How To Replace Front And Rear Struts On A 2008 Toyota Camry

Рет қаралды 126,766

8 жыл бұрын

Here are some of the tools that jimthecarguy uses
www.amazon.com/shop/jimthecarguy
In this video I will show you step by step how to replace front and rear struts The strut I use are called quick struts .They are a complete assembly.Remove the rear seat can be a real pain but I will show you a easy trick to get it out as easy as 1,2,3.
Due to factors beyond the control of jimthecarguy, it cannot guarantee
against unauthorized modifications of this information,. jimthecarguy
assumes no liability for property damage or injury incurred as a result
of any of the information contained in this video. jimthecarguy
recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of jimthecarguy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not jimthecarguy.

Пікірлер: 234

@ahmadghosheh3104 5 жыл бұрын

Jim, your videos are so well made and so complete and don't miss anything. Thank you for your work.

@paulfroelich1024 5 жыл бұрын

WORD.

@garysamyn3670 4 ай бұрын

I agree with the previous comments. Clear, patient and thorough. I do ha e a question; would u please send me torque specs and the type of 6mm socket/Allen wrench? Appreciate your videos and help. Blessings to you, Gary

@rowena3349 Жыл бұрын

Im absolutely understand everything you demonstrate very clear.

@ace5590 6 жыл бұрын

Jim, thank you for your thorough, detailed video. After watching your video I was able to successfully change all four struts on my 2007 Avalon, great work on your video!

@robrogers9837 7 жыл бұрын

I just finished changing all 4 struts on my 2008 Camry. I could not have done it without your help. Thanks! This video was perfect. No hidden surprises.

@jimthecarguy 7 жыл бұрын

thank you for your update and for watching.

@stephenohluk2019 3 жыл бұрын

All the little helpful hints were great, such as putting a nut BACK on ( slightly ) Before you start banging on it to slide out---so as to Not mushroom the end...Other strut videos the guys are hammering on the ends like crazy ! Jim was fortunate to have a LIFT, instead of working on the ground with a jack & stands, so he was able to use his HIP to install the lower strut bolts 1st, then reach up to get the top one started. Love the tip using a Big screwdriver to loosen the back seat hooks & keeping the integrity of the seat frame intact ( instead of bent ). These videos aren't worth a damn if those nuggets of gold aren't exposed for DIY'ers---thanks Jim for saving people loads of anger & frustration---over the hang-ups & pitfalls people encounter trying to save their hard earned money & do it themselves.

@hggm7855 6 жыл бұрын

Jim you rule this medium. You are detailed, fully explain every step, and why, then walk us thru. Keep the good videos coming. A sincere thank you.

@hammer18 3 жыл бұрын

Thank you. You are a very good teacher, thorough but concise. I feel like you genuinely want to pass along knowledge to those who seek it.

@jbpost52 2 жыл бұрын

Jim, thanks so much for making these videos to help out the DIYers. The truth is you can teach an old dog new tricks provided they are willing to learn. I just previously viewed the Camry video you did on rear sway bar bushings and link for a customer. Your blogs are becoming my number one location for instructional videos. Keep up the good work your providing.

@edwardbarone4257 4 жыл бұрын

@jimthecarguy this video helped me so much this past weekend for installing new quick struts. Very detailed and explained every step. Thank you so much for making these videos.

@flytheater 8 жыл бұрын

Your video helped me changed the rear struts on my 2008 Toyota Avalon. Im back hear because its time to change my front struts. This video helped save me hundreds of dollars from local mechanic shops. Thank you so much.

@jimthecarguy 8 жыл бұрын

Thank you for watching and your input.

@calebhunter8390 7 жыл бұрын

jimthecarguy I was hoping you could give me the torque specs for the 2 19mm bolts that connect the strut to the wheel hub assembly for a 2002 Toyota Camry LE 2.4l

@ninar5735 4 жыл бұрын

Great Job Jim. 3 years later and your video is still useful. Thanks

@Muddturtle3 8 жыл бұрын

This is great, truly appreciate how informative and well documented each step is.

@kristianjulian6255 2 жыл бұрын

instablaster...

@kevinsosa8209 Жыл бұрын

@the-macjagger Жыл бұрын

Thanks a ton Jim. You have a pleasant speaking voice and easy to understand way of explaining things. Just watching this one last time as I head out to the garage to change 4 struts for my daughter's project Camry, her 1st car.

