It's a very simple task every homeowner should know how to do. Change an outlet.
Пікірлер: 145
@clintontheross Жыл бұрын
It’s easier to take the hot off first and cap it off. Then you can touch the plug anywhere no risk. Take the other 2 wires off and then reverse order for the new plug. Put on hot last
@BigChill2283 ай бұрын
Good tip.
@r12rtpilot3 ай бұрын
Thanks changing a dead outlet tomorrow . I’ll remember your advice!
@clintontheross2 ай бұрын
@@r12rtpilot I hope it worked out and no shocks were had! lol
@mizlola68 Жыл бұрын
Total game-changer! I can do myself now! I wish I could have been shown this years ago. Oh well... It's never too late to learn something new. Thank you!
@michaelp9238 Жыл бұрын
Please don't do this without turning the power off. Even if you've got a decade of experience it's still very dangerous and a misstep could result in hospitalization or death.
@Super0Troll0Lee Жыл бұрын
@Michael P Normally just wakes you up. But yeah. Not advisable. And if someone tells you it's off.... use a tester to be sure.
@user-jw5du3gb7e6 ай бұрын
Thank you for the voice of reason. The man in this video could be dead, just sickening to watch. And the comment below says it will just wake you up. I've seen a man fly across the room backwards in electronics class. They were awake before they made this type 0f boo boo. Luckily they even woke up again after having their head slammed into the wall. Don't trust these videos. Dead lasts a very long time. Learn how to correctly turn your home's power supply off. And you probably shouldn't just watch another video here about how to safely turn off the power supply so it doesn't come back on while you are working! I'm not telling you how. My stomach can't watch another video here on how to shut your home's power supply off.
@FreeAmerican-mm2my Жыл бұрын
This is clearly fake. Code requires that real electricians curse a minimum of two (2) times when performing an outlet replacement. It is Code to curse twice when removing the outlet, twice when replacing the outlet, or once when removing and once when replacing. If there are more than five curse words during the procedure, Code requires that the work be performed by a master electrician with 20+ years experience or service in the U.S. Navy.
@michaelcolella57382 жыл бұрын
You can also wear low voltage electrical gloves which fit comfortably.
@elc2k385 Жыл бұрын
When he goes to put back on the black wire, his needle nose gripping hand is getting dangerously close to the metal of the pliers, and since hes holding the grounded yoke with his left hand, he risked sending a little shock through his heart.
@JacquelinePavan Жыл бұрын
Thank you for the tutorial!
@speeder366 ай бұрын
You don't realize how dangerous this is!
@Ojeramup12Ай бұрын
Thanks for the video! I have always wondered how to do this.
@pkaspar784 ай бұрын
I hope that at least half of the people in this comment section is still alive
@raygunsforronnie8475 күн бұрын
I'm hoping that all the people who found this to be a green light to work on energized equipment are still alive and that buildings didn't catch fire.
@AlSabado-at-alsabado-com2 жыл бұрын
Thanks so much for teaching how to do this safely when not shutting off the main power source. :)
@Thebige33752 жыл бұрын
You're very welcome. Thanks for watching!
@garyking63652 жыл бұрын
At 3:54- 3:59 the hot wire where it is spliced white to black has a bare-wire spot and that along with your pliers came soooo close to touching the hot wire it isn't even funny. You also had your fingers touching the metal on the pliers (off the rubber handles). Don't try this, get the power off unless you really know what you are doing. Wire colors are different sometimes. Or get a real electrician to do it. Or for a temporary fic simply pinch the plug prongs together or pull them apart a little. This will mechanically hold the plug in the wall.
@kennethpayne62102 жыл бұрын
What a idiot, please people Do Not Do This !!
@howdybrothers7727 Жыл бұрын
@@garyking6365 this is probably a dumb question but what happens if they touch? an explosion or something? i know very little about stuff like this
@howdybrothers7727 Жыл бұрын
@@garyking6365 and just to add i have no intention of trying this, i randomly stumbled across this video and your comment made me curious
@CS-bh4ur2 жыл бұрын
I would just add one thing. If you’re a nice electrician or handyman you should wrap the finished new socket with electrical tape. That way when you change it in the future you don’t have to be careful to only touch those two spots that he was touching in the beginning
@BrownEyePinch2 жыл бұрын
Tape costs money
@FreeAmerican-mm2my Жыл бұрын
Especially if a metal box.
