How to Set Up a Garage Workshop | Ask This Old House

Рет қаралды 3,134,966

7 жыл бұрын

Ask This Old House general contractor Tom Silva heads to Chicago to transform a garage into a woodworking shop.
SUBSCRIBE to This Old House: bit.ly/SubscribeThisOldHouse
Cost: $2,000-3,000
Skill Level: Moderate
Tools:
Miter saw [amzn.to/2Jt4jlW]
Table saw [amzn.to/2LBcPSC]
Drill/driver [amzn.to/302tbH0]
Sander [amzn.to/2vteHBZ]
Planer [amzn.to/2JedQOr]
Jig saw [amzn.to/30alK0i]
Pocket hole jig [amzn.to/2LDdAdM]
Shopping List:
2x4 lumber [amzn.to/2PSmBOu]
Sheet of _” birch plywood [amzn.to/309zb0D]
Window fan [amzn.to/2W0bx7m]
J hooks [amzn.to/2YiVtex]
Table saw stand [amzn.to/2HebKvG]
Steps:
1. For the folding workbench, build a frame out of 2x4 lumber approximately 4 feet long by 3 feet wide. Include two additional 2x4s for center supports.
2. Attach a 2x4 leger to the long side of the workbench using hinges. This leger will screw into the wall.
3. If you’re also using the workbench as an outfeed table, it should be slightly lower than the top of your table saw. Once you know that height, cut two 2x4s to serve as legs and attach them to the inside of the front of the frame using hinges.
4. Use a masonry drill bit and concrete screws to fasten the leger of the folding workbench to the wall.
Cut _” plywood for the bench top, and allow 1 1/2-2” around three sides for an overhang for clamping. Attach the workbench top to the frame by countersinking screws.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers-and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldHouseFB
Twitter: bit.ly/ThisOldHouseTwitter
bit.ly/AskTOHTwitter
Pinterest: bit.ly/ThisOldHousePinterest
Instagram: bit.ly/ThisOldHouseIG
bit.ly/AskTOHIG
Tumblr: bit.ly/ThisOldHouseTumblr
For more on This Old House and Ask This Old House, visit us at: bit.ly/ThisOldHouseWebsite
How to Set Up a Garage Workshop | Ask This Old House
/ thisoldhouse

Пікірлер: 1 700

@guyhandsome43 3 жыл бұрын

"Here's a free $1100 compound miter saw and stand" "NEAT"

@robdre1977 3 жыл бұрын

And heres 600 bucks of tools. "NICE"

@ernestlee5507 3 жыл бұрын

HAHA! I was thinking about all that the entire time.

@jbestell 3 жыл бұрын

Bitterrrrr lol

@hargharg 3 жыл бұрын

LOL She's happy, you can see it on her face. If the producer wanted her to gush, she would have.

@themomorain 2 жыл бұрын

Honestly I thought the same but at the same time Idk if my reaction would be that different. When I get a gift or something im also truly happy but I will not scream around or anything^^

@jeffmclowry 7 жыл бұрын

Sure wish someone would show up at my house and bring me tools.

@weaksrt4 6 жыл бұрын

Well then you should build a $12 dollar TV stand and they will come knocking on your door.

@daveoverbey2032 6 жыл бұрын

It might be alright if she knew what she thinks she does. L.O.L Was it me or did she seem a little unappreciative & totally detached during this show! It seemed she was only focused on something else other than the real deal she was receiving! I'd of been ecstatic getting all this for nothing & she seemed nonchalant about it. She sure didn't deserve it. She must think she's a queen or a princess & neither is she either. L.O.L

@daveoverbey2032 6 жыл бұрын

That's funny & your so right on it! L.O.L To me that stand looks like one I saw at the Goodwill store only it's been cleaned up a little bit.

@alonzomartii 5 жыл бұрын

And don't forget to wear sandals and paint your toenails.

@lapisredux 5 жыл бұрын

i wish stephanie was in my garage.

@solmanJapan 2 жыл бұрын

That mitre saw is pretty impressive. It moved itself out of the way!

