How to Re-Cloth Your Pool Table Rails - FULL DIY GUIDE, BEST ON YOUTUBE!!!

Рет қаралды 210,587

Күн бұрын

Need to replace the cloth on you Pool Table Rails? Then check out this in-depth DIY guide packed with tricks and tips, do it yourself and SAVE MONEY!
AMAZON LINKS:
Air Stapler:
Amazon USA: amzn.to/47o9VFX
Amazon Canada: amzn.to/46r3SiP
Amazon UK: amzn.to/3RcNdeg
T50 Staples:
Amazon USA: amzn.to/40MVbyd
Amazon Canada: amzn.to/49PFiew
Amazon UK: amzn.to/47Kmb3r
Staple Remover
Amazon USA: amzn.to/3SYKmY1
Amazon Canada: amzn.to/3QS0RCl
Amazon UK: amzn.to/46s3EI0
Worsted Cloth:
USA: amzn.to/3e2eX1q
Canada: amzn.to/3jl53L2
UK: amzn.to/3Iq2HYw
Napped Cloth:
USA: amzn.to/3NGG5Vt
Canada: amzn.to/3VMymX9
UK: amzn.to/3CqFRfG
CHAPTERS:
0:00 Intro
0:23 Preparation
1:00 Removing the old cloth
4:48 Feather Strips
5:23 Feather-Stripping the new cloth
7:50 Trimming up the cloth on the feather strip
10:45 Preparing for stapling
11:53 Working the corners
14:55 Finishing the rail straights
16:56 Finishing the ends
18:03 Trimming the cloth
20:21 Side pockets
22:33 The fold
25:35 Feather Strip Tips
32:44 Final Thoughts
OUR OTHER POOL TABLE CONSTRUCTION VIDEO'S:
Pool Table Complete Installation:
Basic Install, Older Table: • How to Install and Clo...
Advanced Install, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Level Your Pool Table Frame:
Basic Method, Carpenter Levels Only: • Pool Table Assembly: H...
Advanced Method, Machinist Level, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Level Your Pool Table Slates:
Basic Method, Carpenter Levels Only: • Pool Table Assembly: H...
Advanced Method, Machinist Level, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Seal Your Pool Table Slate Seams:
Beeswax Method: • How to Seal Pool Table...
Bondo Method: • How to Seal Pool Table...
Sealing Pool Table Slates: Beeswax vs Bondo - Which is Best?:
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Make Pool Table Slate Pocket Liners:
Advanced Method, Neoprene or rubber etc: • How to Make and Fit Po...
Basic Method, Cloth Strip: • Pool Table Cloth Insta...
How to Replace Your Pool Table Cushions:
• How to Change Pool Tab...
How to Fit Your Pool Table Cloth:
Advanced Method for Worsted Cloths inc Simonis/Predator/Championship etc: • Pool Table Cloth Repla...
Basic Method: • How to Install a Pool ...
How to Calculate the Stretch Index of Your Pool Table Cloth:
• How to Calculate the S...
How to Finish Your Pool Table Pockets the Right Way:
Advanced Method Custom Liner: • Fitting Pool Table Clo...
Basic Staple-Only Method: • Pool Table Cloth Insta...
How to Re-Cloth Your Pool Table Rails:
Basic Method: • How to Re-Cloth Your P...
Advanced Method, Simonis Cloth, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Install Pool Table Rubber Pockets:
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Calculate Your Pool Table Difficulty Factor (TDF):
Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Mark Your Pool Table (for Pool):
Basic Method: • How to Mark Your Pool ...
Advanced Method, Simonis Cloth, Olhausen Table: Coming Soon - Subscribe Now and switch on Notifications to be Notified when live!
How to Mark Your Pool Table for Snooker:
• How to Mark Your Pool ...
How to mark Your Pool Table for Snooker (Technical Considerations):
• Marking Your Pool Tabl...
How to Drill a Pool Table Slate:
• How to Drill Pool Tabl...
PLEASE NOTE: This video was originally produced for our General DIY channel (Fix Savers) before we launched our dedicated Pool channel (Average Joes Pool), hence the Fix Savers branding in the video.
VIDEO BY: Average Joes Pool/Fix Savers (all rights reserved)

Пікірлер: 77

@AverageJoesPool 2 жыл бұрын

Air Stapler: Amazon USA: amzn.to/47o9VFX Amazon Canada: amzn.to/46r3SiP Amazon UK: amzn.to/3RcNdeg T50 Staples: Amazon USA: amzn.to/40MVbyd Amazon Canada: amzn.to/49PFiew Amazon UK: amzn.to/47Kmb3r Staple Remover Amazon USA: amzn.to/3SYKmY1 Amazon Canada: amzn.to/3QS0RCl Amazon UK: amzn.to/46s3EI0 Worsted Cloth: USA: amzn.to/3e2eX1q Canada: amzn.to/3jl53L2 UK: amzn.to/3Iq2HYw Napped Cloth: USA: amzn.to/3NGG5Vt Canada: amzn.to/3VMymX9 UK: amzn.to/3CqFRfG