@tempviduseАй бұрын
I always tape them. Especially in a metal box
@dixonwong68742 жыл бұрын
Wow you are brave I am to scare. I will turn off the power first and then do the work more safe.
@helmutc.vanyumcookie81972 жыл бұрын
Just because you CAN, doesn't mean SHOULD. : (
@BSheaffer76Ай бұрын
If you absolutely have to change a live outlet, I would strongly recommend spending the $20 on an insulated screwdriver. Also as someone else suggested, cap the live wire first and reattach last.
@jadyngasaway89393 жыл бұрын
I really needed this help thank you so much- I need mine changed and I have for years but when I ask my dad it’s always “We’ll do it another day” and so I didn’t know how to do it myself thank you so much
@Thebige33753 жыл бұрын
You are very welcome! I'm glad I was able to help.
@lamalfullington3278 Жыл бұрын
Thank you both, now I feel more confident working around live wire's
@zakkwylde4201 Жыл бұрын
I love these comments on here lol thanks for the simple tutorial. There are a bunch of reasons why you gotta do it this way sometimes
@rorysalarms81104 ай бұрын
Erik Stueckrad When i do a outlet or light switch hot i Usually take the ground wire off then the neutral. wire then the hot wire and i also use a orange 1000v Klein insulated screw driver so i don't cause a short.
@martinguajardo17552 жыл бұрын
I've seen a electrician at a local hospital change a light switch with power on 👍⚡⚡
@JAGteam2 жыл бұрын
Thank you!! Been asking my husband to do this for 6 months! Time to do it myself! 😅
@BrownEyePinch2 жыл бұрын
I wouldn't do it either
@DTLA276 ай бұрын
Your husband is a smart man lol
@kaykiekid4 ай бұрын
Many, many, many, thanks! I'm going to change 2 problematic outlets! 😑 Safely, of course! ☺️
@outlander51512 жыл бұрын
Wear rubber gloves and tape wires and metal parts with electrical tape as you work and you should be fine. If you are not doing this professionally take your time!
@Chris.Rhodes2 жыл бұрын
I always wondered, after taking off about 1000 plate covers every month, why in the hell do they use flat screws!? Why not phillips? Or anything OTHER that flat!? It annoys the piss out of me! Thanks for the video! And also, to add to the video, when working with tools, always remember that the tools are metal, so ALWAYS keep your hands on the rubber. Good video for showing how to do it, but from the looks of how you're touching the pliers, you had your finger resting on the metal part of the pliers when touching the hot wire, which tells me that's a dead outlet or you're superman! 🤣
@aaronweiser54212 жыл бұрын
Make sure you shut of the power supply, I tried doing this way and 2 wires crossed and blew my breaker and nearly Electrocuted me.
@Chris.Rhodes2 жыл бұрын
@@aaronweiser5421 yup I've done it. I also did it to where my fingers were on the shaft of the screwdriver and grounded myself out tightening the hot screw, that felt like hell lol
@ktpowerwashing Жыл бұрын
Spends more time trying to keep the wires from touching (which they do) vs. walking a few steps to flip the breaker off. C'mon Really?!
@Chris.Rhodes Жыл бұрын
@@ktpowerwashing right lol
@Allan-il6mh6 ай бұрын
@@ktpowerwashingwhat if I don't know what breaker is which?
@tryssulli9 ай бұрын
I did something like this in my apartment before, I broke my light switch and couldn’t locate a breaker to cut power. I basically did what you did and also wore some thick ass rubber gloves 🤣
@Karen-ib4jc2 жыл бұрын
Thank you for making this so simple even a senior could understand.
@mjvlovescbv2 жыл бұрын
I've changed live outlets plenty of times. Just don't touch the power/neutral at the same time but if you do on accident, 110 is just a little shock
@queze0092 жыл бұрын
savage lol
@FreeAmerican-mm2my Жыл бұрын
Chihuahua's only give you a little bite too.
@jamesborton923710 ай бұрын
110 volts is indeed just a little shot. It did give my pace-maker just a little jolt . Then I just performed just a little break dancing...
@outlander51512 жыл бұрын
Sometimes people do not have access to the main junction box or circuit breakers!
@raygunsforronnie8475 күн бұрын
Access to a means of disconnect is a Code requirement.
@kevreilly7 Жыл бұрын
How do you know for SURE whether to buy a 10, 15, or 20amp outlet??