@TheRogermursick 4 жыл бұрын

Tom's approach to doing things is straight forward, smart, creative and a pleasure to watch, always.

@DoleshEdit 2 жыл бұрын

I like how they did not 'over complicate' the fan system. Great shop set up!

@SoupLegion 2 жыл бұрын

could've used more duct tape

@glibbis 7 жыл бұрын

Tommy Silva is so awesome he can move things by telekinesis at 7:52!

@Malmioo 7 жыл бұрын

Mitcher Meandan I think the cameraman lifted it not Tommy

@glibbis 7 жыл бұрын

I don't know. I have been watching Mr. Silva for years and he has some pretty amazing skills. I wouldn't be surprised if he can move power tools with his mind.

@diyboomboxesintexas2805 7 жыл бұрын

Mitcher Meandan Good catch. I didn't see that the first time

@Googaliemoogalie 6 жыл бұрын

nah not telekinesis, he just commands tools to move when he wants to, that's his secret

@Wes8761 6 жыл бұрын

Holy shit good eye

@dmorga1 3 жыл бұрын

"HOW OFTEN DOES THE TRAIN GO BY?" "So often, you won't even notice it."

@jimtalbott9535 3 жыл бұрын

"You get mah cheese wiz boy??"

@shatoyancy9102 3 жыл бұрын

I liked the Wrigley Field bit. Yeah, real cute.

@Samuel-I 3 жыл бұрын

You do get used to it.... unless it shakes the entire house. When I was a kid we lived REALLY close to a set of multiple freight tracks. After about a week you didn't wake up or pay attention to them.

@farukatasever2933 7 жыл бұрын

Always a pleasure to learn something new from Great Construction Master TOM SILVA.

@vinced.7713 7 жыл бұрын

Original NES console was the best part.

@leloodallasmultipass 7 жыл бұрын

or, the worst part.

@ghosthead2008 7 жыл бұрын

Nope. The best part.:)

@jorymil 7 жыл бұрын

Definitely the best part. A woman who's into tools and NES... a guy can dream, right?

@SwankeyMonkey 7 жыл бұрын

I thought she was my trifecta dream: An attractive redhead who's also a gamer, and is into woodworking. Although, I'm more of a SEGA guy. These are my custom SEGA arcade cabinets: /watch?v=sBCYo9Kn1B0

@troymeredith521 6 жыл бұрын

They staged the entertainment center to have an original NES with games no less...not sure if Kudos to the planners or to tell the producers that they out a little out of date. lol. Great setup regardless, IMO.

@benchtopwoodworks 7 жыл бұрын

I liked the gate latch on the fold away bench, great tips for a small shop! I also reccomend locating tools around a central assembly table with parallel runs.

@austinmarius850 5 жыл бұрын

I think it’s great that it was sponsored by anyone at all. Especially Bosch. Lots of comments about that - Who gives a damn. Love that she is wanting to get into wood working and hope this episode helps other women get into this awesome hobby! That’s the only important thing here in my opinion is that smart, capable people are wanting to do things with their hands and imagination! What else can you ask for.

@elliottpeabody1287 8 ай бұрын

A winning lottery ticket.

@3nertia 7 ай бұрын

The problem is that many of us also wish we were provided such opportunities for free ...

@roderickfemm8799 5 ай бұрын

@@3nertia Why is that a problem? I've never understood the point of view that I should complain about someone else's good fortune because I didn't receive it too. Obviously they can't do that for everyone, and good for her for being the one.

@3nertia 5 ай бұрын

@@roderickfemm8799 The problem is that you don't understand the problem - it's a problem when *everyone* could live that way but instead we have over 2000 billionaires hoarding more wealth than any reasonable person could spend in 10 lifetimes ... *smh*

@roderickfemm8799 5 ай бұрын

@@3nertia [s] That's a powerful connection, between a video about how to fit out a garage workshop, to a political point about wealth inequality. I'm sure envy didn't play any part in your point of view either. [/s]

@muziclover-zr3gx Жыл бұрын

My respects to Tom and all his knowledge. I admire and respect, people like, Tom, for their love and dedication to their craft. Awesome job, Tom!

