Great job Tim. Three years later and your video is still helping people!

Two years on the repair is nearly invisible and is holding nicely. Great investment in an inexpensive kit that solved my problem following these steps. Highly recommended.

You get a 10/10 for just taking the time ana show us how! THANK YOU.. I personally benefited from your video!

This video was uploaded 4 years ago and still relevant today. Thanks.

One of the best instructional videos on KZfaq. FIVE years later and still helping folks like me. Good job!

Bought same kit, no push pin, no alcohol swab, and no straight razor. The video was well done.

Great video, thank you! The instructions included were difficult to follow. Thanks for sorting it out and making it easy and understandable.

Just bought the JB Weld version and this was the best video I could find to apply the application. The contents is exactly the same as well as the instructions. Thank you for the step by step. Super helpful.

Thanks for this simple and easy to follow clear and clean video!

Thanks for the vid. I'm glad I found it. The instructions are overwhelming. I encountered a few issues though. Cut the tip of the resin, don't just twist it off.

Appreciate the step-by-step process! There's just something about the little paper with picture instructions that I hate .

I just used this kit on my 23 year old Chrysler which got a classic bullseye chip. Similar to professionals I preceded the application by holding a 30in vacuum with my HVA/C vacuum pump for 20 minutes in order to extract all traces of moisture from inside the chip. I had to do this because the damage happened on a winter's day with lots of snow, sleet and ice impacting the chip before I could get to this repair in a dry area. Its winter in Canada now so little sun and the outdoor is too cold to do this outside so did this in my garage and used a UV flashlight. I also followed two pro tips: after filling with resin, warm the glass from underneath with a hair dryer and rap the area below with your knuckles to encourage the resin to thoroughly flow into the cracks. The main chip is now invisible, however there is still a tiny scruffy area where the stone hit. If you have left over resin, you can add a drop to that spot and cure it again in the sun.

A very helpful video and step by step clear instructions!

Thank you! I had to do this to my van ( actually the same exact van and color as you 😂 ) this morning, and I had no idea what I was doing but after I watch your video I just followed it step-by-step!

I was sceptical at 1st when I tried it but it gave amazing results and would definitely use it again.

Thanks Tim. You did a very professional job of demonstrating the repair job and producing your video.

Thank you! Just fixed my car`s windshield today and your video was a big help!

This video is super simple and to the point. Thank you!

Instructions were easy to follow after watching the video We had trouble locking the syringe but it didnt affect anything else. The work came out great.! Thank you.

Thank you so much for this, made fixing the chip on my windshield super easy. For anyone else who is curious, you can re-use the plastic seal and epoxy on smaller nicks like the one at 1:00. Just use the tack to clear any glass and start the process from 11:10, did this on about 5 nicks with the leftover epoxy and it worked amazing.

Primary purpose of the kit is to seal the cracks so that it can't expand and make a minor repair that costed 10-14 dollars, for the kit, into a 700-1000 dollar windshield replacement. Hiding the chip/crack, or even making it smaller is an added bonus from the repair kit.

Thank you so much for this useful guide! I’m going to do this for £5 with a kit from Ebay, instead of going to a garage and paying £40

Simple and covered all the steps... perfect!

very informative i also had a crack mine was a half moon crack this product actually works :) lesson learn don't get to close to trucks or semis

Thank you Tim. Great video and I just repaired two chips with excellent results. Thanks for your time and effort!

Thanks for the tutorial. Now l know what Not to buy. If you use a sawing motion it is less visible.

The year is now 3017. All remnants of this vehicle have deteriorated except for one; the windshield. The verdict is in…this stuff really works!

Great video man helped me out allot saved me 50 dollars deductible! I had a chip on the same area down there by the defrosters vents

Wow I loved your video, easy listening, calm, instructive, not bought out from the company to push that product, BRAVO ZULU, above and beyond your duty to help the world understand a little thing. Thank you. Positive daydreams, love and sunshine

I used this and it really worked I seen the difference after 20 mins

Just finished mine. Not sure how it will hold up yet but it came out fantastic. 10/10. Much cheaper ant at least as good as the professionals. Had to do my own as I am always working when the shop is open.

Such a great tutorial much appreciated 🙏🏻

The instructions and even the company video were horrible. I like your simple explanation better. Thank you. Waiting for my resin to finish with the plunger part as I type.

If you are on the fence whether to have this done professionally or not ,take my advice and do it yourself. Just paid $85 to fix a chip that was 1 inch . It is now 3/4 . The only difference in the two methods is the guy drilled a hole with a Dremel tool halfway through the glass before starting which probably was the reason it still shows.

great explanation, just did my window and it worked great

just bought this kit, not really caring about the looks but not wanting my rockchip to turn into a crack and have to replace my windshield later on

I used this video 3 diff times now lol

I just bought this from Amazon. I pray mine looks good like yours.

Oct - 2021 .still works this vídeo !

I've have just successfully used the permatex system for the second time after 1 good permatex last year and having 2 versachem kits that are basically the same components (my versachem had all the same parts except differently colored 2 sided tape, no pin, no razor blade, no alcohol swab which cost $16.99 vs this kit for 15.99) I have noticed that peeling and applying the colored backing side to the windshield first seemed to have a more tacky glue than the paper side which I left up to apply the pedestal to. If you run your finger across the end of the tab, whichever backing is more difficult to remove is probably best down to the glass. . .IHMO

I just used the kit. Worked great

Tim! Lol! Global Travel Bud! Whoa! I literally was just on the highway and this big rock hit my windshield. I had to pull off at the vitamin shopp to find a fix it yourself video and your windshield repair video came on to help me fix it! Wow! You cannot make this up. You traveled with Crossroads? Maybe I have the wrong Tim but thank you for the video 🙌🏻🙏🏻👏🏻👏🏻🙌🏻. Divine intervention for sure Blessings Molly

I just got hit by a pebble and I’m thankful I use this right away and it’s still shows but it’s better than replacing the whole glass when it start cracking more

Thank you.

