How to Replace Exterior Mirror 2007-2013 Chevrolet Silverado

Рет қаралды 81,281

Жыл бұрын

Buy Now!
New Mirror from 1AAuto.com 1aau.to/ia/1AMRE02529
This video shows you how to install the driver’s side mirror but the procedure will be the same on either side of your 2007-2013 When it comes to driving, it’s important to know what’s behind you and beside you. A broken side view mirror could put you at risk of an accident, or ticket! TRQ side view mirrors are engineered to fit your vehicle. Chevrolet Silverado.
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
Tools you will need:
• 10mm Socket 1aau.to/oaFW/1AXAA00017
• 7mm Socket 1aau.to/oaFW/1AXAA00017
• Trim Tool Set 1aau.to/oQW/1AXXX00006
• 1/4 Inch Ratchet 1aau.to/oaFW/1AXAA00017
• 3/8 Inch Drive Ratchet 1aau.to/oaVk/1AXAA00015
• Gloves 1aau.to/osC/1AXSS00048
• Safety Glasses 1aau.to/onE/1AXAA00343
• Pick 1aau.to/oBh/1AXAA00037
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 20

@TRQ Жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@nonniefee 4 ай бұрын

I just did this ALL BY MYSELF! (62 year young great grandma!). Thank you for this video! I’m so glad I didn’t have to tell anyone I hit the garage door and smashed the rear view mirror!

@sawgrass3256 9 ай бұрын

You can do all of this without taking off the door panel completely… just let it hang off a little bit..

@Berkner80 Жыл бұрын

Love how they make it look so easy. That little quarter panel was a pain to get off and the was really stuck in there also.

@garycampbell6031 8 ай бұрын

Thanks. Your videos are top notch.

@coolcoolh2o 5 ай бұрын

Great video, super helpful. I replaced both my mirrors in about 1.5 hours. You don't need to completely remove the vapor barrier and mine just stuck back on easily.

@TRQ 5 ай бұрын

+@coolcoolh2o Thanks for the feedback! 1aau.to/m/Shop-TRQ

@danielburns7519 3 ай бұрын

all in less than 9 minutes. bravo

@bwest9840 Жыл бұрын

In regards to the white vapor barrier, were you able to reuse the Butyl Tape when putting it back on or did you have to replace that? Thanks.

@rgbuckl Жыл бұрын

Does anyone know how to retrieve that top nut he dropped into the door frame? The same exact thing happened to me. He never acknowledged it and magically had it afterward to install the new one.

@etp_23 Жыл бұрын

Do you all have the side mirrors with the 10 LEDs in the turn signal? I have an 09 avalanche ltz with the turn sgnal on the light that has more leds than that one

@seanpaula8924 Жыл бұрын

Thanks 👍

@rushkeeper00 8 ай бұрын

If my mirrors are non-powered do I still need to take the door panel off? Thanks

@nightshade-cg8ll Жыл бұрын

I installed them. But, now when i put it in reverse the passenger mirror wanders around. Would be fine but when i put it back into drive it dont return to its original spot. Suggestions?

@corylane1236 8 ай бұрын

They post a' How to do It yourself video, then GHOST everyone who asked questions about the process, I Unsubscribed moving on to Channels that will reply.

@alejandroponce2136 4 ай бұрын

I just bought these to replace on my 2008 chevy and the RH Mirror dont sit flush on the door i dont know whats wrong... i compared it to the original one and it seems that the one i recieved has the metal part of the mirror sticking out about 1/2in and that prevents it from mounting flush. I will contact customer service first thing tomorrow morning