@bobbymiller5297 6 жыл бұрын

I like how Bosch sponsored this and made him put black tape over the Makita drill name in beginning because Bosch didn't wanna give her a hammer drill

@RoxStar1968 5 жыл бұрын

Or a table saw. Had to use the DeWalt

@twes619 5 жыл бұрын

Lol I know right. Like we don't know the colors of the most popular tools.

@dziadek1287 5 жыл бұрын

@@RoxStar1968 I think that the DeWalt is what she already had

@MrMOCENT 5 жыл бұрын

@@dziadek1287 looked super new

@Luckingsworth 5 жыл бұрын

@@MrMOCENT Yeah. Because she likely never uses it emphasis on the she

@vincentdwen 5 жыл бұрын

Well, first thing is you need to have an empty garage the most difficult part

@GregK9 2 жыл бұрын

Indeed!

@sterling6860 3 жыл бұрын

Nice to see Tom Silva again ,,Reminds me of getting up early living in Canada to watch all his shows,,learnt a lot about woodwork,,helped me to finnish off my basement ,,Happy days,,20 years now living in Perth W ,Australia and no basement ,But alas a 25 by 25 ft workshop to make bush bashing 4x4,s for my boys.

@chuzzrocket 2 жыл бұрын

Silva is the best. A mountain of practical knowledge and wisdom.

@DarkHorseWoodworking 7 жыл бұрын

I love my little woodworking shop too! Getting organized was the tough part.

@alwayslearning3671 7 жыл бұрын

Nice start for her. I might do one of those fold-up tables in my next shop.

@dtwilliams1779 4 жыл бұрын

Even though I'm looking for suggestions on how to organize my everlast welder tables I still found this video useful. Thank you.

@nordeenabdellah9371 4 жыл бұрын

What an enviable woodworking shop. Beautiful.

@mck7776 7 жыл бұрын

This guy is awesome! Greetings from Poland ;)

@chicagowsox212 7 жыл бұрын

So jealous that Tom Silva was within a few miles of me and I didn't know it! That dude is seriously an artist

@AFMomXs2 3 жыл бұрын

Just saw this video I really learned a lot. I plan on implementing the fan in my basement window for my craft room. Fumes from paint and stain and clear coat really linger in the air, even with a air cleaner.

@edwinvasquezp 5 жыл бұрын

Bosh auspicious this lady, congrats to her. Living under the bridge on the Lake Ave in Chicago I can’t imagine the train noise. Pretty cool the whole work shop, amazing job, I like the old house videos, I learn so much... thank you guys I’ll see y’all around Chicago 👍🏼

@artiet5982 6 жыл бұрын

Great episode! More like this with Tom. Also, this could've been twice as long!

@FrankOlsonTwins 4 жыл бұрын

That Fan rig is brilliant! 06:38 But I wonder how many times they had to wait for the train to go by to shoot the dialog scenes!

@priayief 6 жыл бұрын

Great video with some cool ideas. One of the best things I've done in my small shop was to build a cabinet base for both my table saw and my chop saw (the chop saw has folding arms). The cabinets make use of the area below the saw for lots of storage. Cheers.

@Delekham 3 жыл бұрын

She was the STAR of this video! I need to teach my wife these simple things.

@cesargonzalez5624 3 жыл бұрын

Bosch tools are rock solid. I am impressed with their 12 volt line. It's been my go to over their 18 volt drills. Most of the time thats all you need. I have the axial glide miter saw 12 inch. According to the specs it weighs about 88lbs add another 60lbs for the stand and its really freaking heavy. I mounted it on the cheaper Bosch stand and it tipped over and smashed my arm and leg. Huge bruises. Best miter saw but don't get a weak stand. I also have a bunch more tools by Bosch. You can't break them. They are insane.

@butseriouslythough3931 4 жыл бұрын

Thank you for this video. Regardless of all the obvious sponsorship, it gives a newbie a lot of great ideas on how to start a shop in their garage and I’m talking all the help I can get.