@Jim-ro5pt 6 жыл бұрын

Your videos are really helpful. Only took me two hours to replace both struts on the front. Thanks for making the videos.

@jimthecarguy 6 жыл бұрын

Jim Crocker You did a good job in a short amount of time. Thanks for watching!

@reeefing 5 жыл бұрын

Amazing informative video. I am now READY for a DIY in my vehicle. Thank You very much👏🏻👏🏻👏🏻

@teresamish 3 жыл бұрын

Thank you Jim. I need to do this soon. Your videos are always well explained👍👍

@unebonnevie Жыл бұрын

Great camera work and details! Thank you so much for explaning the procedure in details. I am looking to replace my Lexus' struts.

@actl786 4 жыл бұрын

Thank you so much. Really appreciate your detailed extra tips not found anywhere.

@Delmar829 6 жыл бұрын

Thank you so much for taking the time to do this,

@roberthornwoodturner 6 жыл бұрын

Thank you for the very clear demonstration of how to do it right.

@OldElvis1927 8 жыл бұрын

Incredibly good video, Jim. Thank you so much for the lengthy explanation.

@jimthecarguy 8 жыл бұрын

Thank you for watching and your input.

@charlest.342 7 жыл бұрын

you were so thorough, this video made the installation much easier than anticipated. Thank you so much

@jimthecarguy 7 жыл бұрын

Charles T. Thank you for stopping by the shop

@normansmith7806 8 жыл бұрын

Great job Jim, each step explained very clearly !

@jimthecarguy 8 жыл бұрын

+N Smith Thank you!

@ahmadghosheh3104 7 жыл бұрын

Now THAT'S a detailed video. I imagine a 2009 I have wouldn't be too different. Thank you for a the good video and thank you for not having an annoying background music like other videos. LOL. Also a good trick to hold the brake rotor is to lift it with a small jack and keep it there until you are done, this works good for DIY that don't have a large lift.

@jimthecarguy 7 жыл бұрын

Ahmad Ghosheh Thank you for stopping by the shop

@chrissounddude3172 7 жыл бұрын

You are awesome for posting this video, thank you!

@diane2097 7 жыл бұрын

Very informative, easy to follow and clear shots with the camera. Great video!

@jimthecarguy 7 жыл бұрын

Diane McCoy thank you for your feedback and for watching

@rkgsd 3 жыл бұрын

Good point about liking to tighten the 3 nuts up top with a ratchet to get a better feel for the tightness. The mechanic who installed my rears didn't do that. Now 6 months later there's lots of rattling from the rear deck as if the strut is going to fall off. I can actually yank on the coil spring and hear squeaking above it.

@stephenohluk2019 3 жыл бұрын

Experienced mechanics have tightened SO many nuts & bolts over the years, they go by " feel "---but I'm sure they should be using the proper torque specs---kinda makes me mad that they don't. I don't know how much MORE time it would take---this strut came out/in---much sooner than the hour they charge us for...you'd think they could use a torque wrench just for " anal " sake.

@williamclick9771 3 жыл бұрын

You make that look so easy. I also have a 2000 Toyota Camry LE 4 cylinder that all the struts and shocks need to be replaced. 21 year old struts and shocks. My driver side rear is leaking fluid. They probably all do. The Camry was given to me by my cousin. It was his father's Camry. I'm on a limited income. I have a friend that works at Advance Auto Parts he told me to buy Suncore struts and shocks. So I bought them. I don't know how good they are. Like I said you make that look so easy.

@theclarkfamily1686 7 жыл бұрын

This is a great video, very well done. Thanks so much for doing this!

@jimthecarguy 7 жыл бұрын

Thank you for stopping by the shop.

@matthewsandoval253 Жыл бұрын

One of the BEST maintenance videos I’ve seen on KZfaq. 👍🏼

@jimthecarguy Жыл бұрын

Wow, thanks!

@synow86 7 жыл бұрын

This Is a great video. Thank you very much for taking the time to make it.

@jimthecarguy 7 жыл бұрын

Thank you for stopping by the shop

@Amelia-wl4lq 2 жыл бұрын

Great video, thank you for your time and help.

@atxjax1 4 жыл бұрын

On a job like this I like to start by doing the rear first. Remove the seat and the side bolster before touching anything else to avoid getting the customers upholstery dirty. Great video.

@stephenohluk2019 3 жыл бұрын

Wish all mechanics avoided making dirty handprints, kudos for being thoughtful !

