How to Replace Engine Oil Pan 92-01 Toyota Camry

Рет қаралды 186,440

1A Auto: Repair Tips & Secrets Only Mechanics Know

7 жыл бұрын

Buy Now!
New Engine Oil Pan from 1AAuto.com 1aau.to/ia/1AEOP00057
BUY THE PART:
CLICK "SHOW MORE" TO SEE INSTRUCTIONS BELOW:
In the video, 1A Auto shows how to, remove, install, replace, or change a broken, worn, loose, or leaking oil pan. The video is applicable to the 92, 93, 94, 95, 96, 97, 98, 99, 00, 01 Toyota Camry
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oagn/1AXAA00013
• 10mm Wrench 1aau.to/opi/1AXAA00010
• 12mm Wrench 1aau.to/opi/1AXAA00010
• 14mm Wrench 1aau.to/opi/1AXAA00010
• 10mm Socket 1aau.to/oUX/1AXAA00017
• 12mm Socket 1aau.to/o3I/1AXAA00015
• 14mm Socket 1aau.to/o3I/1AXAA00015
• Oil Filter Wrench 1aau.to/oaa/1AXAA00026
• 3/8 Inch Breaker Bar
• Ratchet 1aau.to/oahT/1AXAA00016
• Socket Extensions 1aau.to/o3I/1AXAA00015
• Torque Wrench 1aau.to/ouV/1AXAA00044
• Brake Parts Cleaner
• Bungee Cord
• Engine Oil
• Gasket Adhesive
• Gloves 1aau.to/odK/1AXSS00048
• Paper Towels 1aau.to/ohk/1AXSS00035
• Rust Penetrant
• Drain Pan 1aau.to/ogL/1AXAA00320
• Floor Jack 1aau.to/otc/1AXAA00068
• Funnel 1aau.to/ocV/1AXAA00310
• Jack Stands 1aau.to/otq/1AXAA00065
• Rubber Mallet 1aau.to/oas/1AXAA00413
• Wire Brush 1aau.to/oeo/1AXAA00079
For More Info visit us at 1aau.to/h/bc9/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 111

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@oharac4178 2 жыл бұрын

First thank you for the video. i must correct 1 thing. Once you get the exaust brackets off and u have just insulation left instead of ripping it out. Just take dust shield dow and tug gently on insulation at the same time and it will comeout in one piece.

@1AAuto 2 жыл бұрын

+oharac4178 Thanks for the feedback!

@quintaylor4330 Жыл бұрын

you guys literally make the best "how to" car videos on KZfaq. this would've been a shaky, 2 hour, unedited video off some dudes phone.

@rickamador719 7 жыл бұрын

took me forever to find a video with someone who actually knows what they are talking about great job dude

@jeeyuantan7711 3 жыл бұрын

these guys are legends for doing this

@brandonowens8807 2 жыл бұрын

Seriously. I have the 98 Celica, and NO ONE has a video on any maintenance. Thankfully these cars share the same engine.

@berrywin 11 ай бұрын

Best video so far concerning removing and mounting the oil pan on a 5SFE engine! Clear and thorough instructions!

@thegee-tahguy4877 2 жыл бұрын

I can't stress enough how having a lift makes this whole job HUGELY easier and MUCH faster. Working on your back in your driveway makes everything you have to reach up into a total pain for those old enough to drive one of these die-hards, especially if you're on gravel or in a tight garage. A lift affects what tools you use from extensions to lighting. It's fine if you do have a real lift, but with jack stands it's almost unfair to make people think it's nearly as easy as this video shows. I honestly do appreciate this video showing the steps, really, but I think it needs to be said you will be under your Camry all day , if not into the wee hours if you think this job can be done by most DIYers in an hour or 3, not to mention when/if the head pipe studs break, like 2 of mine did. How's about talking about contingencies when bolts starts snappin' off or one is stripped on your 207 year old Toyodal Clamry 2.2l?