@mjd3879 3 жыл бұрын

Honestly, even though its all Bosch, at least he didnt mention the brand name, i really like these videos because he merely describes what the tool does, not what makes Bosch better or anything. I don't consider this selling out it was tasteful.

@PegasusFleets Жыл бұрын

Ohhh man .. Chicago.. always loving Chicago !!

@hoomalimali6334 3 жыл бұрын

The whole world loves you, Tommy!

@gatewaysolo104 7 жыл бұрын

Gee I wonder if bosch sponsored this episode

@DarkRaptor99 7 жыл бұрын

It used to be all Dewalt and Festool on This Old House and Ask This Old house for the most part I wonder if the sponsorship for the show changed. Bosch makes nice tools but their Cordless tool lineup is small compared to Dewalt Makita or Milwaukee.

@MaDeuce80 7 жыл бұрын

Gee I wonder if pine or poplar sponsored the video!

@bigvegass 7 жыл бұрын

Gee I wonder if the El sponsored the video.

@GREATGARLOOXX 7 жыл бұрын

Wes the big question is who sponsored the sponsors

@XzTS-Roostro 7 жыл бұрын

The Home Depot has been the underwriters of the show since it's creation at Boston's PBS station, WGBH-TV.

@mrjodoe 7 жыл бұрын

lol very impressive safety sandals. The yolo style

@wendysbrian1 5 жыл бұрын

Lol @ "Safety Sandals". Your alliteration makes it sound like a real thing when it's not. So funny. :)

@Wild-Dad 4 жыл бұрын

Can't you see the transparent aluminum toe covers for the sandals. If it's ok to use to transport whales, it should stand dropping a hammer on it. Actually, in all seriousness, there are "saftey shoe" sandals available to purchase. They are rated only to protect the bottom of your foot. You can't wear them anywhere your toes can get injured (which to mind mind is everywhere).

@carlfritz9496 4 жыл бұрын

I had an neighbor from India who would wear sandals while mowing his lawn. My family always laughed about how he was wearing his safety sandals.

@buddyclem7328 4 жыл бұрын

@@carlfritz9496 I know a guy who did that in wet grass, on a steep incline, with a mower without a safety stop! He lost both of his big toes, and now he walks with a waddle.

@carlfritz9496 4 жыл бұрын

@@buddyclem7328 I'm not at all surprised. Even though we chuckled a little bit about our neighbor, at the same time, it made me cringe to watch him mow the grass. There was a kid at my school who cut off the front 1/4 or 1/3 of his foot with a push lawn mower when he was a small boy. He still managed to be a pretty good athlete even with that disability.

@jpulley 5 жыл бұрын

That fold away space saving table is a great ideal. I will be doing that myself.

@passivesolarhousingcoop1903 3 жыл бұрын

Tom is absolutely amazing!

@alishanmao 4 жыл бұрын

This video solved my issue. I am thinking to get into woodworking as I like to craft build and make. and I was wondering how i can turn my garage into a wood working workshop. I still may need proper ventilation and dust collection stuff.

@juanvaldez7613 3 жыл бұрын

If you do dust collection, look into using pvc pipe. It is light and cheap. As long as you don’t mind looking at it, it is easy to get wall mounting hangers that will hold in place as well. It wouldn’t take too much effort to get a network system around a garage/work shop. Shop vacs are a good simple option as well as you can get hose attachments for many hand held power tools slouch as routers or sanders. May not be as effective for larger tools such as table saws or radial arm saws.

@bobbg9041 3 жыл бұрын

@@juanvaldez7613 pvc pipe is not Code. code states metal pipe, because of static electricity and saw dust is dry and really flammable materials. the 2 do not mix. With that said you can look online for fires caused by plastic dust collection pipes I doubt you find any. But there is always a risk of static charge and ignition of saw dust. You will find Dryer fires from lint I've had a dryer burst into flames from lint and it was an electric dryer. Lint is very very flammable great to start a campfire with. Servlists use it for that. you have to weigh the pros and cons and know what your getting into. The shop vac works on a RAS and portable table saw not good on large cabinet saw worthless on jointer worthless on planer pointless on lathe Works great on my router table the router is in a box. Add a dust deputy its not as good anymore and the filter clog fast. Also good on a hand sander. If your going to use metal pipe don't bother with standard duct work its too thin, you want spiral pipe. I'll be running a 2hp 240 volt machine with a Hepa filter I plan on converting it to a 2 stage unit with a separator and 6" pipe. Study this stuff before you buy anything or you will waste money really fast that you can use on other tools. If your in a detached garage without heat you can just blow the dust out the window, no big deal if your in your home like a basement you going to want dust collection or you will clog your furnace filters and coat everything in your house with saw dust. A garage differnt story it depends. Is it heated?

