How to put a 90 Degree Bend and a Double Set into one length of Steel Conduit!

Рет қаралды 68,468

Күн бұрын

A set by step walkthrough of the process to produce a 90 degree bend and a double set in one length of steel conduit to given dimensions.
======================
🕐 TIME STAMPS 🕕
======================
00:00 90 degree bend and a double set in steel conduit
00:49 Depth of the set
01:08 Remove the depth of the saddle
01:31 Coupler on firm
01:53 First bend 100 mm from the end
02:15 Start of the first bend
02:45 Find 70 mm
03:10 Mark the conduit
03:35 Mark against the former
03:58 Parallel
04:48 Fine adjustments
05:40 Measurement from the socket to the back of the bend
06:10 Mark the conduit
06:40 Top tip
07:37 Position the back of bend make against the former
08:27 Bend to 90 degrees
09:01 More bend required
09:41 Is it too short?
10:10 Measure for the final cut
10:54 Measure for the final cut
11:38 Cutting and treading
12:36 Reaming
13:17 Will it fit
================================
🔦 More conduit videos from eFIXX
👉www.efixx.co.uk/metal-conduit
👉www.efixx.co.uk/how-to-bend-co...
👉www.efixx.co.uk/conduit-instal...
==AD=====================================
Series produced in association with
Metpro - Conduit and accessories
👉 hub.efixx.co.uk/metpro
Bend-it-now - Conduit Bender
👉 hub.efixx.co.uk/bend-it-now
=========================================
📍SUBSCRIBE TO THE CHANNEL eFIXX helps electricians, electrical contractors, building services engineers, and electrical apprentices. So if you've been on the tools for years or just starting your electrical journey, we'll help you stay up to date with the latest regulations and developments in the electrical industry. 👉hub.efixx.co.uk/youtube-subscribe
========================================
⚡️ Take a deep dive into the latest electrical products, applications and technology
👉 hub.efixx.co.uk/essentials
=========================================
🚧 More resources for electrical apprentices and learners
👉 hub.efixx.co.uk/apprentice
=========================================
#efixx #conduit #electrical

Пікірлер: 107

@Jackh1676 2 жыл бұрын

Absolutely bang on if you’re preparing for the AM2. Sat mine last week and passed first time. Cheers gents.

@efixx 2 жыл бұрын

So glad it was helpful 👍🏻 Gaz

@callumsimpson7483 2 жыл бұрын

Well done jack what advice would u give us mate got mine near mid summer if I do my nvq in time

@GSHElectrical 2 жыл бұрын

Great work 👍🏻

@luluboxingtv2880 2 жыл бұрын

Got mine on the 16th mate , any tips ??

@luluboxingtv2880 2 жыл бұрын

@@callumsimpson7483 you doing the experienced worker nvq? I had same issue I had to complete nvq before I could sit am2 but got my certificate last week thank god

@markandrews8437 2 жыл бұрын

That was excellent thanks, there's not enough videos on KZfaq on conduit bending for UK trainees this series you are doing is absolutely 100 percent perfect, I didn't know about deducting the 6mm for the saddle which explains a lot keep this stuff coming it's extremely helpful even to us know finally qualified guys 👍

@efixx 2 жыл бұрын

Thanks for the great comment Mark 👍🏻

@jameshansing5396 Жыл бұрын

SKILLS! Absolutely in awe!

@mathgeek1260 9 ай бұрын

Smashing video lads! Keep up the good work 👏

@Randrew998 2 жыл бұрын

Wish this video came in sooner but I passed my AM2S last week yay! The double set has to go into a central heating centre and must be central above the DB, the set I had to make was much lower than the one in this video but I’m sure all training centres are different slightly. Thanks for the video this will help a lot of students out there for sure !

@Lloydy0105 2 жыл бұрын

Not sure how it would fair in the AM2S, but for anyone else. A tip for the last cut. If you can get the distance from the end of the coupler. To the back end of your 90 bend, cut it at that + 15mm Thread it so the end of your conduit is level with the first line of the nut of your stock and dye set (see 12:43 in the video, he’s done it) that threads the conduit to exactly 15mm (30mm on the 2nd line) Every time, or atleast it has done every time for me since I’ve been using that method after I was shown it on site 4 years ago

@dgiomar 2 жыл бұрын

Absolutamente perfeito, um ótimo trabalho parabéns. Perfect joob.

@jonathanrose456 2 жыл бұрын

Good job. Magnetising the square makes it a bit easier

@rgbrownelectrics Ай бұрын

Top video chaps. Got this exact job to do on my AM2E tomorrow. Very helpful

@neil6438 2 жыл бұрын

Nice job.

@berkotropia 8 ай бұрын

Well done mate! I'm gonna teach this soon to students! It was very helpful video! I will give you credit!

@muhammedajmalvp420 2 жыл бұрын

This video very useful Thanks ☺️

@remoraju6773 Жыл бұрын

Wow it's perfect work 👏

@raythirkettle4155 2 жыл бұрын

Good craftsman...spot on!