@EricVonHunter 2 жыл бұрын

Truth! I'm doing this right now on ramps.

@GF-mf7ml Жыл бұрын

I just diy a old 80s Mitsubishi, it's very hard.

@MrSparkymike1 4 жыл бұрын

Denatured Alcohol works great at removing silicone gasket material from metal surfaces. Use it along with a copper dish scrubber, wear gloves or the alcohol will remove all the moisture from your hands and your fingernails will split at the cuticles.

@dbfcrell8300 2 жыл бұрын

There is a gasket for the 97-01 Camry 2.2l. I'm in the process of fixing a RTV gasket leak someone did b/c they didn't use the gasket or leave the sealer in a bead, so you may want to consider either buying a good gasket instead of making one out of sealer or leaving the sealer in a bead. Felpro makes a decent rubberized gasket that doesn't require sealer and is made for imperfect mating surfaces. This is still a great video that shows the whole job head to tail, so I thank you for posting it.

@phantomgaming8137 2 жыл бұрын

I'm in the process of doing this as well, I have the gasket but I'm debating just using rtv after watching the video and reading in forums about just using rtv. Except instead of spreading it I'm going to leave it in a bead

@davenstewart3239 Жыл бұрын

@Phantom Gaming Did you end up using it in a bead form? I thought about getting the gasket, but I have black RTV lying around. How did this turn out for you?

@simonsw9410 2 ай бұрын

I just tried to tighten those bolts, as many as i can reach. It worked, no more leak. 2001 Camry se

@dansap100 4 жыл бұрын

I was getting different input after search, but I'm glad I found your video. It's very detailed and very clear. Thank you very much.

@chrisr.986 Жыл бұрын

Did you change the gasket if so any pointers. The gasket is in my to do list. I'm worried the bolts might break.

@Anthony_in_Bloomington_Indiana 4 жыл бұрын

You have to drop the exhaust pipe just to reach a few bolts on the oil pan! That is an insane design! . I have a 2004 Toyota Corolla, and I'm learning how to change my oil pan gasket, before I do it for real. I am suddenly relieved that I have a Corolla and not a Camry. . And my Corolla oil pan has an actual gasket, which is much easier than dealing with gasket sealer. I bought one for cheap on Ebay Motors.

@pablogon98 2 жыл бұрын

Same here! Seems like a hassle having to remove so many parts of the exhaust only to replace the oil pan. And the gasket part too!, remember to line it up properly and torque the bolts in a criss cross pattern ;)

@glenglene8473 2 жыл бұрын

To change the oi pan gasket in the E90 BMW 335i would cost you $2,000. You have to drop the subframe and everything else to get to it.

@phantomgaming8137 2 жыл бұрын

The camrys have a cork gasket, so far its better just to do a rtv

@zacinnc78 Жыл бұрын

man u have the best camry guides out there bar none !thx to u im keeping my gfs old camry going ! Also that AT had alot of oil on it too u reckon u had a leaking valve cover gasket?(especially on the backside which is hard to see)

@rickamador719 7 жыл бұрын

do you guys have a video on replacing timing chain gasket, I just replaced my oil pan and gasket on my 97 toyota camry le 2.2l thanks to you guys , come to find out that wasn't the issue if you guys can help it will be very appreciated

@cincomorales 6 жыл бұрын

Love the video also you are a great teacher! You did an amazing job cheers ! God bless your heart

@1AAuto 6 жыл бұрын

+jessie morales Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/toyota-camry-solara-engine-oil-pan/i/1aeop00057?KZfaq&CTA+Comment&VIqEagP9h1w

@peterwallis4602 8 ай бұрын

Top video. Many thanks. Kind regards from Western Austalia.

@carlosgarcia-po1zr 3 жыл бұрын

I am grateful for all the information you are sharing!!!thanks 👍👍👍👍👍👍

@carlotv1212 7 күн бұрын

Great video nonetheless I was just wondering from the list why I needed the mallet

@soyeldiego4878 5 жыл бұрын

Great video! Be doing this job this weekend. Hope it’s easy as it looks...