@robertf6344 3 жыл бұрын

yea, after a few projects I can only imagine the amount of sawdust all over everything in there.

@johndeneen980 2 жыл бұрын

Did you get it done and how did it turn out?

@DRJGD666 7 жыл бұрын

I'm a fan of the window fan thing.

7 жыл бұрын

DRJGD666 me too... but my window will go directly in my house from the garage ^^

@frameriteairdrie578 6 жыл бұрын

I'm a thing of the window fan.

@pyotyrprepka1875 3 жыл бұрын

Folding bench is a great idea. I have a small one car garage too and barely enough room to get out of the car unless I park close to the right side. No window though. That bench will make it easier to do home repair projects. Peg board up high good idea too so tools can be easy to reach and still get car inside. Cold snowy winters here too.

@daviddoyle4516 4 жыл бұрын

Tom Silve is the 8th wonder of the world ,,,I been following his videos and articles forever and always learn something. DD

@tonys623 3 жыл бұрын

"You might wanna pawk a caw in here in the winter time"

@wisconsinwoodsman1987 3 жыл бұрын

Sawr and chisel.

@VideoNOLA 6 жыл бұрын

7:50 Silva's invisible Jedi Mind Lift in action!

@DanTheManIOM 3 жыл бұрын

I could watch Tom work all day ! Yea, I watched this twice, so what ? I like it.

@williamfotiou7577 Жыл бұрын

Yeah, great video. Really made me think about wood, screws and double entendres!

@Artheon 7 жыл бұрын

Finally, TOH is catering to the small-shop DIY movement.

@forestflare6816 7 жыл бұрын

The wrenches might have been my favorite part.

@prorican48127 2 жыл бұрын

This is still one of my favorite TOH videos

@fessit 3 жыл бұрын

Tom Silva you rock! Great video!

@RicardoJunqueira 7 жыл бұрын

Great episode, cool ideas.

@ttjordan81 3 жыл бұрын

Lady: "I actually built this piece myself", Tom: "you did!", then inspects the furniture piece corners for rough edges and joint tightness...classic, Tom is such a professor! lol

@mynameisfake8200 3 жыл бұрын

i noticed same thing

@Dudeinator 2 жыл бұрын

yeah thats the things i look at first lol

@judoyodan 4 жыл бұрын

I have the same mitre saw and stand. Love it.

@al52269 4 жыл бұрын

Great small shop ideas. Thanks for sharing

@KewlCrayon 6 жыл бұрын

I liked the idea for the folding wall table, def gonna do that for my place but I want to make it stronger and finish it off alot nicer too. I really want to glue laminate myself a big solid table but my garage is not much bigger than this garage. As for the ventilation system, oh god no, that one fan in the window is not nearly enough, should set up a large shop vac in the corner of the room and route a hose overhead to your saws. Also that foam on the floor... the floor was easy to sweet until you get that form there, now you gotta vacuum it. Much better just having solid concrete flat floors with no mats or anything that will create edges for dust to collect on.

@RetroGamingOnline 7 жыл бұрын

Gotta love the NES with some great games!!

@erichondel6221 7 жыл бұрын

Retro Gaming Online Do you know which games she has?

@shamibeef 7 жыл бұрын

You're a good man Tom!

@donmotz5528 7 жыл бұрын

I like that arm system on that mitre saw....makes it so nice to be closer to ur wall...

@TheMinishKid 5 жыл бұрын

The combination of a strawberry blonde and a classic NES makes me so happy for some reason

@thewickedestone 4 жыл бұрын

"Hey, I see that you built this nice entertainment center. Let me explain to you how countersinking works."

