Great video, I have to do the same thing to my 09 heritage Softail. You were very detailed, and made it a lot less intimidating. Thank you.
@edshort77303 ай бұрын
Good video , You made it look easier then it really is. I have done these on many makes of bikes and seen many people Fail trying it themselves and they end up calling me to help them get it back together. Floor jack and vice trick was even new to me . Thanks for all your videos you post !
@Riff777 ай бұрын
Great Tutorial. I especially liked the inner tube/Press Jig/PVC hacks. Great stuff for those of us who have not done this 1000 times.
@fredk56736 сағат бұрын
You awesome 👏 thank you for the video
@bpbigdeal197728 күн бұрын
Made it look real easy where you at I’ll bring you mine
@WitchcraftCycleWorks28 күн бұрын
It's really not that difficult. The first time is always the hardest.
@retiredrandy83014 ай бұрын
Great video. I was wondering how I would compress my spring on reassembly. Floor jack solution is genius. Thanks for sharing.
@curtgarrett7067 Жыл бұрын
Nicely done, very thorough
@87ricer Жыл бұрын
Tripod Brotherman .... my uncle helped me with the forks on my 98 vstar 650 he really helped me make that motorsickle a fantastic running updated bike for my first large bike ...... you've done it enough that it definitely looks easy thanks for sharing this is gonna help
@musicmansride Жыл бұрын
Great tutorial. I may be tempted to try my own when my seals go bad.
@dalerobertreid1318Ай бұрын
Thank you grate video
@jazziejerry6248Ай бұрын
Great video ill definitely be referencing this video when i do mine. I was told sometimes the seal gets curled and you can reach in with a small pick and pull it back in position is this a thing that you ever run into, this is before rebuilding but noticing a little oil.
@WitchcraftCycleWorksАй бұрын
I've never had a seal curl.
@SaddleTrampTV10 ай бұрын
Great instructional video, Bill!
@WitchcraftCycleWorks10 ай бұрын
Thanks. Just trying to teach people that you can do repairs yourself.
@rdbjr5210 ай бұрын
Thank you for the video. Well done!
@richardcolozzi64254 ай бұрын
I like the improv. Tripod is handy
@askthisoldtileman826411 ай бұрын
Great job
@craigeby80162 ай бұрын
So great video. im thinkin we both have a drawer that looks the same full of Harley specialty tools lol. Any ways right at the end you filled it with oil then went to put it on bike then this black rubber seal appeared what was that and is that for the softail models? im getting ready to rebuild mine as soon as my kit get here. looks straight forword enuff. but was just curious to that last seal coz you never mentioned it going on. its at 19:54 in the video
@WitchcraftCycleWorks2 ай бұрын
That's just the seal that I installed earlier,the lighting makes it more noticeable. I didn't add anything extra between frames.
@breez6502 Жыл бұрын
I got a question for you. I ride a ‘09 heritage. I’ve had medical issues with ankles so haven’t ridden in a bit. Checked the oil the other day….look very low. Filled up to fill line cold. Today ran the bike until hot, checked the oil. Now I’m way above fill line hot. Is it best to check when hot vs cold? I’m mechanically inclined when it comes to trucks….Harley’s are a different ball game.
@WitchcraftCycleWorks Жыл бұрын
Did you check the oil level before you fired it up? If so, the oil may have "sumped". If they sit for a while, oil can seep past the oil pump and collect in the engine. The oil in the tank will show low but when you start it up the oil collected in the engine will push back into the tank. I always check the oil level after running the bike for a few minutes. You can check it cold or hot as most dipsticks have both levels marked on them.
@JohnCacace-cw2tr Жыл бұрын
Great content. Looking to do my 04 Wide Glide with the same forks. Questioning the Drag Specialties parts. Heard the aftermarket stuff is not the same as the O.E.? Fork seals not as thick as originals etc. Did you match all the parts up? Did everything look the same? Thanks again for a great video
@WitchcraftCycleWorks Жыл бұрын
Thanks for the response. I haven't had any problems with the Drag Specialties parts. They looked good and fit just like the OEM parts.
@JohnCacace-cw2tr Жыл бұрын
Appreciate the info
@ericmacdoud493511 ай бұрын
thanks, j'ai mon écrou du haut qui s'est dévissé, vos explications vont m'aider. merci c'est cool..
@adamaaron71843 ай бұрын
What size wrench are you using for the pinch bolt? A 5/8 fits but is pretty loose. I just don't want to round the head