@peterchan74282 жыл бұрын
It’s too dangers working with the power on, why don’t just shut off the power, you’ll live only once! Never take chance!
@darrellfox41172 жыл бұрын
This is a VERY BAD IDEA do not do this if you have any way to shut off the breaker. It is not worth the chance of the many things that could go wrong. You don't have to be a licensed electrician to change an outlet but doing it with a live circuit can be life threateningly dangerous.
@BrownEyePinch2 жыл бұрын
Men
@johnathanwoods1223 Жыл бұрын
Oh yeah. Definitely should've shut off the breaker box.
@playboicarlos Жыл бұрын
In my job I was gawed at by my peers for suggesting this. They looked at me like a pussy.
@Twelvegoldteeth Жыл бұрын
Relax man. I do it all the time. You just have to know what you’re doing. The trip to a breaker box sometimes isn’t worth it…
@bquick111 Жыл бұрын
@@Twelvegoldteetha year later, you still alive and switching out live receptacles?
@xr7604 Жыл бұрын
I’m changing one now, couldn’t get the right breaker switch for it. (Literally hit all switches and it turned off all plugs around it Old home I guess idk- maybe I missed it). Anyway, I need to change the box too. Should we use a steel one or plastic? Also, can I cap off the end of the wires while removing the box? Thanks!
@FreeAmerican-mm2my Жыл бұрын
I am sure you are done, but I would us a plastic box and I would at least tape/wirenut the black line.
@mustangelite15 күн бұрын
Curious why 2 screws on each side if you only utilize 1 screw per side?
@Rjey45ForteFev Жыл бұрын
i have a question. Why our outlets always keeps shutting down with TV is try to turn on?
@POLOAZTECA Жыл бұрын
Simple enough with 3 wires... A lil trickier and scarier when You got 5 wires meaning a middle plug which will have 1 ground, 2 neutrals and 2 hots!
@FreeAmerican-mm2my Жыл бұрын
Only one of the hots is hot. That it the wire that gets the most attention.
@kevreilly7 Жыл бұрын
Just find the breaker,,,smh
@ryanthompson3446 Жыл бұрын
Take the hot off first.
@AquaTech2252 ай бұрын
I do it to or do work on a bunch of hot things. But I do do it with insulated tools an alota times some 9-10mil nitrile gloves on to just for added protection. Because all it takes is to bump into or brush up on the wrong one. Sometimes going to the breaker just isn’t worth the extra steps. But I would say for the regular homeowner. Not messing with electrical daily. A used to messing with it in general a not completely sure of what there doing. Test it with a meter or at the least a non contact. Turn ya breaker off an check again an verify it. No sense to chance it. An if ya really unfamiliar hire someone that can. Otherwise it can be done. But ild never advise someone to do it. Edit: also if your home is old or someone added their own addition a what not. Electricity dont know color. So what you think something may be in certain situations it may not be. An that’s when knowing an understanding of what your looking at is needed.
@rob57632 ай бұрын
There are some cases where a pro has to work hot but will always kill power if possible. A homeowner should never work hot. There is no reason to not turn breaker off. Also, as stated below, it is safer to remove the hot first and reattach last.
@renealvarado36588 ай бұрын
Please just turn off the breaker 😮😅 be safe everyone 🎉🎉🎉
@alanagnew3451 Жыл бұрын
Why would you take the neutral off first?
@joecummings12603 ай бұрын
As an industrial guy I've been in situations where I worked hot to avoid shutting down production, but anymore it's a big no no if you get caught doing it. But for a residential receptacle, why work hot?
@A87CEO Жыл бұрын
Just an observation. If the plug is hot, why are you touching the non-insulated part of the long nose pliers?
@WESTCOAST253 Жыл бұрын
Touching the non insulated part of the tools CAN keep you insulated or isolated from the current. (There are insulation ratings) But you should be good as long as your not grounded. You will feel it if your body creates a path for current. Touching non insulated parts keeps that path open and safe
@cypher6862 жыл бұрын
your hand touched the metal of the pliers so many times. So I feel that this is probably fake
@Thebige33752 жыл бұрын
No, not fake at all. On the negative side( or ground) you will not get jolted at all. On the positive side you will not get shocked if you only make isolated contact. Electricity needs both a hot and a ground in order to flow.
@Hellvor2 жыл бұрын
You would need to be connecting both the neutral and hot contacts in order to produce that shock.
