How to repair Ford and Mazda power steering racks

Рет қаралды 91,905

6 жыл бұрын

Learn more here: servicems.eu
In this video we will consider how to repair hydraulic rack FO 209 for Ford Fiesta V, Ford Fusion, Mazda 2. We use the test bench MS502M and special repair tools in the process of diagnostics and repair.
MS502M - servicems.eu/for-diagnostics-...
Special repair tools - servicems.eu/special-repair-t...
Original numbers:
1336686, 1351310, 1351610, 1352973, 2N113200AF, 2N113200CA, 2S613200KF, 2S6C3200KN, 4329684, 4344071, 4356872, 4358909, 4374700, 4386252, 4387041, 4397223, 4452242, 4472936, 4472938, RF2S6C3550KD, VR256C3550, 1667686, 1352976, 1631754, 2S613200MB
______________________
👍Follow us:
- Instagram: / msg_equipment
- Facebook: / msgequipment
- Twitter: / msg_equipment
- Linkedin: / msg-. .
_______________________
If this video helped you out please don't forget to subscribe, give it a thumbs up. Thank you very much for your support!

Пікірлер: 30

@MSGEquipment 6 жыл бұрын

More information you can find on the website servicems.eu/for-diagnostics-of-power-steering-system

@cuttheloop 2 жыл бұрын

I just happen to be shy a few (all) of those tools...

@dougwagner5724 4 жыл бұрын

So simple, any home mechanic can do it...

@tiny_toilet 4 жыл бұрын

My lathe can only do circles - no triangles, so guess I'm outta luck.

@MSGEquipment 3 жыл бұрын

It`s just only a fisrt sight.

@skip741x3 Жыл бұрын

LOL yeah we all have those fancy tools and lathes dont we?

@munyaradziallan9173 5 жыл бұрын

is the Mazda 2 steering rack same as the Mazda Demio steering rack

@paneerselvan8198 3 жыл бұрын

Good informative video

@MSGEquipment 3 жыл бұрын

Thank you for the feedback!

@InfiniteGamerGaming 3 жыл бұрын

How would I fix a rattling noise in my 2005 mkII Ford Focus 1.6 petrol? Noise is on the steering rack

@CHEAPROLLIN 2 жыл бұрын

My steering used to bind now it has no powersteering at all. It had a new pump put on. Still no power steering. I pulled the steer shaft but it would move great also the pump will bubble every couple minutes when in the air turning wheels..... I used trans tune in pump now. It has a lot of metal flakes in fluid. the vehicle is an 06 ford freestar with no power steering. WIll this rack unclog if I put a little gas in it( I seen this online) if not what do you think my issues could be and any idea how many hours labor or total cost? Please help sorry for novel

@reybexn 4 жыл бұрын

Is this the same with focus 08my

@eddyboh2723 9 ай бұрын

One question: I accidentally polished a small segment of the anti-rust zinc coated surface of my steering rack: How do I recover the area I accidentally polished?

@ebdcauto-technicsconsultin9862 4 жыл бұрын

I didn't see adjusting of the pinion pre-load and the final pre-load (rack against pinion) on the yoke side cap nut. The rest all good.

@MSGEquipment 3 жыл бұрын

This part was lost during the video prepearing.

@CHEAPROLLIN 6 ай бұрын

Whats the tool for 4 pin nut

@prostmahlzeit Жыл бұрын

What is the part number of the Piston ring at 3:38?

@zexzaidi8291 2 ай бұрын

I assume No grease is needed there.

@Anthonythesider Жыл бұрын

My pre load is leaking on mine

@user-nh4fo7qs2h Жыл бұрын

Me gusta

@user-eo1nk6gm6b Жыл бұрын

Смазка где

@mdsaiyadkhan9263 3 жыл бұрын

Hii

@mdsaiyadkhan9263 3 жыл бұрын

Mere ko bhi steering Banane aata hai kahan per hai garage batao

@MSGEquipment 3 жыл бұрын

Thank you for the interesting of MSG Equipment. Please contact us - use this form: servicems.eu/contact-us. Or servicems.eu/content/contacts. Our managers let you know about conditions and sheeping for your region

@MrTravisAl Жыл бұрын

“Step 13 get help from machining lathe operator.” I wish i were hyperbolizing / exaggerating…. Damn. well that puts a damper (no pun intended) on the plan to rebuild this steering rack and pinion.

@adematthewsracing Жыл бұрын

You can do that step with a dremel or a combination of file/hacksaw. I've done all three methods. Lathe is easiest and quickest but not the only way. Of course you only need to do that step if you have worn seals. Most of the time I'm converting these racks to manual so I just cut the whole thing straight off.

@prostmahlzeit Жыл бұрын

@@adematthewsracinghow do you put that big metal ring back on without a lathe? In the video it looks like they use a new big metal ring that gets compressed on the edge to get fixated on the rack

@adematthewsracing Жыл бұрын

@@prostmahlzeit Generally I don't put one back on as I convert the racks from PAS to manual so it's not needed. Looks to me as though they're just pushing it on rather than doing any sort of machining on it. You could do the same with a floor mounted press or a drift and hammer especially with a bit of heat.