HOW TO REMOVE GAS CYLINDER LIFT AND WHEEL BASE FROM OFFICE CHAIR
Пікірлер: 49
@mightymag921 күн бұрын
great instructions, after buying a new gaming chair that is far too low, and ordered a new gas lift this was great instructions
@stevenowens4511Ай бұрын
Hope the following tip is useful to others: Long story short, if the pipe wrench is not budging the old gas piston, get a blow dryer or a heat gun (basically the macho tool version of a blow dryer) and point it as the base of the gas piston (i.e. where it enters the seat) for a good 10-20 minutes. I'm in the middle of doing a gas piston replace on a second chair, and I had hoped it would be easier than the first, but it looks like I'm going to have to pull out the blow dryer again. As other commenters have said, I tried all the obvious tricks. My pipe wrench actually cut GROOVES in the metal of the old gas piston. The blow dryer worked. I'm still not sure why. Obviously metal expands when it heats up, maybe some combination of that expansion breaking the seal, or just forcing the hole to widen, or the heat softening the plastic sleeve it slots into. Any way you slice it, it worked.
@D.L.-fg5fb2 ай бұрын
Thanks, you saved me time from trying to figure it out.
@watch2learnmore Жыл бұрын
I tried other instructions on how to separate the wheelbase and the cylinder, but it wouldn't budge. I found your video and your tip about popping the clip on the bottom of the cylinder was the missing piece of the puzzle for my Dormeo Bristol Octaspring chair. I followed the same steps on the new cylinder and was finally able to successfully remove the old one and install the new one. Thanks so much!
@Nick.T-Alo.G-Car5 ай бұрын
Many Thanks for the clear instructions without any beating about the bush - greatly appreciated.
@how2not225 ай бұрын
You are welcome!
@whisky37Ай бұрын
This is the exact chair I needed to do this on lol. Amazon returns should forward this video to people and pay you for it.
@ilinpang2750Ай бұрын
Thank you so much. What an extremely helpful video. It worked just as in your demostration. Life saver!!
@how2not2224 күн бұрын
Glad it helped!
@resilientrontu Жыл бұрын
I bought a chair from amazon and couldn't separate it to fix it and your video helped a lot. We also used a little bit of oil inside and it worked perfectly. Thank you for the amazing video.
@how2not22 Жыл бұрын
Glad it helped!
@weniweedeewiki.6237 Жыл бұрын
You know how long i have been waiting to find a video that explains this to me ..........your a star thankyou.
@uriituw Жыл бұрын
Who possesses an “a star”?
@industrialgearheads87302 жыл бұрын
Thank you for the video and explanation. This helped a lot.
@bladegomez5849 ай бұрын
Thank you😭😭😭 The wheelbase removal part saved me😭😭😭
@pawandeep3111 ай бұрын
This helped my put the hydraulic cylinder back in place! Thanks a ton!
@how2not2211 ай бұрын
Glad it helped!
@tildeathgaming9510 Жыл бұрын
I’m lost you deserved a subbed thankyou!
@timchrstoffer3304 Жыл бұрын
This was just what I was after! Thank you!
@how2not22 Жыл бұрын
Glad it helped!
@Alskasaur28 күн бұрын
Thank you so much! Had to send a chair back after putting it together and the base wouldn’t fit back in the box but I couldn’t get it apart!
@how2not2224 күн бұрын
Glad I could help!
@grimos1719 Жыл бұрын
thanks for the video. i was having a hard time to remove and replace the cylinder ffs but thank you again.
@how2not2211 ай бұрын
Glad it helped
@danking41289 ай бұрын
Nice, it worked! Thanks a ton!😆
@ananyaroy5609 ай бұрын
You are a LIFE SAVER!!! ❤❤❤
@rem427712 күн бұрын
would a rubber mallet work instead of a hammer?
@SerRageALot6 ай бұрын
No matter what I did hitting it or trying to get a wrench to do it the gas cylinder would not budge whatsoever but thank you the video was helpful for everything else though
@thereyougosir11 ай бұрын
You saved me! You're amazing 😊Thank you very much 🎉
@how2not2210 ай бұрын
You're welcome!
@supergeek12 жыл бұрын
Well done.
@darkpistol9610 ай бұрын
thanks, helped a lot
@notlucas6859 Жыл бұрын
you saved my life
@isruler Жыл бұрын
you saved me big time
@menagajaikumar2493 ай бұрын
THANK YOU
@roosebelt99616 ай бұрын
Gracias
@tylertr9 ай бұрын
By heat do you mean from a hair dryer?
@Skreppatada7 ай бұрын
I LOV U THANK U
@lyez71077 ай бұрын
Do I need the orenge thing
@thewindwhisperer68394 ай бұрын
Nice Like :D
@PR_BlackMamba10 ай бұрын
Ooo ooooo oooOmagadd
@robertogodoybacaarauz39272 ай бұрын
What's the size of the cylinder please.
@LtSoap Жыл бұрын
Thank you
@how2not22 Жыл бұрын
You're welcome
@MarketOracleTV Жыл бұрын
LOL, you destroyed the chair, so many needless steps
@sans9822 Жыл бұрын
this is so wrong in so many levels, you do not hammer the gas lift and you do not need to remove that clip, there are no serviceable parts in it. use a rubber mallet to hammer the base of the chair while holding the gas lift to remove it.
@ashleysilver5594 Жыл бұрын
But she appears right. That clip was holding the end of cylinder to the wheel base.
@chlonez Жыл бұрын
Its not wrong, just taking extra extra step
@Francheska29110 ай бұрын
the onlt right you said is using a rubber hammer but her step is more safe because you are taking out the parts of a cylinder that can explode if you hammer it wrong specially the beginners