@garyking63652 жыл бұрын
@@Thebige3375 Your tool touched both wires you are lucky you didn't get shocked. Horrible video to be showing people.
@zakkwylde4201 Жыл бұрын
@@garyking6365 ...that's not true. I aught to report you to the information police 🚔 misinformation in the first degree
@raygunsforronnie8475 күн бұрын
@@Thebige3375 That presumes that all wiring connected to that circuit, or that panel, are free of defects and mistakes.
@minnesotajack1 Жыл бұрын
If I ever find myself in a situation where I have to change a live outlet, I’m calling an electrician. To me this is like do-it-yourself surgery.
@kevreilly7 Жыл бұрын
Waste of $150
@justSomeUserOnYT Жыл бұрын
@@kevreilly7 lol I mean if you have $150 spare and want to guarantee you won't kill yourself, it is worth it.
@joshmmi23 Жыл бұрын
As an electrician I would definitely be safe and just cut the power..not worth the risk..never worth it
@drunkenirishmstr2 жыл бұрын
I’m going to try this, normally I would just flip the breaker and go to work but because I don’t have access to the breaker and my landlord won’t send an electrician I have to do it this way. Would insulated tools work doing this?
@Thebige33752 жыл бұрын
Hey Donald, yes you should use insulated tools. You can go overboard and wear rubber gloves if you want. Just pretend like your playing operation and you should be fine. Don't forget to look at the little piece of metal connecting the 2 screws on each side...if it is in one piece then you should only have 1 hot wire. If it is snapped and separated then you most likely have 2 hot wires. 1 would be constant and 1 operated by a light switch.
@TrinitySurvivorNet2 жыл бұрын
NEVER try to change a live outlet! If you touch a live wire with your tool and any part of the metal of that tool, you are FRIED! BAD IDEA...Judt get a flashlight and cut the power off! Stay SAFE!
@Mr.S_BuildsThings2 жыл бұрын
When I was a kid I would stick flat heads into the outlet. Sure it made a bang and the power would go out but I didn't get hurt (by the outlet), dad always let me learn the hard way though
@chichithebullterriershepsk12902 жыл бұрын
Sometimes you have to dummy
@buffalojoe7052 жыл бұрын
what if your working in a nursing home where people are on oxygen, so you literally can’t turn off the power. Happens all the time, shiiiiitttt even with apprentices.
@DoubleTopHoneyCo2 жыл бұрын
Thanks to Nikola Tesla, you don't get fried, but shocked. Don't do this with Thomas Edison's "will kill ya" 220-240v. Besides, it's the amps that will kill you.
@erikkarling2176 Жыл бұрын
That's not true! Not at all. It's when you put yourself in between the difference of potential. You can touch a live wire without any problems whatsoever. It's when you grab a hot and neutral wire at the same time with different hands, then you create the path of electrical flow within yourself.
@larryleisuresuit95842 жыл бұрын
Adult version of operation. LOL I mean, if the outlet is actually live.
@simplytrolling68692 жыл бұрын
Looks to me like those needle nose have been used as a voltage detector… just saying 🤷♂️
@mrmaddocs68752 Жыл бұрын
To prevent electrical shock, I will turn off the power
@acesandeights6510 күн бұрын
Make sure your standing in a bucket of water.😂
@narutodertrautista24282 жыл бұрын
just did this and uh yeah didn’t end up well, it exploded right into my face and my father asked what happened and I got out of my room clueless, now it’s hanging and can’t touch it until the house is alone LOL don’t want my father finding out
@BrownEyePinch2 жыл бұрын
And while wearing a metal ring🙄
@rhysdickson17802 жыл бұрын
Are you kidding me, this is a real life horror movie. Why teach people to take such a STUPID risk. This could kill someone, especially if there was no safety switch in the power box. This video should be taken down. Stick to your day job Erik
@SDG702 ай бұрын
Clearly took too long to change an outlet. This guy must get paid by the hour😢
@horacesoward9638 ай бұрын
Great video if you're trying to get someone killed. It would have been much better if you had explained what not to do or touched.
@luisaguilar65202 жыл бұрын
BAD ADVICE!!! If you're not an electrician, ALWAYS turn the power off. It's too easy to cause a flash or worse!!!