@ramonlopeziii217 6 жыл бұрын

Excellent video and easy to follow instructions. Thanks

@jimthecarguy 6 жыл бұрын

Ramon Lopez III Appreciate the comment, thanks for watching the video.

@anthonyjr7502 5 жыл бұрын

Fantastic job,well done!

@jimthecarguy 5 жыл бұрын

I'm happy to help. Thanks for watching.

@Wayman_Simmang 4 жыл бұрын

Thanks for this video.. great job!!

@wyattoneable 8 жыл бұрын

That was a big job plus all the camera set up, thanks for letting us look over your shoulder. Next time I'll hold the light for you. :)

@gregstephens2754 5 жыл бұрын

Hey Jim. After seeing this video I have decided to bye my struts and install them myself. I have probably watched your video at least 15 times now and my 2008 Camry is on jack stands buddy! Thanks for your help with the video! Greg from Jackson, Wi.

@jimthecarguy 5 жыл бұрын

Good luck. I do a live stream on Sunday night on jimthecarguy at 7:00 PM (EST) .I will talk about this I hope you can stop by for the live stream

@gregstephens2754 5 жыл бұрын

jimthecarguy thanks Jim for your response on your live stream! I did buy the quick struts! But because I did not have an impact gun it was extremely hard to remove to lower bolt on the strut. I was told to heat up the bolt to try and loosen up the bolt now. Unfortunately I did have to take it to a shop but was charged and extremely low price for them to put on the rear struts. 😉 . This week a good friend on mine has invited me to bring my car to his garage so I can use his air gun on the front struts. Thank you for all of your videos. I am learning a lot. Greg from Jackson,Wi.

@johnranger293 4 жыл бұрын

Thanks for this tutorial. Very well done. I'm going to give this a shot as soon as it gets a little cooler out. I wish you was my shop teacher back when I went to Automotive H.S. . But then you would have to be about 110 now. :) Thanks.

@jimthecarguy 4 жыл бұрын

Hahaha some days I fell like I'm 110 .Thanks for watching.

@leeceebtsimuajlawm92 2 жыл бұрын

A great video and process explanation.

@rmp608 8 жыл бұрын

Excellent video!!!! Great how you go step by step.!! You should be a teacher!!

@jimthecarguy 8 жыл бұрын

+rmp608 Thank you for watching and your feedback

@jlevorse 7 жыл бұрын

Great video Jim. This is going to be a weekend project for me. What sockets did you use to connect/disconnect the strut from the knuckle?

@scottlacy6886 5 жыл бұрын

Jim, I would like a little more advice along with this video, regarding an order of operations. I am replacing both front axles, lower control arms, tie rods, and struts on the front. On the back I am replacing the rear struts and rear track arms. This is on a 2008 Lexus ES350, I've got 270,000 miles on the car. A general website with the torque specs would be very helpful, because I don't have an air compressor with an impact. Thank you for your videos and the help they have given me! God bless!

@flytheater 8 жыл бұрын

Best how to video l've seen so far. Do you have to perform an alignment after this type of job?

@SteveRobReviews 8 жыл бұрын

Fantastic Jim, best intro I've seen so far, good stuff buddy. Ok back to the vid. 👍👍

@normansmith7806 8 жыл бұрын

+STEVE ROB Yes Steve really like the intro !!

@jimthecarguy 8 жыл бұрын

+STEVE ROB Thank you Steve.How is every thing up North?Starting to melt a little?

@SteveRobReviews 8 жыл бұрын

jimthecarguy Actually today is about 45 on the F scale and pouring rain. Snows almost gone but up at my camp its 4 feet high and -18 at night. Looking forward to the spring getting tired of winter by now. On to the bug season. LOL

@jimthecarguy 8 жыл бұрын

+N Smith Thank you

@johnnycee5179 3 жыл бұрын

This is great. Thank you for taking the time to film, instruct and upload this. What struts would you recommend for that car? Parts from parts stores are iffy. Sure, you have lifetime warranty but it's for the part not the labor and it's the labor that costs so much.

@eddiemartinez265 8 жыл бұрын

Great work jim like the intro!

@jimthecarguy 8 жыл бұрын

+eddie martinez Thank you Eddie

@tonyde6744 5 жыл бұрын

Thank you . Great teacher!!

@bondiatube 5 ай бұрын

Many thanks Jim, great explanation.

