I couldn’t find a tutorial so I made one myself on my 1995 cd5 Honda Accord
Пікірлер: 32
@frankrizzo3025 ай бұрын
Thanks for your help
@philztheone5 жыл бұрын
You are my hero! Thank you!
@artsmart07 Жыл бұрын
anyone watching this , it was reassembled incorrectly. It is suppose to have the very center spacer between the two center bushings/washers which he did not put in.
@tlak Жыл бұрын
The curved part of the washer is supposed to be against the bushing.
@lochzoch898710 ай бұрын
It’s been like this for 6 years no issues
@tlak10 ай бұрын
@@lochzoch8987 Probably wouldn't be any problem just the washer is suppose to cup the bushing.
@cherryblossomscarletokami98417 ай бұрын
i know its been awhile since you posted but i wanted to thank you, as i was trying to find a CD5 specific, thats an EX, because they say the rear sway bar is slightly different on the subframe side of things than LX/DX
@lochzoch89875 ай бұрын
Lots of different things going on with the back end between LX and EX.
@billythekid71223 жыл бұрын
You did a good job I normally loose my Lugnuts just slightly before I Jack it up
@lochzoch89873 жыл бұрын
Big brain
@tek6303 Жыл бұрын
link to bushing kit?
@lochzoch89874 жыл бұрын
Correct term my wrench is hitting the strut fork not knuckle
@annhenry12262 жыл бұрын
u didn't use the spacers off the old one ?
@lochzoch8987 Жыл бұрын
No they sucked
@lochzoch89875 жыл бұрын
If you have synthetic grease it’ll be better than lithium grease. Or even better anti-seize. At the time of this video White lithium was the only grease I had.
@killer2572964 жыл бұрын
Are you not supposed to lube up those bushings so they don't squeak?
@lochzoch89874 жыл бұрын
The Soviet Pinecone they’re polyurethane, energy suspension has some kind of lubricating properties embedded into the material
@lochzoch89874 жыл бұрын
Prothane
@corbinpeacock87222 жыл бұрын
This helps me with what I needed. But I hate that you put 9/16 on a car that uses metric.
@lochzoch89872 жыл бұрын
It’s what the kit came with 😵
@andrewpena7582 жыл бұрын
What’s the reason this part was change?
@lochzoch89872 жыл бұрын
The rubber ones rotted and caused failed inspection
@kinglouiethelast71642 жыл бұрын
God damn that’s a lot more rust than I’m used to seeing. Where are you from?
@lochzoch8987 Жыл бұрын
PA LOL AND I ONLY HAVE 70K on THIS BITCH
@daniellucero46873 жыл бұрын
Just to let you know your car is a automatic its in park and front wheel drive. so you didnt have to put the brake on before loosening it just saying
@lochzoch89873 жыл бұрын
The park Pawl prevents both wheels from moving But due to the nature of the differential still allows one wheel to spend in One Direction while simultaneously rotating the opposite wheel in the opposite direction. You can try this yourself, jack your car up and try to spin the wheel, it will just spin the opposite wheel. Park only prevents both wheels from spinning in the same direction.
@_FORBEZ_3 жыл бұрын
Pretty sure ya washers are upside down
@lochzoch8987 Жыл бұрын
WHO THE HELL CARES
@GrindBass8610 ай бұрын
This is unwatchable.
@lochzoch898710 ай бұрын
Perhaps you finding difficulty in watching a tutorial how to loosen a bolt and a nut speaks more about yourself than it does about the quality of my video.
@GrindBass8610 ай бұрын
@@lochzoch8987 Watching isn't the issue, it's listening to the constant noise of the camera being fumbled around.
@lochzoch898710 ай бұрын
@@GrindBass86 that could be blamed on the ridiculous $100 otterbox phone case I had at the time I made the video. Useless junk.