Elmeasure provides you with energy saving strategies, helping minimize cost and consumption and has emerged as beacon for energy consumers of the 21st century.
Пікірлер: 22
@firstlast11253 күн бұрын
Generator delay should start from 0 sec.
@skk2332 жыл бұрын
Can it be programmed such that whenever EB current(amps) exceeds 10 amps then it automatically switches to Generator. In my case i would connect EB supply to solar and Gen supply to EB so that whenever solar load reaches 10 amps then the load is automatically transferred to EB.
@goat464 Жыл бұрын
It's working in the above method?, And if the current comes down again it will work in solar inverter
@pankajsrivastava44013 жыл бұрын
Hindi bhasa me batayenge iski programing
@ElMeasureIndiaPvtLtdOfficial3 жыл бұрын
Programming video for 1Ph 32A ACCL (with Display version)
@ssgce20062 жыл бұрын
Purchased the same model through Amazon and display not working. Received defective Material and requested for replacement and again received item also display not working. Unable to understand why through online sending defective Material ???
@ElMeasureIndiaPvtLtdOfficial2 жыл бұрын
We apologize for the inconvenience and wish to assure you that we are not sending any defective products to our customers. In fact, The Elmeasure 32A 1Ph ACCL Display will work only on DG mode, EB mode its in off condition. This information is also mentioned in the description section on Amazon. Anyways if you need further clarification about technical features kindly contact us at our toll-free number or email us at support@elmeasure.com.
@apnachannel28563 жыл бұрын
This change over sow the voltage on display in both condition AC or DC
@apnachannel28563 жыл бұрын
Iske display AC aur DC donon se chalu rahegi donon ke voltage show Karega
@ChamanKheuta2 жыл бұрын
Iaccl m400 display work in both mode eb and dg??
@apnachannel28563 жыл бұрын
Bhai yah kitne volt adjust kar sakta hai
@bskestates10 ай бұрын
For EB power there is only phase For Generator There is Phase and Neutral are there For Load Phase and Neutral are there Is this connection ok ? For IACCL 400 Please reply
@ElMeasureIndiaPvtLtdOfficial8 ай бұрын
For EB also Neutral is required
@suhailkhandelhvi9289 ай бұрын
Mujhe reading leni to Kiya karna hoga
@ElMeasureIndiaPvtLtdOfficial8 ай бұрын
Scroll pages using up or down button, pages having only digits is energy reading. EB or DG LED's will indicate to differentiate.
@uppalapatisatyasaibaba20123 жыл бұрын
Good
@poornachandratejasvi2 жыл бұрын
Can I know where is com port or rs485 port ?
@ElMeasureIndiaPvtLtdOfficial2 жыл бұрын
RS485 & com port both are same
@poornachandratejasvi2 жыл бұрын
@@ElMeasureIndiaPvtLtdOfficial I'm not able to find a place holder to connect to rs485
@binnyandrews63712 жыл бұрын
Bought one through Amazon. Display not working .. tried both eb and dg... no display.... Asked for a replacement... if that too not working... refund is the option.
@ElMeasureIndiaPvtLtdOfficial2 жыл бұрын
please let us know if any problem with the replaced device. connect with us on 9137379999 or info@elmeasure.com