@kountryedge 4 жыл бұрын

It was an explanation for the viewers. Don't be rude.

@walterbrunswick 3 жыл бұрын

No kidding, that cabinet was lit

@sharkysmachine9248 3 жыл бұрын

Wonderful sounds of the elevated trains passing by, reminds me of the scene in Blues Brothers movie. Too funny

@fabianmahorn7545 3 жыл бұрын

I like how when he starts drilling pilot holes, the closed captions say, [Applause] [Music] Aw yes indeed, it is music to my ears.

@JanitorIsBack 7 жыл бұрын

7:51 where do I get the that saw stand that lifts up by itself?

@uglyashelful 7 жыл бұрын

JanitorIsBack I'm pretty sure menards has it. Any big box store that carries bosch tools should be able to order it for you. In my opinion, the lighter foldable horse style stands are much better. They are about half the price too.

@MrGrimm1911 7 жыл бұрын

I just figured Tom lifted it up with the power of his mind.

@uglyashelful 7 жыл бұрын

MrGrimm1911 Nope, gas springs.

@krn14242 7 жыл бұрын

Jedi Mind trick.

7 жыл бұрын

JanitorIsBack www.magic-Bosch.com ;)

@Blobjonblob 7 жыл бұрын

Pretty cool work space, Dont know how long them concrete screws will hold into those red bricks a sleeve anchor would be better suited

@dougerrohmer 7 жыл бұрын

I wondered about that! North Americans have totally different buildings, so I thought that's the way it goes and they have special bricks or something :-)

@Blobjonblob 7 жыл бұрын

Douger Rohmer you can just about see that one of the screws Tommy puts in spins freely.

@dougerrohmer 7 жыл бұрын

So things aren't all that different :-)

@Blobjonblob 7 жыл бұрын

They defiantly have a place but a sleeved anchor are vastly superior

@strandloper 7 жыл бұрын

I was wondering about that. Most DIY/woodworking videos from the US make me jealous of the ease with which they mount things on their framed walls. Here in South Africa, walls are generally brick and we would always used a sleeve anchor, or rawl plugs as we call them when putting screws into them. I did notice though that the screws they used were probably twice as long as we would use with rawl plugs.

@scottpecorino6320 4 жыл бұрын

Love the folding table.

@macattack949 4 жыл бұрын

I love these videos. The first hole was blown out and the screw didn't grab anything as a result.

@ipasuhd 7 жыл бұрын

A train direct in front of a house? AWESOME! Sure can be quite loud, but A TRAIN!!!! WHOAAA

@crazyhass84 5 жыл бұрын

Train is better than the shores and drugs dealers down the street. Its shitcago!

@EricInTampaAcoustic 7 жыл бұрын

Tom is a great guy

@SteveP-vm1uc 5 жыл бұрын

I sure wish I could get these guys to come to Florida and do a bunch of work around our place!! I use to be able, but,,, " This Old Back " keeps me from doing everything I need to get done.

@BigLazyMexican 7 жыл бұрын

awesome video great ideas and ways of thinking for things that I would miss since I don't wood work often except for outside

@donovanwisdom310 7 жыл бұрын

If you have 20 minutes and need a laugh read ALL of the comments below. Bravo people.

@xxbondsxx 3 жыл бұрын

yes this comment thread is amazing, even 3 years ago

@miamitreasurehunter 7 жыл бұрын

Don't be haters. I wish I had a shop like this. She is one lucky lady (Minus the L Train 😀)

@daveoverbey2032 6 жыл бұрын

The truth be known, Is that this workshop is for her boyfriend to do all her honey doos. L.O.L & this show paid for it all & got little thanks for it. She might think or try to convince herself she deserves it on an account she claims building that goofy table makes her a real craftsman. L.O.L To deserve all this & not show any real appreciation is her slapping the show in the face.. If they want to give away nice tools like they gave her they can look me up & or least give them to habitat for humanity & or hammers of hope as at least they will go to good use & not.be a wasted. She looked like a real journeyman to me! L.O.L

@justinballew60 6 жыл бұрын

Same here. I'm looking for ideas for my garage shop at the moment.