@1AAuto 5 жыл бұрын

+Soy Eldiego Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

@blessedbean8684 3 жыл бұрын

Hello! Thanks for this. All your videos are very clear and easy to understand. I wonder if you could tell me what SIZE & SPEC are the OIL PAN BOLTS. I know they are 10mm head but I mean THREAD SIZE and LENGTH. THANK YOU in advance!

@Superhyperaktive Ай бұрын

Great video, just one question; the block foam between the oil pan and transmission ripped apart when I tried to remove it. Im having trouble finding a replacement for it. Maybe i could just stick another piece of foam in there to replace it.

@joet4806 6 жыл бұрын

Great video! V Good Teaching skills, clear and concise. Exh. Flex joint ready to let go.

@1AAuto 6 жыл бұрын

+Joe T Thanks for watching. Have a great day! 1aauto.com

@hipolitoramirez424 3 жыл бұрын

very helpful good video also i bought some new suspension assembly also got the gasket set for the toyota camry and damn the 1995 is running like champ thanks to the videos.

@1AAuto 3 жыл бұрын

+Hipolito ramirez Thank you for your order! We'd love to hear about your experience. Here's a link to leave us a review on Google: goo.gl/i5JFNY

@elgatogordo9523 2 жыл бұрын

Interesting that it does not need an oil pan gasket, just silicone and that's it!!! My 97 Camry has an oil pan gasket installed and started leaking recently. I'll follow your instructions and use premium silicone on the oil pan flange. Thanks for the informative video 👍

@1AAuto 2 жыл бұрын

+El Gato Gordo Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@jessiejohnston905 5 жыл бұрын

Great video. Awesome. No complaints. Is it really better to use liquid gasket? I have the cork style.

@genericusername1365 5 жыл бұрын

The car was designed to use the FIPG sealant, not a traditional gasket. The torque settings were specified for the FIPG sealant and are thrown off if you use a cork gasket.

@darronlofton4998 2 жыл бұрын

thank you so much you guys are a life saver

@anonymike8280 2 жыл бұрын

I have a question here. You might know the answer. Is it possible to remove the oil pump housing without removing the oil pan? I think it might be possible to move it enough to get at the bolts holding the oil pickup to the housing. But maybe not. By the way, there is an aftermarket oil pan gasket available. That is what I would use, rather than silcone. Silicone requires the same skills as a cake decorator.

@djalal2327 7 жыл бұрын

how did you get the rest of the bolts off for the dust cover from the back side of the oil pan? size on those blots?

@Rekuzan 5 ай бұрын

Question: Why would you use RTV as opposed to a preformed cork gasket? What are the advantages/disadvantages of using RTV?

@thomassmith2056 6 жыл бұрын

amazing video 😁

@marks1034 5 жыл бұрын

Surprised sealer was spread and not left in a bead.

@bobbymoncada6861 Жыл бұрын

Thank you, sr. That was an amazing job.

@JaidenStylezTV 6 жыл бұрын

so what can i do if when i installed the exhaust back together and it start to leak?

@rickfingermancfp1239 3 жыл бұрын

Awesome job! Not fun but the prep is most important part of the job

@1AAuto 3 жыл бұрын

+Rick Fingerman, CFP Thanks for the feedback!

@shhway4590 3 жыл бұрын

What’s the cross reference or part number for the 10mm bolts for the oil pan ?

@kadenbatterman5288 5 жыл бұрын

Should be the same steps for a 5sfe mr2 right same motor

@zolof911 3 жыл бұрын

Tip: Watch the video all the way through before you start! Don't remove the insulator by pulling on it as shown at time 7:40. Once you remove the cover of the flywheel, the insulator slides off of the two posts. At time 17:30, he talks about this. Anyone know what the part number for this insulator is? On my 95 coupe, I did not need to disconnect the exhaust pipe to get the pan out. I found it more effective to tap downward on the lip of the pan at the front of the engine with a large pry bar in order to separate it from the engine.