@jonmerritt6092 4 ай бұрын

Just wanted to say I just completed my 8ft snooker table refurbishment. Upgraded the rubbers, re-clothed it etc, and many of your videos have been instrumental in me being able to do that, so wanted to show my appreciation. Thank you :)

@AverageJoesPool 4 ай бұрын

Excellent! Glad to hear we were able to help you out with the installation, and glad that it all went well for you. Thank you for your support 👍 --- To help support us (for both you and others reading this) there are a few things you can do: 1) Please be sure to use our Amazon links in the Video Description! 2) Please Like our video's on KZfaq (by clicking Like!) 3) Please ensure you subscribe to our KZfaq channel! 4) Donations both needed and welcome! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq! 5) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@DawgsChamp88 Жыл бұрын

Thank you. I appreciate your time in teaching us this. I've seen a few good videos and they were informative, but you went into more detail. Which was perfect. Your narration is great. Like we were standing there as you taught us this.

@AverageJoesPool 10 ай бұрын

Thank you for your kind words, and really glad that we were able to help you get the job done! Thank you for your support! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@bryandollins6940 2 жыл бұрын

This video was very helpful and easy to understand. Thank you.

@AverageJoesPool 2 жыл бұрын

Excellent!! Glad it was helpful!

@jasontowne120 Жыл бұрын

Thank you VERY MUCH for making this and the other informative videos that you put together. I just acquired my dad's elegant pool table and I want to change the color of the felt. I was worried that I would have to take it to a professional to have it done but after watching your videos, I won't have to. You make the end results look as though a professional HAS done it. Thanks for the x-tra bonus tips scattered throughout your videos too. Will definitely be referring back to them again.

@AverageJoesPool Жыл бұрын

Thank you for the kind words, and really glad to hear you are enjoying our videos and finding them helpful! Best of luck with your cloth change, and hope it goes great! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@lenchstudios 2 жыл бұрын

Very nice and as a bonus its really relaxing to watch; keep it up!

@AverageJoesPool 2 жыл бұрын

Thank you, we really appreciate that :-)

@DavidKozinski 2 жыл бұрын

Very nice. Watching from Cleveland, Ohio. House flooded and final repair job is rebuild and felt the table.

@AverageJoesPool 2 жыл бұрын

Glad you found our video useful :-)

@yawbredulogah6446 2 жыл бұрын

Captivating it very much open for everyone to learn

@AverageJoesPool 2 жыл бұрын

Thank you :-)

@jasonh3109 2 жыл бұрын

Fantastic!!!!! Great videos thanks!

@AverageJoesPool 2 жыл бұрын

Thank you, glad you are enjoying our videos :-)

@tedspillers2252 10 ай бұрын

Excellent video, very informative, well done!

@AverageJoesPool 10 ай бұрын

Thank you, glad it was helpful for you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@josephhester8500 2 жыл бұрын

Brilliant video

@AverageJoesPool 2 жыл бұрын

Thank you, glad it was helpful for you :-)

@derekacres8122 2 жыл бұрын

Very helpful series! And thanks for sharing all the additional tips. Saved me a lot of time reassembing, refelting, and installing new rubber on the rails on my Hercules table!

@AverageJoesPool Жыл бұрын

You are so welcome!

@chuck_thebeard 2 жыл бұрын

Thanks. Great video!!!

@AverageJoesPool 2 жыл бұрын

Thank you, glad you enjoyed it :-)

@johndrisner1048 2 жыл бұрын

I'm glad I watched your video, now I get the pleasure of doing my rails again. Thank you

@AverageJoesPool 2 жыл бұрын

Thank you! And best of luck, slow and easy gets it done right :-)

@djc6323 Жыл бұрын

Good method for tables setup in a house not in a billiard bar where they are holding league games.

@Bill-le2dp Жыл бұрын

thanks for the info great vid

@AverageJoesPool Жыл бұрын

Glad it was helpful for you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@ryankessens8503 Жыл бұрын

Thanks!

@AverageJoesPool Жыл бұрын

Thank you for supporting us here at Average Joes Pool - it is greatly appreciated!

