893

AL SUBHAN MEDIA

Күн бұрын

BFT Gate Barrier:
in this video i explained Practically how you can program Remotes of BFT Gate Barrier.

Пікірлер: 50

@vidmantasmilius4608 4 ай бұрын

Great video, worked for me perfectly 👍🏻

@alsubhanmedia 4 ай бұрын

My pleasure🥰

@navindersingh2659 6 күн бұрын

👍👍 good job brother

@alsubhanmedia 6 күн бұрын

Thank you brother

@navindersingh2659 2 күн бұрын

@@alsubhanmedia brother u suggesting in one another video regarding coping codes from remote to remote that trick not working

@alsubhanmedia 2 күн бұрын

@navindersingh2659 it works brother, but a little bit tricky

@navindersingh2659 2 күн бұрын

@@alsubhanmedia can u tell us brother

@faizanabbasi2480 2 жыл бұрын

Great job

@alsubhanmedia 2 жыл бұрын

Thank you

@vidmantasmilius4608 4 ай бұрын

I have another question, after installation the gates foto sensors are not stopping the gate, but I can hear a clicking sound in them, but gates are continuing to move and won't stop, any recommendations wht9can be done to fix that? Cheers!

@alsubhanmedia 4 ай бұрын

Yes photosensor is working fine, but board in not receiving signal sent by photosensor, so it seems wrong connection, short the safety device terminals on board, if it works then connect photosensor wires at same terminals, hope it will solve problem

@renatod.9615 3 ай бұрын

removed the short wire from connector 70 to 72 it will work . Hope it helps you

@alsubhanmedia 3 ай бұрын

@renatod.9615 thanks for sharing the information

@hashimayar233 3 жыл бұрын

Thanks for the good information How many remote is possible?

@alsubhanmedia 3 жыл бұрын

128 Remotes With Clonix, without clonix around 45 Remotes are possible

@javier.ignacioo Жыл бұрын

Thank you !!

@alsubhanmedia Жыл бұрын

You are welcome

@javidiqbal7433 3 жыл бұрын

Very nice

@alsubhanmedia 3 жыл бұрын

Thank you👍

@hanifsiraj7908 Жыл бұрын

veray nice brother

@alsubhanmedia Жыл бұрын

Thank you brother

@hanifsiraj7908 Жыл бұрын

@@alsubhanmedia bro please one video for led light, i was sow in your page but that is not full video

@alsubhanmedia Жыл бұрын

@@hanifsiraj7908 what kind of issue you are facing with LED lights, it is just connection on board and finxing on the Arm/Boom of barrier

@hanifsiraj7908 Жыл бұрын

@@alsubhanmedia brother i am facing the two much down, how can i adjust speed setting,

@alsubhanmedia Жыл бұрын

Brother i have explained i the video about how to adjust the speed, you said you facing too much down then you need to adjust the stop limit with LN key that comes with the new barrier, or if you want to adjust the speed, there is a apeed switch on the board, adjust from there, also download manual/book for this barrier and read the instructions.i hope you got it

@movtc6622 Жыл бұрын

can i use different remote to program it to open the door ?

@alsubhanmedia Жыл бұрын

Yes possible try

@JKV1991 3 жыл бұрын

Thanks

@alsubhanmedia 3 жыл бұрын

Welcome brother👍

@aziz70292 2 жыл бұрын

👍

@rasheed4296 3 жыл бұрын

Same barrier in my office but it's close automatically, how to set manual on/off

@alsubhanmedia 3 жыл бұрын

A key is used to close and open manually, on the barrier body there is a key hole, insert key in it, by rotating the key you can open, close and lock the barrier arm. Hope my reply help you👍

@rasheed4296 3 жыл бұрын

@@alsubhanmedia could I Access manually in remote?

@alsubhanmedia 3 жыл бұрын

@@rasheed4296 yes with remote you can open & close the barrier also

@jamalmohideen9317 2 жыл бұрын

How to set automatically open and close