@NarwahlGaming 6 жыл бұрын

Jimeny Christmas, Dave... Is this lady your ex, or something?

@scottie_2024 5 жыл бұрын

He's probably just a misogynist.

@wendysbrian1 5 жыл бұрын

@@daveoverbey2032 "try to convince herself she deserves it on an account she claims building that goofy table makes her a real craftsman." Jesus Christ, the savagery, lol!

@carolmaplesden916 Жыл бұрын

i think its Tom i remember watching on PBS around 1975ish He was doing wood working in his garage and i remember how all his tools saws and stuff seemed so complicated and expensive I really loved his work i wanted to learn how to do it but it was all way over my head

@tighecrovetti2844 3 жыл бұрын

Having Tom Silva set up your small shop….so jealous!!!

@Viralclown 7 жыл бұрын

Anyone notice her screws into the brick slipped?

@2HME 7 жыл бұрын

yep that stood out to me more than anything else...

@still34u 7 жыл бұрын

Did you notice, she changed her "technique" after the first one?

@gordbaker896 7 жыл бұрын

He drilled into mortar instead of brick

@still34u 7 жыл бұрын

I noticed that too, but I figured it shouldn't be that big of a deal

@warrenbuitendag5286 7 жыл бұрын

yeah me too, you would think they would edit something like that out of scripted stuff like this.

@Danim24 7 жыл бұрын

I wonder if Bosch noticed he used a Makita drill at the beginning?

@bobbymiller5297 6 жыл бұрын

with the tape over the name

@raabsand 6 жыл бұрын

Well those Bosch he gave her wouldn't do what the makita did

@TheAavelar007 4 жыл бұрын

It was Hitachi

@daniel1980ization 6 жыл бұрын

drilling through that 2x4 with your masonry bit is a wonderful idea! look at all that smoke coming out, it indicates your drill bit is cool and working properly i bet...

@kansasindependent4015 6 жыл бұрын

I have to say this chick is awesome way to go Tom Silva great video very nice of you to help set up her new work shop good job : - )

@Basard100 7 жыл бұрын

The first anchor failed. You can see that they took it out--the first hole is empty all of the sudden. I saw that he drilled easily into the mortar, and I saw the anchor fail right away--the screw kept spinning (ex-roofer here.) "This Old House" should explain these things. It would help a lot of people from failing at first.

@bsnoonan 6 жыл бұрын

Do you seriously need them to explain if your first one fails, just drill another one?

@shawniscoolerthanyou 2 жыл бұрын

I saw that too. It would be nice if they broke the illusion that everything works perfectly the first time.

@laissezfaire9762 2 жыл бұрын

My first question was "What's the drill bit?" It doesn't look like a regular masonry bit. I also wondered if he was drilling into the brick or the mortar? And, what about using lead wall anchors?? Will those screws loosen over time? And then there's the cost of tools, especially the mitre saw. I think the concepts were fine but like Basard100, I think this video was a bit glossy.

@greenhornadventure 7 жыл бұрын

If she is competent to use a table saw, router, and mitre saw, does she really need to be shown how to build a workbench?

7 жыл бұрын

Greenhorn Adventures She don't know... the tablesaw is never touched before!!... even the other tools is just mount on a peace of plywood and put in the garage...

@plowmaster1206 7 жыл бұрын

Scruffy yabut it's t.v. Sexy

@NSMike87 7 жыл бұрын

It's a demonstration for a TV show - the workbench build wasn't for her sake, it was for the viewers'.

@stevoc9930 6 жыл бұрын

Because mansplaining

@34stzoo 5 жыл бұрын

She knows how to use a table saw, router, miter saw. She's acting like a novice because she's having her shop built and new tools for free (that's why there are no scruff marks. I would behave the same way.

@jiujitsuboxer 3 жыл бұрын

I’m doing the fan tomorrow. That’s awesome.

@joeseabert8391 4 жыл бұрын

That fold down table is a great idea.

@ottomau5 4 жыл бұрын

I’m in love with this chick.

