How To replace a T25/T3 bus Front wheel bearing.

Рет қаралды 13,284

4 жыл бұрын

Doing a bit more to the bus.
See our KZfaq channel at:-
/ @larcsworkshop
Join us on Instagram at:-
/ larcs_workshop
I have to warn you that I have no formal automotive training, and have just learned by breaking stuff. If you can learn anything from my mistakes then great, but you do so at your own risk!

Пікірлер: 36

@gdecoteau9382 2 ай бұрын

great content, thank you! i've wanted a bus since i was 13 years old and just bought a 79. i appreciate the effort and instructions. :)

@LarcsWorkshop 2 ай бұрын

Thanks, no problems. I hope you enjoy your bus👍.

@peterarvaszulu5069 3 жыл бұрын

Liked watching this presentation, you are polite and your language is clean.

@LarcsWorkshop 3 жыл бұрын

Thanks, that's much appreciated 😃. Cheers Larcs 👍

@jamesworgan1559 2 жыл бұрын

First class video, Clear and precise!

@LarcsWorkshop 2 жыл бұрын

Thanks 👍

@lukebohemian Жыл бұрын

Great help. Will be changing ours this afternoon 😅

@LarcsWorkshop Жыл бұрын

Thanks, good luck sorting it out 🤞. Cheers Larcs 👍

@steamyrotter 4 жыл бұрын

Totally transferable to other makes too Keep it up. 👍👍

@LarcsWorkshop 3 жыл бұрын

Cheers, Larcs.

@danieldooling6756 4 жыл бұрын

Absolutely brilliant video, really really thorough. Do I get the bus out the barn and have a go at these or get the garage to do it? Have a go I rekon! Cheers

@LarcsWorkshop 4 жыл бұрын

Thanks for your comment. Absolutely, drag it out and get your hands greasy 😃👍

@gavinwilson3951 3 жыл бұрын

Good video

@LarcsWorkshop 3 жыл бұрын

Thanks for the kind comment Gavin. Cheers, Larcs.

@markspragg1359 4 жыл бұрын

Any chance of some videos of the Buell? Keep up the good work, enjoy your vids.

@LarcsWorkshop 4 жыл бұрын

Thanks very much Mark, you've got a keen eye. I'll try and do a walk around of the Buell some time :0)

@michaelell8124 Жыл бұрын

Hi Larcs, great video, inspired is to have a go at replacing off side front bearings, but we can't get the caliper bolts out...any tips etc...

@LarcsWorkshop Жыл бұрын

Thanks, all I can suggest is to turn the wheel to give you good access, use some easing oil, use a six point socket and breaker bar and give it all you've got. Sometimes a bit of heat will help. Good luck sorting it out 🤞. Cheers Larcs 👍

@louisvanrijn3964 4 жыл бұрын

A 100% correct video. The (stiff) sliding of the washer indicates the right applied torque on the nut. Apply the right (SKF) wheel bearing grease, but not to much. Keep everything very clean! Not 1 particle is allowed here. Checking the torque in practice: It is very informative to lift the wheelcaps after after a sufficient long drive (say 30-50 miles) and feel the temperature of the bearing on the black cap. A well torqued bearing is luke warm, that is the normal temperature. Louis van Rijn. 405.000 km in a 1980 T3

@LarcsWorkshop 3 жыл бұрын

Cheers

@earlyreefer 2 ай бұрын

Sorry, bit confused, but doesn’t the hub nut get torqued vs just wee past finger tight? The one holding the anti rotation washer.

@LarcsWorkshop 2 ай бұрын

Probably, you would need a crows foot adapter for the torque wrench though. I haven't got any so did it the old fashioned way 😁

@DanTheManIOM 4 жыл бұрын

Great Video. This is what is on my 85. If I have a lot more drag when I spin the hub, could it be too much grease ? I definitely used more. THen, I tightened it down tight and backed off, but it has a lot more drag...but washer moves...I'll go back and check it while it still sitting on the jackstands.

@LarcsWorkshop 4 жыл бұрын

Thanks for the feedback. More grease might be a bit 'draggy' especially if it's really cold. I would whip it off again and check everything is OK just in case though. If the seal isn't fully home or not quite straight it will cause it to drag. Check the bearing races are in straight too, but this is more likely to cause a 'loose then tight' sot of feeling. Good luck

@DanTheManIOM 4 жыл бұрын

@@LarcsWorkshop thanks, seal was not even, races were in there tight, checked just to be 100%, but it was the dust shield..the originals were rusted away, and the new ones were not identical, I bent them back and everything works now...I used a mercedes spindle nut ....Thanks !

@stevelarcombe4817 4 жыл бұрын

@@DanTheManIOM Brilliant, glad you sorted it out.

@tomchloe3208 10 ай бұрын

I have just changed mine, but for some reason the disc is now sitting way too close to the heat shield, what have i done wrong? Its throwing loads of smoke out, and now locked the wheel

@LarcsWorkshop 10 ай бұрын

Have you definitely put the outside race of the inner bearing into the back of the disc? I had the same issue years ago and realised that I had forgotten to fit it and just put it all back together. Easily done.