@efixx 2 жыл бұрын

Thanks 👍🏻

@joanofarc708 Жыл бұрын

Very helpful thanks

@piotrlobacz Жыл бұрын

There are incliniometers available allowing to take guess work out of bending. Great channel and fantastic set of videos. Well done guys.

@mikethemask1525 2 жыл бұрын

Just found this channel but I must say its really good I'm a sparkie and even I'm seeing a few things that can help me so thanks guys great work

@efixx 2 жыл бұрын

Thanks Mike - hope to see you as a regular in the comments!

@jexigunn7821 2 жыл бұрын

i love you guys. very helpful.

@GSHElectrical 2 жыл бұрын

Thanks 👍🏻

@brianwood5220 2 жыл бұрын

Grand job Jake. Now i'd like to see you go down the pub and have yourself a pint. I think you've earned it 😁

@LucasMUFC8822 2 ай бұрын

Made it even easier by adding the through box in between bends!

@paul_my_plumbs_uk 2 жыл бұрын

More AM2 please 💪💪💪 start to finish and everything in between 👍👍 HNY 2022🍾🍾🍾🍾

@efixx 2 жыл бұрын

Thanks 👍🏻

@noskills9577 2 жыл бұрын

Hope to learn metal conduit this year, good video

@efixx 2 жыл бұрын

Thanks 👍🏻

@Dibbo1979 2 жыл бұрын

Cracking video 👌🏻

@efixx 2 жыл бұрын

Thanks 👍🏻

@shiamjad Жыл бұрын

Thanks a lot

@fahadmalik10 Жыл бұрын

Awsm video sr .

@neilcarter3365 9 ай бұрын

Bang on that was cheers.

@GalacticGazetteHQ 7 ай бұрын

Great video lads trying to get the apprentice through his am2 he knows everything obviousley and shit himself when i showed him your videos! youth of today!!

@highgatehandyman6479 2 жыл бұрын

Great conduit

@kingofthetrowel1725 2 жыл бұрын

Nice one fellas 👍👍

@efixx 2 жыл бұрын

Thanks 👍🏻

@jackninnu9719 Жыл бұрын

2 kings one throne🍾🎉

@Angel_of_the_Blade 2 жыл бұрын

I am very impressed by this excellent work ! But I would want to see how you get a wire in this tube ;)

@dezire8470 2 жыл бұрын

Can you show us a crank/bubble set in plastic conduit as this is also on the AM2s

@TheManLab7 Жыл бұрын

I've never had a bender in my LIFE that starts at the very edge of the former. It's always a little ways in and to make sure it's repeatable. You mark the ACTUAL start by cutting the edge of the former. I had a brand new bender one time so I cut a mark where it actually starts to bend too help everyone else out 🙂

@joeheyes1513 Жыл бұрын

I’ve got my AM2s in July just refreshing myself on steel comduit. I’ve seen differing information though about the AM2s and what you need to do for the steel conduit section. I’ve heard just a double set and 90 bend like in this video but also the above and a running coupler. Does anyone know if the running coupler is actually a requirement for the a AM2s steel conduit section. Thanks

@tangyo166 5 ай бұрын

Good

@pjcamp1on 2 жыл бұрын

what else is part of the AM2 ? do you still have MICC cable (pyro)?

@kentmasic 2 жыл бұрын

I passed metal conduit but failed plastic, on retake I had to retake both, felt okay about plastic but metal was so perfect and fit in like a dream! Flush either side but got the result back and I passed plastic and failed metal 😂 appealed it (knowing/them tell me getting a pass is almost impossible at that stage) but got the email to say that my appeal was successful! 🎉🎉🎉

@efixx 2 жыл бұрын

Great work 👍🏻

@colum9911 Жыл бұрын

🤔🤡

@M0PAX 2 жыл бұрын

Very nice video I would also file the jaw marks of the tube as well, nothing worse than sliding your hand over the tube and slicing hand.

@rondelwilliams2925 Жыл бұрын

can guys please do some tray fabrication PLEASE!

@TheLordporter Жыл бұрын

Could you link me the video where you guys mark the bender for sets?

@marcoequi446 Жыл бұрын

How come you didn,t use any locking rings or segerated washers on the conduit?

@alanmarriott9216 9 ай бұрын

Can I ask please. If you put conduit into former from opposite end how much does it add or subtract from measurement. Hope this makes sense! (Normally you put measured end into former from front first)

@dezire8470 2 жыл бұрын

Would you not do the 90 first so you can hold it on the wall?

@darkdepth1991 2 жыл бұрын

First time right ! What a beautifull video eFIXX ! Possible to make a video with PVC conduct and a bending spring ?

@efixx 2 жыл бұрын

Thanks for watching 👍🏻

@markkennard861 2 жыл бұрын

Go buy one and start bending ! Here in NZ the 90deg bends are cheap as chips so I no longer use a spring. Also here there is very little metal conduit along with metal flush boxes. Measure twice cut once is the key.