@stacksjohnson5896 2 жыл бұрын

Is the V6 similar or harder? the local oil change place cross threaded my oil pan drain....bummed out.

@carlosmayorca4642 4 ай бұрын

You are the best!

@ohtanner 2 жыл бұрын

thank you!!!

@chieflouie2821 3 жыл бұрын

Why do AT pans have rubber/felt gaskets but oil pans have gasket makers (fipg)?

@FaisalAhmed-kf9yf 3 жыл бұрын

whats the time between finish seal and start drive the car ?

@imeralvarez5 3 жыл бұрын

I have a gasket I was told to put in, instead of just the adhesive you spread out, would it be a bad idea to put the gasket and use "the right stuff" to keep them together?

@phantomgaming8137 2 жыл бұрын

The haynes manual says to use both but after watching this video and reading through forums I'm going to just use rtv

@JacobMiller-wd7vx 5 ай бұрын

Was there a second torque after the initial torque at 48in/lbs?

@larryggoldman512 5 жыл бұрын

When I took the tailpipe down and removed the gasket between the two triangular pipes. I accidentally tossed it out thinking I could get a new replacement easily. But it hasn’t been as simple as you’d think. The parts house don’t seem to have the ceramic gasket in the correct diameter. Can your company send me the exact right size that fits inside the two triangle exhaust plates where we removed the stud bolts? Need ASAP!

@phantomgaming8137 2 жыл бұрын

Autozone has them, just purchased P#60906

@nealseamon8624 7 жыл бұрын

its my car thank you im down to hitting pan with rubber malit not dropping ill keep hitting are there any other trix im going to take oil filter off mybe relece some presure

@dgreatll 7 жыл бұрын

Neal Seamon Pressure should've relieved itself after draining oil from drain plug...

@gfriedman99 6 жыл бұрын

You need to cut through the old gasket to break the seal. You can use a stiff putty knife or razor blade.

@prodigeemd 9 ай бұрын

Is this the same steps for the V6 engine?

@aarondensmore7083 6 жыл бұрын

Hey I’m looking under my camry, it’s a 98 and it looks like the dust cover or insulation plate that you called it in the video needs to be replaced. Do you have a part number or a more detailed description of what it is? Thanks

@1AAuto 6 жыл бұрын

+Aaron Densmore We currently do not carry this particular part. Thank you for asking.

@JohnJones1987 6 жыл бұрын

There's a big gear under that thing - i'm guessing the fly wheel to the transmission? Anyway, my camry is a bit dirtier than your beautiful show model! But i'm not sure if i should clean that area up with some brake fluid cleaner, or just leave it alone. Unlike the oil pan, this cover doesn't seem to do much... i might make things worse...

@JacobMiller-wd7vx 5 ай бұрын

Was there a second torque after the initial 48in/lbs?

@Ionlyexistpardner. 2 жыл бұрын

How many hours spent on this job? And what is the name of the gasket sealer.

@user-pw5xd4yq8s 3 жыл бұрын

สุดยอด

@1AAuto 3 жыл бұрын

+จักรพงษ์ สุครีพ Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@Kit2Kay 6 жыл бұрын

is it ok to use a regular oil pan gasket

@1AAuto 6 жыл бұрын

+Kit2Kay Yes you can use an oil pan gasket for this oil pan. Thanks for asking. 1aauto.com

@itsmerch5615 Ай бұрын

So instead of an oil pan gasket it’s just a sealant?

@calebproductions5970 3 жыл бұрын

Is there a vid for doing this on an 04 Camry?

@1AAuto 3 жыл бұрын

+caleb productions We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c

@jasonduarte95 6 жыл бұрын

One of the oil pan bolts broke, what size are they?

@1AAuto 6 жыл бұрын

+jason duarte Your local dealer should be able to get the correct size for you. Hope this helps you out.

