How to Replace Rear Shocks 11-14 Hyundai Sonata

Рет қаралды 63,067

1A Auto: Repair Tips & Secrets Only Mechanics Know

5 жыл бұрын

Buy Now!
New Shock Absorber from 1AAuto.com 1aau.to/ia/1ASHA00400
1A Auto shows you how to repair, install , fix, change or replace your rear shocks. This video is applicable the 10, 11, 12, 13, 14, Hyundai Sonata
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oy7/1AXAA00013
• 19mm Wrench 1aau.to/oeD/1AXAA00010
• 14mm Socket 1aau.to/ot3/1AXAA00015
• 19mm Socket 1aau.to/ofz/1AXAA00043
• 21mm Socket 1aau.to/ofz/1AXAA00043
• 1/2 Inch Breaker Bar 1aau.to/oc2/1AXAA00078
• Ratchet 1aau.to/oy7/1AXAA00016
• Socket Extensions 1aau.to/ot3/1AXAA00015
• Torque Wrench 1aau.to/ohm/1AXAA00044
• Hammer 1aau.to/odo/1AXAA00091
For More Info visit us at 1aau.to/h/bE7/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 41

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@bobbyhummel3691 2 жыл бұрын

Great video. 2 Notes: 110 ft-lbs on that lower bolt like others have said When mounting the new strut to the mount, make sure you use a pair of pliers to grab the rod at the top and snug down that bolt. If you don’t you’ll get a rattling sound over bumps and will have to do the job over again (like me)

@danawd 2 жыл бұрын

One of the best video i saw for a diy! I will always double verify torque specs for any vehicle, even if someone told me what the torque is😁 you can also use the tip of the rod to hold it while losing it with a wrench also, it’s made for that… you never know if for any reason you’ll have to replace this old shock in place, bad new part, wrong part, etc😬

@sanityone649 4 жыл бұрын

Very nice video. Thanks for demonstrating the proper way to use a torque wrench.

@mannysosa5551 4 жыл бұрын

You just save me some money with this video!!! Easy to do it your self.

@1AAuto 4 жыл бұрын

+Manny Sosa Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

@bbdetailing9123 2 жыл бұрын

Good easy to follow video. Thanks

@butt2986 Жыл бұрын

Best video ever thanks for making such a great explained video 🙏🙏👌👌👍👍👍

@juancarrillo7701 2 жыл бұрын

very explain full thanks

@evensmoise5670 5 ай бұрын

Great job buddy 🎉🎉🎉🎉

@Jose.alfredo12 3 жыл бұрын

Awsome quality👍👍👍👍👍👍 I just did the same thing

@TheHousedigs 4 жыл бұрын

Great job on the video

@1AAuto 4 жыл бұрын

+TheHouse Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto

@danielrivera-us1cg Жыл бұрын

nice job

@vagnsorensen8345 11 ай бұрын

Thanks!

@scottgm321 4 жыл бұрын

This was the same for my 2012 Hyundai Tucson. I found it easier to line up the bottom and pop the bolt in then get the top in place. Easiest job ever. Thanks

@1AAuto 4 жыл бұрын

+scottgm321 Thanks for checking us out. 1AAuto.com

@GNARLOUSE 3 жыл бұрын

Thanks

@sosew829 4 жыл бұрын

awesome and informative video! i will say though the torque for bottom strut bolt is 110 ft lbs not 57 ft lbs

@Knufia 3 жыл бұрын

you're right. according to the manufacture's guide it's Tightening torque Nm(kgf.m, lb-ft) : 44.1 ~ 53.9 (4.5 ~ 5.5, 32.5 ~ 39.8) for the 14mm and for the 19 mm its: 137.3 ~ 156.9 (14.0 ~ 16.0, 101.3 ~ 115.7) (it's on an optima, but that's the same)

@lynelle1 3 жыл бұрын

Thanks for that info! I have to go back down there in the morning and tighten mine up a bit more as well.I had a gap between the shock and knuckle screw hole after only putting 57lbs of torque and was curious why but maybe this is the reason. Needs to be 110lbs

@Tradrnq 4 жыл бұрын

Is this similar to the 15 Sonata?

@Yourpapi666 11 ай бұрын

Do you guys know where I can buy a replacement bushing for the shocks?

@EL2OH8 Жыл бұрын

So mine has 17000k...and I want to do new struts...should I also do new springs in the back?

@AlbertTeesateskie Ай бұрын

I have a long wheel base 12 passenger chevy van,it has a very bumpy rear ride.What is best & type shock,no air shocks,to buy?

@graysonwagner1855 4 жыл бұрын

Should you not torque the shock nuts vehicle on the ground?

@xbluepuddingx 2 жыл бұрын

Should I use vice grips on the hydraulic arm when I go to torque the top nut back on? Well I guess I could throw a towel over it and use locking pliers.

@tomajefferson9020 6 ай бұрын

What is the part number for front and back stunts and shocks

@jfresh2054 4 жыл бұрын

What impact is that? Seems powerful

@user-vi1os8of8p Жыл бұрын

I have a 1/2 drive DeWalt impact works great

@user-ny3wj3sn1i 8 ай бұрын

Rule of thumb is do not tighten any of the bolts until they are all started

@alexkonwinskif9184 4 жыл бұрын

Great video but one question. The spec sheet for 2011-2014 sonata states the torque as the following : 137.3~156.9 N.m (14.0~16.0 kgf.m, 101.3~115.7 lb-ft) Your video shows 57 lb-ft - that's a difference of 50 lb-ft +/- a few. Couldn't this lead for problems?

@davidgarza995 2 жыл бұрын

Yes it definitely not suppose to be off by that much

@xbluepuddingx 2 жыл бұрын

Yeah they should probably take this video down and do another with correct torque bc people are dumb. Honestly, there was probably a good amount of people who didn’t realize we did in the past three years this video has been up.

@monomartinez6663 Ай бұрын

What about the rear coil spring

@matthewminiatt8810 2 жыл бұрын

Shocking!

@jamesstpatrick8931 3 жыл бұрын

Will I need an alignment after replacing both rear shocks ?

@1AAuto 3 жыл бұрын

+James St patrick Yes, an alignment will be needed for these parts.

@redlightdistrick2626 3 жыл бұрын

I changed mine and it’s now making noise like something is loose but nothing is I’ve torqued all bolts only thing I can think of is the bolt on top of the strut I dont get what else could be making that noise

@1AAuto 3 жыл бұрын

+redlightdistrick We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@bobbyhummel3691 2 жыл бұрын

I know this is one year ago but check that top bolt. I didn’t smug my down all the way and got a rattling noise. If you used threadlocker get your torch out and heat up the 2 under mounting bolts to get them free