@user-wd2tp8id1f 8 ай бұрын

Thank You

@AverageJoesPool 8 ай бұрын

Glad we could help :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@JamesWells513 2 жыл бұрын

Love your videos! Just moved a pool table so your videos a going to make this job alot easier! Unfortunately I need to replace my pockets. Maybe I'm not looking hard enough but is there a video for that

@AverageJoesPool 2 жыл бұрын

We don't have a dedicated video for pocket changing, BUT how to fit (and so also remove) the pockets will be covered in our upcoming complete pool table installation video. Please ensure you have subscribed and notifications switched on so you'll get notified when it goes live in a few weeks! Thanks for your support!

@benstumpo5145 2 жыл бұрын

Great clips guys. I will be following these guides to level the table and recloth the table and rails My simonis 860 has the writing on edge of the cloth...IWAN SIMONIS 860 and the signature. With an 8ft table there is enough for the head and foot rails to have this showing on the angled cushions Do you advise to not use these (in case I screw up the dimensions and it looks odd) or would you advise to go for it....."why not?". Also I suppose there is another possibility. The reason it is there is to do exactly this (unsure if this was just to show genuity but it is supposed to be the edge that gets yanked, stapled and cut off). Obviously I have the complete cloth and need to cut the rail bits myself.

@AverageJoesPool 2 жыл бұрын

Yes, go for it! It will look nice will the logo rails. That's a logo you want on your table!! Take your time and measure everything very carefully first. Don't rush, think it out carefully, and double-check all measurements and you'll be fine! Best of luck with th install!

@benstumpo5145 2 жыл бұрын

@@AverageJoesPool many thanks for your advice. Unfortunately I have already installed the cloth and decided against it. In hindsight, I think it would have been fine. I found the rails to be far easier than I thought and easier than the table cloth to install. The cloth turned out really good. The middle pockets were heart wrenching. I have noticed that there is a small amount of slack around the middle pockets area. Nothing disastrous, but there are some waves there when you run a pushed finger around the area. Any advice for getting rid of that. IE, I would need to move one staple at a time to make any corrections to get rid of it, but which ones. From the table sides or directly below where ripples are on the curve of the pocket?

@TheJemster Жыл бұрын

Hi, I thanked you yesterday for successfully felt'ng my table. Is there any other trick to fold the felt for the corner pockets? I'm having difficulty smoothing the felt over the corner. I have so much material left it is leaving very thick creases.

@AverageJoesPool Жыл бұрын

Hey there! There's o real trick to it. As long as you have not overstretched the material, then you should not have excess left over and it usually folds well. It's important not to overstretch the cloth on the rails over the rubber bumpers, as this can lead to dead spots in the rubber rails (as explained in the video). Assuming you have overstretched and just kept things snug but not tight, then the fold should be possible. Just make sure the first part of the fold goes right up underneath the second part which will fold over the first. If the first part is not tucked right up inside flush with the edge, then when you fold back down over it for the second part then you could have too much material. Hope that helps!! :-)

@allenph2005 2 жыл бұрын

The center pocket method is easier to do. Can I apply the center pocket method to all the corner pockets since I'm not good at getting those wrinkles behind?

@AverageJoesPool 2 жыл бұрын

They are different and so do require a slightly different method/approach unfortunately. Stick with it, once you get the knack once the remaining corners get easier every time!! Best of luck with it!

@vito-9567 Жыл бұрын

Are all wooden feather strip the same size? I have to replace them on my Burnswick gold crown 3

@AverageJoesPool 11 ай бұрын

Unfortunately not, there are few size variations :-( --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@nategreen5410 Жыл бұрын

Any videos for replacing the rubber on the bumpers?

@AverageJoesPool Жыл бұрын

Not right now, but it's definitely something that we might look at in the future! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@robertbrisk9382 Жыл бұрын

Should do a video on repairing pumpers

@AverageJoesPool Жыл бұрын

Yes, that's something that we might do in the future, how to replaced the rubber cushion bumpers. Thanks for watching! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@_Lexusttv 2 жыл бұрын

What should i do when putting the new felt around the feather strip, the feather strip is really hard to get back into the grove and protrudes out. It fit nice (not to loose or to snug) without the felt in, but now it seems to hard to press down with the felt in. Should i try hammering it with the rubber mallet and block? Just dont wanna hit it to hard…

@_Lexusttv 2 жыл бұрын

I ended up taking the board attached to the rail off, the decorative peice that comes down to hide under table. With that off and the rail flat i was able to pound it in better, albeit alot of force was used but didnt ruin anything.

@AverageJoesPool 2 жыл бұрын

Glad to hear you managed to get it sorted! Yes, they can be pretty snug sometimes, but better that than too slack o course! Just remember if it had a cloth in it before, then it can have one again!

@JeffStringer-sc6by Жыл бұрын

At 14:28 I am not getting nearly as many wrinkles as you, i have tried bunching it up more and having another person help but I just cant seem to get wrinkles. Any tips or tricks to help me with this would be appreciated!