@_baller 5 жыл бұрын

Never seen anyone spread the on the pan...not sure that's a great idea

@lotusbomb7594 5 жыл бұрын

How much would this cost to fix +labor??

@barryf5479 5 жыл бұрын

Just had one done today. $522. They billed me 3.5 hour's labor. Frankly, I'm glad I had it done. Having a lift makes it a lot easier and doing it on ramps would be a real pain. Great video. Very professional.

@nihonkokusai 4 жыл бұрын

That downpipe can be replaced aswell

@pablogon98 2 жыл бұрын

This is an excellent video, I'll have to do it in a Corolla and it is not as bad engineered as that Camry hahaha. Thanks for uploading Also #Chrisfix'sArmy here: Don't use a metal tool to scrape the gasket on any surface, you could mess it up. Better to use a plastic scraper or a scotch brite abrasive sponge. PD: IDK about you but my next YT suggestion is named "How to PROPERLY use RTV to make a gasket" by Chris Fix. Go check it out.

@carlotv1212 7 күн бұрын

Did I miss the part where they used a mallet ?

@billytadlock9792 3 жыл бұрын

Did he remove the skid plate

@1AAuto 3 жыл бұрын

+Billy Tadlock This vehicle did not have a skid plate here but if your does it will need to be removed to access the oil pans.

@billytadlock9792 3 жыл бұрын

@@1AAuto so I'm working on the exact same car right actually I'm doing the water pump but I figured fuck it when I'm down there I might as well drop the oil pan and fix the leak would you recommend that I take the skid plate off

@850are2 3 жыл бұрын

What about a v6 tatorial?

@1AAuto 3 жыл бұрын

+850 ARE We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c

@reviewsunboxings12 7 жыл бұрын

That oil pan looks fine. I see no rust.

@1AAuto 7 жыл бұрын

It's hard to see from the video, but there was a small crack in the bottom of the pan that was causing a leak. 1aauto.com?KZfaq&CTA%20Comment&ATony 866-403-3393

@davidquillard3138 7 жыл бұрын

1A Auto Parts car repair videos

@davidquillard3138 7 жыл бұрын

1A Auto Parts car repair videos on KZfaq

@gfriedman99 6 жыл бұрын

These pans are steel. Up north they will rust thru in 15 to 20 years.

@gregorymcspadden8164 5 жыл бұрын

i would hire you as we all know a lot of mechanics will leave bolts in there pockets and do a half ass job and yes i say most mechanics and just to bad for you mechanics that do that kind of shit work because you are shit ya you don't go through life short changing work ethic man just look at this guy a true HONEST mechanic

@richardeckley8038 Ай бұрын

☺️

@JamesBrown-hv1xu 9 ай бұрын

Kazoontight

@debbiequintal4177 2 жыл бұрын

Wonder why this man does NOT wear safety eyeglasses to protect his precious eyes

@nealseamon8624 7 жыл бұрын

pan is not dropping anyone have thoughts help please

@gfriedman99 6 жыл бұрын

Neal Seamon try a pry bar or screwdriver to wedge it apart.

@iMMoRTalxm 5 жыл бұрын

Don’t use a pry bar you will dent it and loose shape of the sealing. Use a rubber mallet they are like 4$ at autoparts

@genericusername1365 5 жыл бұрын

Tap a plastic putty knife it there to break up the old seal. You could use a metal one or a razor blad if you are very careful not to put scratches/cuts in the metal.

@poolpoolification Жыл бұрын

no gasket? hello? theYmake a GASKET FOR THIS CAR

@kimchee94112 Жыл бұрын

Toyota makes maintenance so complicated and time consuming with a lot of cursing working upside down on the ground. What's wrong with a single regular gasket? Using this glue will make it more difficult to remove and clean the pan next time. My 2000 V6 Camry is nothing like this, the trans and engine oil pans are located in flip/flop positions.