@FueMalacai Жыл бұрын
Believe in what you want but there is a spark when connecting any hot to someth5thats grounded. So this video isn't real. The power is off where he is
@143Garage2 жыл бұрын
Yea nah lol. They have 25 dollar tools that help you locate the exact breaker to shut off for beginners. Just do it the right way
@2ASPARKY2 жыл бұрын
a vacuum works great
@blue_hedgehog_gaming_clock95802 жыл бұрын
What is you don’t have access to the breaker
@Barker-sf5zw6 ай бұрын
I love the fat bastard breathing going on while you work. Makes me feel like I’m with my people.❤
@shubert5956 Жыл бұрын
man all you gotta do is cut the lines close to the receptacle starting with the hot an re strip
@mirsadmemic5863 Жыл бұрын
He nose is swelling from adrenalin
@separateemail99742 жыл бұрын
NOT A GOOD IDEA AT ALL ! ALL YOU HAVE TO DO IS SLIP WITH YOUR SCREWDRIVER AND OR PLIERS AND YOU RISK A SHORT CIRCUIT OR A SHOCK ! THIS IS A BAD VIDEO THAT ONLY AN AMATEUR WOULD ATTEMPT TO DO ! don't try this !
@garyking63652 жыл бұрын
At 3:54- 3:59 the hot wire where it is spliced white to black has a bare-wire spot and that along with your pliers came soooo close to touching the hot wire it isn't even funny. You also had your fingers touching the metal on the pliers (off the rubber handles). Also those wires have many pinched insulation spots on them exposing the bare wire. Very dangerous! I see you pinch the insulation when you are taking the wires off. Why would you do that? You are making it more dangerous. Also at 5:01 your screwdriver came so close to shorting between those wires. Please tell me you are not an electrician? OMG please take this video down. You are reckless with your work and lucky or the power was off to begin with. I'm going to report this video as dangerous
@larryleisuresuit95842 жыл бұрын
I have looked a few times, I wanted to see if anyone caught that and scrolled down to this. LOL I don't think it was close, look again, it should have thrown sparks, he never showed that outlet was live. I have done this successfully and also unsuccessfully ( I mean, I completed it but got shocked ) in my life time but it's always a crap shoot, every time. I don't believe this outlet was live though.
@JulianA-tr6pt Жыл бұрын
@@larryleisuresuit9584 I don't think he actually shorted across them, even if it wasn't live. The camera likely makes it seem closer than it was. The wires are all connected, so they're vibrating together. It's really not hard to work live, or much of an accomplishment to do so without being shocked or shorting something. Just completely unnecessary 99% of the time. It is exciting, no doubt.
@alexsotelo7176 Жыл бұрын
What I am wondering is how his pliers didn’t spark in the beginning when he was disconnecting the neutral by prying from the bare copper? Someone please explain I just started electrical school
@jjanderson8235 Жыл бұрын
Patently DANGEROUS! Why would anyone change a receptacle with a live wire??? ... It takes less than 1A to kill! How many Amps is that outlet? SHUT OFF the breaker, buy a cheap tester at least, be safe.
@KarterHartzheim-go8fx9 ай бұрын
That is so unsafe
@richardgray45Ай бұрын
Absolutely ridiculous. This encourages people to take on tasks that could kill them. Always isolate the supply. Being in the UK which is really anal about electrical safety and had probably the best safety arrangements for Electricity not to mention a higher voltage, all circuits have an MCB to make that job entirely safe. So stay safe my American cousins and ignore this.
@user-jw5du3gb7e6 ай бұрын
The man in this video could be dead, just sickening to watch. And the comment below says it will just wake you up. I've seen a man fly across the room backwards in electronics class. They were awake before they made this type 0f boo boo. Luckily they even woke up again after having their head slammed into the wall. Don't trust these videos. Dead lasts a very long time. Learn how to correctly turn your home's power supply off. And you probably shouldn't just watch another video here about how to safely turn off the power supply so it doesn't come back on while you are working! I'm not telling you how. My stomach can't watch another video here on how to shut your home's power supply off.
@darkknightXII Жыл бұрын
In this video.. THE HOT WIRE ISNT LIVE. YOU CAN SEE HOW MANY MISTAKES HE MADE
@zakkwylde4201 Жыл бұрын
..you can? He didn't touch the neutral and the hot wire at the same though, that's basically the main idea...
@boxermata58942 жыл бұрын
Wow who is this guy ...big safety hazzerd & bad teaching !