@jimthecarguy 5 ай бұрын

Glad it was helpful!

@marktheunitedstatescitezen185 6 жыл бұрын

This Listen he gives “ little nuggets of gold “ to prevent hardships

@dontusegmail1218 7 жыл бұрын

thank you for posting this

@RobertAnkiewicz-ty8dt 11 ай бұрын

Jim thanks for your knowledge on the CAMRY i have two identical Camry's

@jimthecarguy 11 ай бұрын

Glad to help

@mae2759 5 жыл бұрын

Hey Jim, great video! Would you kindly post the torque specs for a 2008 Toyota Camry Hybrid?

@sergiormoralesdeleon 5 жыл бұрын

It's a greate video thank You very much for your information

@ampstreamz Жыл бұрын

thank you! saved me some time getting to the top nuts!

@1234jeffjeff Жыл бұрын

Thank you For showing all the little tricks there especially that backseat I appreciate you thank you

@jimthecarguy Жыл бұрын

You are so welcome!

@pedroc88 7 жыл бұрын

What sizes are the nuts? I ask because I may not have the right equipment and I'd like to be sure I order the correct wrenches.

@barclayporter1031 6 жыл бұрын

Excellent video. Thank you very much!

@jimthecarguy 6 жыл бұрын

Thank you for watching

@tedharper9550 7 жыл бұрын

When doing struts, are you suppose to use some type of lube to prevent squeaks? Great video. Very informative.

@MrJcardimen 7 жыл бұрын

Great video. Very helpful.

@jimthecarguy 7 жыл бұрын

Thanks for stopping by the shop.

@fazir22 8 жыл бұрын

Thanks Jim you're a good man👍

@jimthecarguy 8 жыл бұрын

+fazir22 Thank you for your input and for watching

@elielcantu9099 7 жыл бұрын

What are the torque specs on the top mount nuts for the front and back?Also for the 22mm front bolts and 19mm bolts for the rear?.

@jessepaz6406 3 жыл бұрын

Great video dude!

@jimthecarguy 3 жыл бұрын

Glad you enjoyed it

@Cronus_Primus 5 жыл бұрын

Great video and great work Thank you.

@jimthecarguy 5 жыл бұрын

I'm happy to help. Watch for the next free tool giveaway coming soon.

@jylee1969 6 жыл бұрын

You are the best. Thank you~!!!

@ashrafsiddiquee3190 Жыл бұрын

Hay Jim, I really appreciate all your video. I drive the same car and did the brakes yesterday and next want to do the rear struts just like this video. Could you please tell me which struts did u use in this video ??? Thank you soo much Jim. Again your video encouraged me to do the DIY work in the vehicle. Thank you

@kimchee94112 Жыл бұрын

Thanks for the comprehensive video. With the prices all over the map, who makes a good quality aftermarket strut that would last a few trouble free years?

@wayneleis6878 2 жыл бұрын

Great Video. I am looking for torque specs, for 2005 Toyota Avalon rear struts for the 15 MM bottom bolts. Thanks

@omardominguez3652 5 жыл бұрын

Hi Jim can you tell me the torque specs for a Toyota Camry 2007 SE V4. Thank you in advance.

@sebasp5023 2 жыл бұрын

Tks for your video so helpful....

@elielcantu9099 7 жыл бұрын

Also great info video very helpful thanks.

@jimthecarguy 7 жыл бұрын

Thank you for watching and your feedback

@saiket1735 6 жыл бұрын

Is it better to buy OEM part or after market part? a complete OEM strut assembly is very hard to find on the internet, I assume that only car dealers carry them.

@fadiamine2503 3 жыл бұрын

I have to replace strut mounting what there is a little triangle printed what does it means plz ? THANKS FOR YOUR HELP

@joet4806 7 жыл бұрын

Very Good Video! Very detailed and thorough for all the steps. Do you recommend installing never seize on the main bolts for the struts? ( bottom large bolts)

@jimthecarguy 7 жыл бұрын

Yes a little never seize is always a good idea.

@Reuben945 8 жыл бұрын

Great job! Thank you.

@jimthecarguy 8 жыл бұрын

Thank you for watching and your input.

@LuisHernandez-mo2xq 4 жыл бұрын

Thanks you so much for teach me how to do it

@arlenenunez9542 7 жыл бұрын

that help me, thank very much

@jamescahill3390 7 жыл бұрын

Best video on KZfaq especially the part about securing the front axel. I just did my rear struts. They were difficult to fit in. I had to lift the stabilizer links with a bar to get the studs back in the holes. Could this mean that my rear wheels need a realignment? Going to do the fronts today. Thanks again Jim.