Thanks for the video helped out a bunch.

Thanks, your instructions were better than the mfgs. video.

getting ready to do the same thing..... appreciate the video

Thanks for the time Tim !

Thanks, I got a chip today and now I have to do the same thing

Thanks Tim helped me out a lot.

I agree that it was very hard to pull it up. I didn't have that much bubbling, though.

Used these a lot with good results.

thanks, i tried it and it worked excellent. follow the directions... push that resin down so it goes in , i made a small mistake in this area... now I can sell the vehicle and no one will know

Thank you!

That was super awesome guide. Thank you so much. More clear than the instructions

Thanks a million Tim!!!

Thank you so much for this video! It super help me today

from watching all the bubbles coming out you didn't have a complete seal and lost the vacuum before pressurizing it to force the resin in. Only a few bubbles should come out as there is so little air in the crack and fixture. It needs the vacuum to pull the resin all the way in for an almost undetectable fix. I always put a bead of silicone around the edge of the fixture and where the syringe mates after attaching with the double sided tape seal to make a good seal (the silicone does not need to cure to seal) It should bubble for just a few seconds, if it continues to bubble it is not sealed. I also put a drop of oil on the rubber plunger seal from the plunger side for better vacuum holding.

thankyou TIM it help me to repair my windshield

I have a question : The last step, when he said that he was going to add a drop of Epoxi, he was refering to the Resine he previously used it ? I didn't see other products beside this one. Is this correct ? By the way, very very clear instructions. Thank you. I will try it after receive the answer to my question.

Thanks !!!! Great video !!!!

Who else blew into their phone when he used the pin to pick the loose broken glass??🤣

the air bubbles you are seeing with the syringe in upward position are from a poor seal. No way possible to have that many bubbles/air coming from a micro crack in the windshield.

Thanks for the great video,👍👍

Thank you so much!

7:20 at this point heat a glass from inside with cigarette lighter or heat gun. it helps to remove bubbles ;)

Good job

Very helpful Much appreciated

This is my 7th time watching this tutorial despite having previously completed six repairs 🤣

The kit bought doesn’t have a razor or pin. Everything else is identical

Awesome dude 👍🏽👍🏽

He got his nails done he got a manicure he's got a movie star hands he's a model the hands model he's got beautiful hands I love his hand hand job give a good hand job

Amazing video, thank you so much

Awesome job!

Really helpful thank you

people who need a razor typically have a few laying around. things like face hair, razor replacement blades and self loathing come to mind; a few relevant reasons to have blades even in 2020.

It filled mine clear but as soon as I used the razor to scrape off the excess it left a white dot where the impact was. Why?

I am so glad SC has free glass replacement. i couldn't stand that spot.

Lol, says clean around it, I'll just go ahead and clean all of it.

Thank you. That helped a lot!!

cool video

Any tips on doing this in cold weather? I know it says to do it in 70 degree weather but it's December in the east coast and I need to get this done before it gets really cold in january

What if you mess up? Can you buy another kit and re do the repair?

That kit says for bulls eye. You have more of a star burst and Angel wing type damage. Should you have gotten a different resin kit to match your damage?

Thanks

Jello Tim, if there was somthing different in the process what would you have done ?

One would expect the resin to be sucked out with any air too.

thank you for that.

Thanks for the video...

It’s super cloudy all the time in the Pacific Northwest. Would it still work the same do you think?

About to do this myself g ot 2 lil chips from rocks they ben there 3 yrs never addressed them but just bought this same or similar kit to try it , The syringe is just to pull out the air? Not to push the resin in ? That part confused me I thought after the resin was in you'd use the syringe to force it into the hole but looks the opposite you just pull it to get air out? Odd,,If it works on my windshield may try my ipod next . By the way any info on the black rubber mold that is between the windshield and car itself ? Half my rubber is off tried glueing it 3x still pops off in coule days , any advice on that be great too

Thanks a lot! now I will have to replace my windshield. The step to place the applicator on the window and remove the bubbles, I watch the crack extend 2.5 inches. Thanks a lot! Please remove this video. DO NOT PUT ANY FORCE AROUND THE CRACK!

hi there, i’m holding out for my car windshield replacement and the crack is about 12 inches; i actually have two, the other is 10 inches.. they are on the far side of the windshield, not the center… do you think this will be okay until next friday ? that is 10 days from today. The kit i bought is what you have here -

May not work in tropics....glue does not hold the plastic pedestal when add pressure back with syringe, so resin did not reach inside the cracks and spilled out. Adhesive disk did not come out from windshield, so the issue was the glue between the disk and plastic pedestal.

GREAT VID ! TY

That was a lot of air that came out with the syringe. I think the black seal had an air bubble in it. Not a big deal but a better seal might have covered the crack more. One tip is to tap the inside of your windshield to help get the bubble out when the syringe is on. Also you were suppose to squeegee the top of the plastic seal at the end to further remove air bubble for the final seal. That would of filled whatever little cracks were left on the surface.

Hey I did this at night does it really matter? I’m in Wilmington NC not to far from you

What if there is a small crack also along w the chip scan that repair it

I was sceptical but this kit actually works

Wow perfect video I.manage to do it perfectly