@AverageJoesPool Жыл бұрын

It can be tricky, and takes a little practice. Also different cloths can gather differently. What is the brand of cloth you are installing? --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@nolanreategui6004 2 жыл бұрын

Thank you for yo video

@AverageJoesPool 2 жыл бұрын

You bet!

@RobTaylorRTP 2 ай бұрын

I have 18oz accuplay cloth and the side pockets, when folded in this way, seem to be too much material and I fear they will deliver an uneven bounce on the pocket facing side. Do you suggest a different method for finishing the side pockets with a thicker felt non-worsted felt?

@AverageJoesPool 15 сағат бұрын

Hey there! The method remains the same regardless of the cloth thickness (weight). You could try playing around with the fold itself. If it's not crisp enough then you can get excess material. You could try putting a thin metal rule into the fold to push the material in deeper and nice a nice crisp and sharp fold. Hope that helps 👍

@syoungy763 Жыл бұрын

I've got brand new rail Ball bounce of great untill I put the cloth on then it doesn't bounce as good what am I doing wrong from UK thanks

@AverageJoesPool Жыл бұрын

Hi there! It sounds like you may have stretched the cloth too tight over the rail rubber. It is possible to 'deaden' the bounce of the rail if the cloth is too tight, so it is important not to fit it too tightly during installation, as explained in the video. Hope that is of some help!! :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@user-xf8rj4hg3w Жыл бұрын

ممتاز جدا

@AverageJoesPool Жыл бұрын

Thank you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@pejuanglegends123 Жыл бұрын

Sir, I want to ask what kind of floor do you use?

@AverageJoesPool Жыл бұрын

For this tables installation the floor is concrete. Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@Oshane_smith19 Жыл бұрын

What material is used at the end of the banks

@AverageJoesPool Жыл бұрын

At the end of the rails you have the cushion facings, which are seperate from the rail rubbers. You can buy the cushion facings seperately from the rubbers, and they are pretty cheap too. You can buy them on Amazon for around $10 for a set of 12 - take a look here: amzn.to/3X2Xh9Q --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@ramedohrnitram1027 Жыл бұрын

Very nice demonstration and very informative but too much talk.... But so much appreciated episode. Thanks .

@AverageJoesPool Жыл бұрын

Glad you found the video helpful :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@codypoole3432 Жыл бұрын

All of your videos have been helpful to me except for this one. I can’t figure out the corners at all. Not enough info on how to do the corners. I have about 3” of felt hanging over each side of the rail. Am I suppose to cut the felt flush with the ends or an inch hangover or what? Bc I can’t get the first fold figured out

@AverageJoesPool Жыл бұрын

Hey there, sorry to hear you are having issues. The folding for the ends is covered at 17:02 and 22:35 onwards in the video. Maybe you have a different type of rail to the ones we are working on in this video?? Do your rail look identical to the ones in the video? All of the info you need is in the video, which is why I'm thinking maybe you have a different rail type? There are a few variations, what we have here is probably the most common type for home tables. We hope you get it worked out, best of luck!!

@jordaneischen9924 Жыл бұрын

I had trouble with the corners as well, you kind of just have to feel it out, taking up the excess material little by little underneath on the staple side, while focusing on smoothing out the cloth on the rail, if it starts to wrinkle on the rail, back up a bit until it’s smooth, add a staple, repeat.

@aleanufopilotftlcertified5663 Жыл бұрын

@ 13:27 to @ 14:27 I thought you somehow damaged your fingernails. I had to go back and listen and sure enough you mentioned that your partner's help was appreciated. His painted fingernails are very pretty. So this video can be titled rails and nails recovered.

@AverageJoesPool Жыл бұрын

Lol, like it 🙂

@pejuanglegends123 Жыл бұрын

Oh sir, how much does it cost?

@AverageJoesPool Жыл бұрын

Hey there! How much does this process cost? Well this video is designed to show you how to do it yourself, but if you wanted a professional to visit your home and re-cloth your table it would likely be several hundred dollars. The prices do vary quite a bit, anywhere from $200 lower end to $600 upper end is realistic (for the full table). Hope that helps! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Average Joes Pool without the support of people like you! You can donate by PayPal - just go to www.paypal.me/thanksfixsavers - or alternatively you can click the SUPER THANKS icon under the video on KZfaq and donate that way too! 2) Please ensure you subscribe to our KZfaq channel. 3) Please Like our video's on KZfaq (by clicking Like!) 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

@pejuanglegends123 Жыл бұрын

The video is very helpful

@pejuanglegends123 Жыл бұрын

Oh, sir, how do you cast concrete, what are the ingredients, if you have time, make a video on how to mix the ingredients