@jimthecarguy 7 жыл бұрын

Thank you for watching and your input

@stevetran3862 5 жыл бұрын

thank you Jim

@jpg_sig10 7 жыл бұрын

My wife drives a 2008 Toyota Camry XLE V6, used for a mix of local and highway driving in the Phoenix, AZ valley. She drives an average of up to about 18,000 miles per year. How long should she expect these Monroe Quick Struts to last, presuming all four are replaced at the same time, and proper front and rear wheel alignments are done promptly? Thank you. Very informative video.

@doverperronnewyork8997 Жыл бұрын

You are the best

@toiletsareusable5988 2 жыл бұрын

Great video! You should definitely put the torque specs in the description or even reply to this comment with the specs. Would be much appreciated!!

@jorgewong910 Жыл бұрын

Jim, What quickstrut brand did you use? Which one do you recommend?

@samd410 7 жыл бұрын

you are an awesome mechanin.....keep The videos up?......?thanks

@jimthecarguy 7 жыл бұрын

thank you for your input and for watching.

@Williamcole10 2 жыл бұрын

I'm making this comment before I look at the whole video and I'm also not having checked out your entire channel but any possibility you have on this car change the bushings and the rear I'm thinking I might have to do that and I don't know what exactly they're called or if I have to buy a whole different piece or what piece to get

@fanzfanzilla 2 жыл бұрын

Thanks, Love it.

@jimthecarguy 2 жыл бұрын

Glad you like it!

@mikesbeardeds6462 Жыл бұрын

Thank you.

@greglarsen3248 7 жыл бұрын

I would think he would have the specs in his head and reveal them to us on this video. I used a wire brush to clean the stabilizer stud and sprayed with oil. Came right off. I also used a small jack to hold and raise the frame to line up the bolt holes. Other that this, good video.

@TimothyHall13 7 жыл бұрын

I found some torque specs. Correct me if I am wrong. Strut to Knuckle bolt: 152-166 ft lbs Sway bar nut: 29 ftlbs Suspension top 3 nuts: (rear) 37 ftlbs (front) 59ftlbs Brake line bolt: I bet 25-30 ftlbs would be good ABS sensor bolt: I bet 25-30 ftlbs would be good

@tommyanderson7453 6 жыл бұрын

Thank You for the excellent video. I saved cash and got some brownie points with the wife.

@twentyfive2life686 3 жыл бұрын

Can you send me specs for torque on the two main bolts

@doverperronnewyork8997 Жыл бұрын

Thanks

@SF-pq3cm 6 жыл бұрын

What is the name of those two huge bolts

@wendualx9251 8 жыл бұрын

Great job! One of the best videos I have seen. Think I'll do my own. What electric impact gun would you recommend for a DIYer. Thanks.

@jimthecarguy 8 жыл бұрын

Thank you for watching and your feedback

@flytheater 8 жыл бұрын

I used my Ryobi one + 1/2" impact driver to loosen my strut bolts. Worked perfectly.

@allenarias4517 6 жыл бұрын

Great video. Thank you so much. Saved me a lot of money

@jimthecarguy 6 жыл бұрын

Thank you for watching

@joebriggs9599 8 жыл бұрын

Top 3 nuts strip very easy on monroe quick struts. Have to go very easy on those.

@jimthecarguy 8 жыл бұрын

+Joe Briggs Thank you for your input and for watching

@dong102 4 жыл бұрын

Great.work, preciated

@jimthecarguy 4 жыл бұрын

My pleasure

@sirsweetness8332 4 жыл бұрын

Jim, on quick struts do you check the new coil bolt for tightness? I have heard of these coming from factory not tightened correctly leading to premature failure

@stephenohluk2019 3 жыл бұрын

Interesting---even tho they come pre-assembled---do we need to re-check the bolts ??

@tommyzDad 4 жыл бұрын

Hi, Jim. I just found this video. I just bought off of Amazon a full set of _Detroit Axl_ struts for my '03 Avalon -- should I have gone with Monroe or another brand? I fear now I didn't do quite enough research on what brand to get.....

@jimthecarguy 4 жыл бұрын

Sorry I never saw that brand before .I always use the Monroe struts and shocks. Thanks for watching.