How To Replace 79 Series Landcruiser Rear Leaf Spring Bushings

No video

How To Replace 79 Series Landcruiser Rear Leaf Spring Bushings

Рет қаралды 29,251

3 жыл бұрын

In this video I replace the rear spring pins and bushings on my 79 series Landcruiser.
Disclaimer, I may be a qualified mechanic but I hold the right make it up as I go and am not held responsible for issues arising from advise given in these videos. All mechanical repairs should be carried out by a qualified professional.
#79serieslandcruiser #Camshaft #shacklepinsandbushes

Пікірлер: 46

@robertrayner2991 3 жыл бұрын

Just the video I needed - replacing my bushes today after watching this. Cheers

@CamshaftFM 3 жыл бұрын

No worries mate

@hdj81Vlimited Жыл бұрын

those bushing were still very good

@theman8447 4 ай бұрын

You introduction music is like that malaysian new agency 'kinitv' / 'malaysia kini'.

@barnziee7319 10 ай бұрын

I did this over the weekend ass well Changed the whole rear springs out. What a C of a job!!!

@CamshaftFM 10 ай бұрын

Haha yeah a bit like that sometimes

@jonnykrivan6840 2 жыл бұрын

Great vid cheers mate

@skboog 2 жыл бұрын

Cheers for showing the whole process with some helpful commentary!

@CamshaftFM 2 жыл бұрын

Thanks mate

@skboog 2 жыл бұрын

@@CamshaftFM no worries if you happen to do your brake lines anytime soon that would be helpful also

@nellmarshman1204 2 жыл бұрын

im on me mums lappy, thanks for the vid no ginning around get in and get it done, saved me heaps of time,

@CamshaftFM 2 жыл бұрын

cheers mate

@niceguy100000 2 жыл бұрын

I just replaced pins with greasable ones on my HZJ79. I did not use two jacks. 1) Jack up the rear pumper until the wheels barely lift off. 2) Put jack stands as high as they fit under the frame as in the video. 3) Lower the jack little by little until the jack stands are partially loaded. 4) Tweak the height of the jack until springs feel mostly unloaded and pins can be hammered and pried out semi-easily. (When hammering pins, put the nuts on as not to hammer on the thread. Because I didn't trust all of this much, I did not lay under the car for the whole work.). My pins were very dry even though the car has 8000 km.

@thomassullivan1526 2 жыл бұрын

Great clip mate very helpful how was the front wen you went to line it up for bolt to go in that’s my biggest worry!

@CamshaftFM 2 жыл бұрын

Thanks mate. Yeah there is always a bit of fiddling around but it wasn’t to bad

@williamgarrett8587 Жыл бұрын

Great vid, Mate. How do the greaseable pins work in the front of the springs, where the steel sleeve looks like it will keep the grease from entering the gap between the bushings and instead just push out either end?

@CamshaftFM Жыл бұрын

Yeah that’s what I thought too but with out the steal insert it’s too loose. I don’t think it’s that important for the front ones as they don’t pivot as munch as the rears.

@buzzlightyear2490 7 ай бұрын

Like to ask, are 1 ment to pump greese into before doing final tightening. Great video champ

@CamshaftFM 7 ай бұрын

Thanks mate and yes.

@sebbrown8860 Жыл бұрын

Hey mate great vid. What shackels are they?

@CamshaftFM Жыл бұрын

Thanks mate. Not sure they were on the Ute when I bought it

@jamesware8020 Жыл бұрын

Great vid cam. Did mine last week and your guidance was first class. Cheers. As an aside was wondering if you may be able to help me. My rear fuel tank won’t release fuel but the rest of the system is working fine. Any ideas mate. Cheers

@CamshaftFM Жыл бұрын

Cheers mate. Might be a blockage in the hose or the electric valve that lets fuel flow from the back tank might not be working properly other than that I’m not too sure iv had no issues with my one.

@jamesware8020 Жыл бұрын

Cheers mate

@jamesware8020 Жыл бұрын

Cheers mate

@jamesware8020 Жыл бұрын

Cheers mate

@jamesware8020 Жыл бұрын

Cheers mate

@stevenatkinson7391 Жыл бұрын

Did you use a torque wrench to do the nuts ? If so how tight please

@CamshaftFM Жыл бұрын

No I didnt. you can probably find the torque value on the internet though.

@lornebonnell2007 2 жыл бұрын

I've just had my rears done cause they were splitting, i've just done another 3000Ks lots of dirt and one of them is split again, any idea on a cause?, its OME sperings and shockies, replacement bushings were not OME

@CamshaftFM 2 жыл бұрын

Not really sure mate could have been incorrect fitment Or the bushings could have been poor quality

@mgbs5824 Жыл бұрын

What are the red bushing benefits versus original bushing?

@CamshaftFM Жыл бұрын

I personally think the blue super pro ones aren’t as good quality as the nolothane ones

@jakeholmsen1842 2 жыл бұрын

Hey brother where did you get bushings?

@CamshaftFM 2 жыл бұрын

The Nolathane website

@oldtoyotas 3 жыл бұрын

Were the old rear bushings rubber or poly? If rubber, which do you prefer? I'm leaning towards an OEM rubber type because I don't want extra noise/vibration on my FJ62.

@CamshaftFM 3 жыл бұрын

It would have originally had rubber but they were poly ones and I put poly ones in. I’d use poly ones they last longer and the noise and vibration difference would be so small you wouldn’t be able to tell the difference

@oldtoyotas 3 жыл бұрын

Ok, thanks for the input. My only experience with a poly bushing was a poly motor mount in my old FWD car which only lasted about a week, too much feedback. It makes sense there would be much less in the leafs.