How to Replace Front Window Regulator 1998-2011 Ford Ranger

No video

How to Replace Front Window Regulator 1998-2011 Ford Ranger

Рет қаралды 28,276

Күн бұрын

Buy Now!
New Power Window Motor & Regulator Assembly from 1AAuto.com 1aau.to/ia/1AWR...
Most power window problems can be traced back to either the regulator or the motor that drives it. TRQ produces affordable window regulators and motors that are designed specifically to fit your vehicle! This video shows you how to replace both the window regulator and the motor on your 1998-2011 Ford Ranger.
• Check here for more videos on the 1998-2011 Ford Ranger: • Ford Ranger 1998-2011 ...
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
Tools you will need:
• Phillips Head Screwdriver 1aau.to/omB/1AX...
• Pocket Screwdriver
• Pry Bar 1aau.to/oc5/1AX...
• 11mm Socket 1aau.to/oms/1AX...
• Cutoff Wheel 1aau.to/oh/1AXA...
• Rivet Gun & Rivets
• Painter's Tape
• Center Punch 1aau.to/oak/1AX...
• Hammer 1aau.to/odd/1AX...
• Pick 1aau.to/ock/1AX...
Subscribe: / @trq
Check out our playlist:
Ford Ranger 1998-2011 3rd Generation: • Ford Ranger 1998-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 14

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@gearhead366 Жыл бұрын

What do you do if the motor won't lower the window?

@tomn8tr 2 жыл бұрын

Too bad the owner never used Fluid Film in that door! Nice job changing the regulator, thanks for the video!

@TreyCook21 2 жыл бұрын

1) Is this a second channel of 1A Auto? 2) Dear God at the rust! The regulator is holding the bottom of the door on! 3) "Hooky Doos" Fan-freaking-tastic!

@kthwkr Жыл бұрын

The rust on the bottom of the door was bad enough that I would consider replacing the door. But ONLY IF that was a Southern vehicle. In the South that vehicle should last another 20 years. But it must be from the North and the salt is killing it. And any 2010 from the salt belt is pretty much at end of life now. So no reason to replace the door. And hardly a reason to replace the window regulator.

@stokestack 2 ай бұрын

Very helpful, thanks. The door panel differed on my 2009, so here are some notes that apply to later models: First, the door handle is a tray (no opening in the bottom), so the two screws are in the bottom of the tray. Remove those and then you can pry the whole insert that includes the switch assembly (the tray seems separate but pull the whole top panel) up to gain access to the other two screws that hold the door panel. The screw in the lower rear corner of the door panel seems to be captive, but if you try to remove the door panel after unscrewing it all the way you will break a plastic cylinder off the back of the panel and the screw will remain in the door. You must forcibly yank the screw out of the door and panel; its tip seems to get stuck in a plastic insert in the door frame.

@whiteshark7175 Жыл бұрын

Amazing very professional job......

@robertmay2649 8 ай бұрын

you dont have to do all those steps, the bar does not have to be removed. you can still get the regulator out no problem

@stephankayan2282 29 күн бұрын

What size are the mounting hardware you used ?

@ejones0310 9 ай бұрын

My Driver’s side window rocks forward and backward for about the first six inches of downward travel and the smooths out. It raises smoothly with no issues. Douse that sound like the mechanism just needs to be cleaned and lubed as well as the channels the glass rides in?

@tomprohaska2150 Жыл бұрын

What size bolt replaced the rivets?

@kthwkr Жыл бұрын

Yes. My question too. And the length is important. They need to be long enough to do the job. But if they are too long they can get caught on things as the window goes up and down.