You are a good teacher of trade lost years ago bless you Sir.
@KITS_Auto_and_Truck_Repair10 ай бұрын
@chrishastedt9597 Thank you!
@petermartinez55733 жыл бұрын
Great video. You explained everything systematically and thoroughly. Good job my man. The only other thing you might have discussed is removing the protective coating from the new rotor. Much respect.
@KITS_Auto_and_Truck_Repair3 жыл бұрын
Peter Martinez thank you!!!
@rzigmont Жыл бұрын
Great video! The bearing doesn't come off the hub assembly quite as easy as shown. Usually takes a great amount of pounding and prying, but we get how to complete the project. Thank you
@KITS_Auto_and_Truck_Repair Жыл бұрын
Robert Zigmont My Pleasure!!
@chrishastedt959710 ай бұрын
Depends on the climate you live in.
@waynedickens4031 Жыл бұрын
Great video . I like your little asking what's next . Gets people involved. Nice . Enjoyed the video
@KITS_Auto_and_Truck_Repair Жыл бұрын
wayne dickens Thank you!!
@jermelljackson19623 жыл бұрын
This was a great video. You explained things very clear. My only question is that why have you not removed the tire rod bolt? I Saw a similar video where they removed the tires rod bolt.
@KITS_Auto_and_Truck_Repair3 жыл бұрын
Jermell Jackson thank you, I didn't remove the tie rod because I had enough room to remove the bearing... and the steering wheel was unlocked, so I could turn the steering knuckle without any problems...
@andrewmacauley36652 жыл бұрын
Awesome video! Thank you so much for the indepth explanation and good pace Through out the video. It really helped me do this to my car! Thank you!
@KITS_Auto_and_Truck_Repair2 жыл бұрын
Andrew Macauley My Pleasure, I'm glad to hear that the video was helpful!!!
@eclipse1999able3 жыл бұрын
Awesome bout to do this on a friend's car. Thanks
@KITS_Auto_and_Truck_Repair3 жыл бұрын
kyle o My Pleasure!!!
@rgvcateye90588 ай бұрын
Awesome video! What are the torque specs for the 3 bolts of the hub and the center nut?
@KITS_Auto_and_Truck_Repair8 ай бұрын
@rgvcateye9058 Thanks! the torque spec for the bearing bolts is 74 lb ft and the drive axle bolt torque spec is 111 ld ft for the first time then loosen the nut 45 degrees then tighten it to 184 lb ft
@steveburns9684 Жыл бұрын
Great video..just one thing..What about pumping the brakes Back up when your done?
@KITS_Auto_and_Truck_Repair Жыл бұрын
steve burns Thanks! and yeah the brakes have to be pumped up at the end, thanks for pointing that out!!
@wellingtonmiller16223 жыл бұрын
Great job .
@KITS_Auto_and_Truck_Repair3 жыл бұрын
wellington Miller Thank you
@jl-heatfan4life7172 жыл бұрын
Ur explanation is on point 👍 but dont u disconnect the ABS Line Harness? Had a malibu with Hub Assembly that had ABS Line connector attach to it n it pinches the wire so i guess newer models is not attached ABS Line with Hub Assembly huh? Thank u bro
@KITS_Auto_and_Truck_Repair2 жыл бұрын
J6IX LARRY21 My Pleasure!! Thanks
@elijahyousif59529 ай бұрын
Hello, can you please tell me where did you get the front wheel bearing hub assembly from ?
@KITS_Auto_and_Truck_Repair9 ай бұрын
@elijahyousif5952 I got it from my local parts store!
@mrburgess67772 жыл бұрын
Will this procedure fix the traction control/abs light indicator showing on my dash??? I can save lots of money doing this myself... Thanks for the video 👍
@KITS_Auto_and_Truck_Repair2 жыл бұрын
Mr burgess if your problem is the abs sensor or the wheel bearing this procedure will help you fix it!!
@waltherherrera67 Жыл бұрын
Excelente 🎉🎉🎉👍👍👏👏
@KITS_Auto_and_Truck_Repair Жыл бұрын
Walther Herrera Thank you!
@Juclo902 жыл бұрын
It’s necessary to putting back the rotors splash plate? Because the new rotors I bought is bigger than the factory I find in the car. It doesn’t fit in the splash plate. If I put it back without splash plate it’s fit but, but with splash plate it doesn’t. So I have to keep the splash or it doesn’t matter to keep it or not? Can you answer to me please. Thanks you
@KITS_Auto_and_Truck_Repair2 жыл бұрын
Clauzel Etoyla you need the splash plate, you should get the right rotor!
@Juclo902 жыл бұрын
@@KITS_Auto_and_Truck_Repair thanks you
@KITS_Auto_and_Truck_Repair2 жыл бұрын
@@Juclo90 My Pleasure!!
@elijahyousif59529 ай бұрын
What is the size of the axel nut ?
@KITS_Auto_and_Truck_Repair9 ай бұрын
@elijahyousif5952 I believe it was a 32mm
@elijahyousif59529 ай бұрын
THANK YOU BROTHER SO MUCH AND YOUR VIDEO IS A TREMONDOUS HELP GOD BLESS YOU@@KITS_Auto_and_Truck_Repair
@KITS_Auto_and_Truck_Repair9 ай бұрын
@@elijahyousif5952 My Pleasure!
@bowfeeznuts39122 жыл бұрын
What do I have to order an essembly or a hub
@KITS_Auto_and_Truck_Repair2 жыл бұрын
BOWFEEZ NUTS yeah it's basically the same thing, you can say hub or hub assembly
@bowfeeznuts39122 жыл бұрын
@@KITS_Auto_and_Truck_Repair and for a 2016 limited front is it different from 2015
@KITS_Auto_and_Truck_Repair2 жыл бұрын
@@bowfeeznuts3912 it's the same process
@PaPabearj1Ай бұрын
Once I replace the Oxygen Sensor (upper), the engine began to die.
@KITS_Auto_and_Truck_RepairАй бұрын
@PaPabearj1 did you install an aftermarket sensor in it?