@TaeFace93 7 жыл бұрын

Nice! Perfect! Okay!

@dtrrtd774 7 жыл бұрын

Did seem quite chirpy-

@patrickwhitehead7584 5 жыл бұрын

Thats a really clever way to use a box fan. I'll be doing that.

@jewdd1989 6 жыл бұрын

Love this thank you and love the pocket holes ;)

@crmcbrideww 7 жыл бұрын

No need for dust collection, she has a box fan!

@erix 6 жыл бұрын

I thought he was going to hook her up with a dust collection system, then he comes out with a box fan he drilled a couple holes in.

@bighands69 5 жыл бұрын

I am sure she can get a portable dust collection system for her tools.

@thenitpicker911 5 жыл бұрын

erix your theory about he hooks her up made me laugh so hard :)))

@kennethpaquin8574 5 жыл бұрын

And it is hard to get ventilation from one window on the end of a long room. She'll need to at lease crack the garage door if she wants to push out fumes.

@243wayne1 4 жыл бұрын

No. She has a box. AND a fan. Class dismissed.

@Achilliez 4 жыл бұрын

The old boy loves having the drill on hammer drill to drill through the wood.

@woodworking4971 5 жыл бұрын

nice cozy place small but very practical, that's all I dream!

@lindabrown7374 7 жыл бұрын

Really like the hanging fan.

@bentyreman5769 7 жыл бұрын

where are the hand tools?

@gregoryvangundy6170 7 жыл бұрын

Lots of good advice. One criticism is that a miter saw has limited utility in a small shop where space is at a premium. A bandsaw would offer a wider range of possibilities. With a sled long boards can be broken down safely on a table saw or ( gasp) a good handsaw. Very cheap and sharp pull saws are readily available.

@fakecubed 6 жыл бұрын

That miter saw is totally overkill for anything she would possibly be doing as a wannabe woodworker, but Bosch is paying for the product placement so maybe she'll just sell it on Craigslist. I agree a band saw would be a lot more useful, and they should've given her a planer and jointer.

@supremelawfirm 6 жыл бұрын

Tom et al., you are THE BEST west of Paris, France!

@jaymartinez711 11 ай бұрын

I love how this feels like PBS special.

@bshilkitus 7 жыл бұрын

That first screw didn't grab.

@VideoNOLA 6 жыл бұрын

Saw it spin, too. Silly not to use appropriate anchors in the brick wall!

@JT-91 5 жыл бұрын

@@VideoNOLA That table is going to fall the first time it's load bearing.

@Thatmemphiskid 5 жыл бұрын

Looks like he missed the brick lol

@stoicllc2352 3 жыл бұрын

Virgin

@highplains7777 3 жыл бұрын

That's what she said.

@FredmChoice 3 жыл бұрын

Im hooked on his segments 🤩🇦🇺🤩

@javierchavez3610 7 жыл бұрын

TOM YOU ARE ALLWAY THE BEST OF THE BEST

@necrojoe 7 жыл бұрын

Someone "interested in getting into woodworking" now has a $600 miter saw, while I actually work and I have a $199 saw. Nothing against her really I'm just jelly and bitter. That exhaust fan is janky, though...and also pocket hole joints aren't "super stong". Perfectly adequate for many things, but would never call it "super strong".

@algalkin 7 жыл бұрын

I'd say, better would be money spent on 199 miter saw and another $400 on a planer.

@cup_and_cone 7 жыл бұрын

necrojoe - Pockets joints really just hold it together while the glue dries, but provide the instant strength to continue without needing to worry about the glue drying like a biscuit joint.

@dandragland825 7 жыл бұрын

necrojoe - Same goes for that router setup. Not that a router's in the 600 range, but still.

@joecleveland6525 7 жыл бұрын

On an end grain to long grain joint like they showed glue will add very little strength. With that fancy plunge router they could have made a mortise and tenon joint, but this show is really about selling tools more than good technique anyway.

@Chris012345671 7 жыл бұрын

Not only a very expensive compound miter saw but a very large one in such a small space. it would be best to fab a miter sled for that table saw