@darkdepth1991 2 жыл бұрын

@@markkennard861 I am from the Netherlands 😎 We use different installation systems here like the "central box system" (You go from your circuit breaker to a central box ( lighting point ) and from there to your switches and sockets or next central box. The circuit type is called radial in the UK). For Cables and wires we use plastic conduct and we use a spring to bend our conduct, use fixed bends or flexible conduct But eFIXX has so many good technical videos. It doesn't matter where you from, they will always share something that can be used in any type of installation.

@londonviewer3483 2 жыл бұрын

Those bending machines need some sort of angle markers built in

@andyclark1426 2 жыл бұрын

Absolutely beautiful!!! I don’t do much conduit, but practicing at work when team leader not about 😉, 1 question though do you not require a lock ring at rear of coupler or is it not required as the coupler is “locked up against male thread and brass bush”??????

@eggster71 Жыл бұрын

More of a Scottish thing I believe.

@colum9911 Жыл бұрын

A lock ring? Why when the coupling is tight

@thetruth6693 2 жыл бұрын

How did you know the degree to do your first bend mate?

@eddie_pegasus_electrical Жыл бұрын

As always a great tutorial on UK conduit skills. Well done guys. Though I would use a 1/2” (13mm) brush for the cutting paste, less messy and wasteful when hand threading. Also a reamer and magnetic welders square, though these probably wouldn’t be available on an assessment for AM2. Just a thought 👊😎👍💙

@Zombie_Longwinger 2 жыл бұрын

How many goes did you do ? I’d have hidden all that bent conduit in the corner of the video first 😜

@efixx 2 жыл бұрын

Scrap man is always hanging around when these are being filmed

@elsdonsparks 2 жыл бұрын

@@Zombie_Longwinger We always had "The Conduit Graveyard" in the corner

@spartan90909 2 жыл бұрын

@@Zombie_Longwinger bit of paint stripper or wet and dry always sorted the print out

@polski1014 2 жыл бұрын

Myguy stood there like a body guard

@tonupturner 2 жыл бұрын

Is this the same across all colleges? We were told we have to do a bubble set in galv conduit.

@efixx 2 жыл бұрын

The bubble set for AM2S is in PVC conduit 👍🏻

@alanmarriott9216 2 күн бұрын

Great video but can I ask how on site are you suppose to score a line for bend when don’t have a workbench to use!?

@gadgetman36 2 жыл бұрын

Wouldn’t a reamer be a more efficient way to remove the burr than a round file after cutting?

@jimbob1ist 2 жыл бұрын

I was taught to use a closed pair of side cutters

@dan0491 2 жыл бұрын

Is this the exact layout of the bend we will need to do?

@efixx 2 жыл бұрын

It’s an example 👍🏻 - it will have a bend and a set

@brianmac001 2 жыл бұрын

Been a while since I was in the trade but does no one use lockrings anymore?

@robertwilliamson3934 2 жыл бұрын

Exactly still in the trade and frequently do conduit I always use lockrings so I can tighten things up In all my years I have never put two lengths of pipe together solely with a coupling and it been straight always two rings and a coupling so you can adjust and tighten

@anotherledfreak8649 2 жыл бұрын

Lock rings and running threads get you out of trouble so easily. Yet a lot of the newer guys just don't use them...

@grumpygit447 2 жыл бұрын

You go on building site and they supply you with nice new bender and workbench to work with 🤔🤔

@anotherledfreak8649 2 жыл бұрын

Hated my AM2 over 30yrs ago but still passed. Seem to remember having a pyro (mineral insulated) cable to do too (but I might be mistaken). Nice to see some things don't change... Its still a BITCH! 🤣🤣

@davewalters6214 2 жыл бұрын

my work always looks good.but i think me,you,and the builder are the only ones who can tell if its a little off

@Caniksigboy78 11 ай бұрын

What kind a bender is that?

@oliverheath7285 2 жыл бұрын

I ended up having to borrow someone else's. don't use it much in my company. Did the plastic one fine but failed massively at this 🤣

@John-gv1fl Ай бұрын

Why wasn’t it bent at 45 degrees as in other videos it is?

@AlexBregu-nw8fb Ай бұрын

Does anyone the formula for in example I have 1000mm left scrap (left over pipe ) 20mm steel conduit and I want after my bend to be 200mm I know I can mark 55mm in top of my bender and I get 100% correct . What I don’t a understand from 1000mm how much pipe it’s going to be left as I have tried training something I am losing 110mm sometimes 150mm sometimes 50mm I don’t know why .😅😅😅 just learning .

@kyester123 2 жыл бұрын

That was tasty at the end. Spot on

@efixx 2 жыл бұрын

Thanks 👍🏻

@dvrn86 7 ай бұрын

I hate bending when the conduit sits in the bender at too high of an angle. Why can't they make benders where the conduit sits in the bender at level 0°