How To Replace Rear Shocks 97-03 Ford F150

No video

How To Replace Rear Shocks 97-03 Ford F150

Рет қаралды 131,929

1A Auto: Repair Tips & Secrets Only Mechanics Know

Күн бұрын

Buy Now!
New Shock Absorber from 1AAuto.com 1aau.to/ia/1ASH...
1A Auto shows you how to repair, install , fix, change or replace your front shocks with their loaded struts. This video is applicable to the 97, 98, 99, 00, 01, 02, 03 Ford F150 pickup truck.
🔧 List of tools used:
• 10mm Wrench 1aau.to/ojL/1AX...
• 18mm Wrench
• 10mm Socket 1aau.to/oHo/1AX...
• 18mm Socket 1aau.to/omj/1AX...
• 1/2 Inch Breaker Bar 1aau.to/og8/1AX...
• Rust Penetrant
• Floor Jack 1aau.to/onN/1AX...
• Hammer 1aau.to/ohu/1AX...
• Jack Stands 1aau.to/onX/1AX...
For More Info visit us at 1aau.to/h/aFn/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 42

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@slowbutsure504 2 жыл бұрын

Nice. All of my bolts and nuts where 18mm. Love how they always change small stuff like that through production

@nathanshultis4811 Жыл бұрын

Mines 21mm

@19TheDan 4 жыл бұрын

Noticed that the new shock appeared much smaller in diameter? Seen similar company's cut corners like this to keep cost down... my question is hows the ride quality?

@mach275 3 жыл бұрын

Nice editing in this one

@EmanDeluxeVLOGS 5 жыл бұрын

I feel like a lot was edited in the removal of the top nut... I cut mine off at the rubber. Not fun. But ride 10 times better. Northeast 🚚. if only the guy before me replace them while the bed was off

@majorpayne5289 6 жыл бұрын

👍 good job & thx however, @ 3:45... Replaced? Get a hammer & pry-bar- it’s hi strength steel, stuff gets bent in/on/underneath a truck!

@briantucker9963 5 жыл бұрын

I have a 97 f150 4x4 and i do not have the access hole in the frame that you point out at the 54sec mark of the video. Oh how i wish i did. the threaded stud and nut at the top of the old shock is rusted together. vitually no room to access top nut. 14" vicegrip wont hold the polished shaft tight enough to break the nut. help

@elideedrick5116 Жыл бұрын

Snap it off. Doing what these people are saying will take days in a home shop. Or for your case you can’t get to it

@NorthTowerDesigns 5 жыл бұрын

Ha! Kenda Klevers! Great tire for a great price! Haven't seen very many truck owners run 'em.

@miguelrocha3522 5 жыл бұрын

Love them they are way more famous in the mountain bike atmosphere tho rhe brand that is

@605pilot Жыл бұрын

New shock looks thinner than the original Motorcraft shock.

@lukewarren7857 7 ай бұрын

Thanks Following instructions working out great

@bryanc.tejada2408 5 жыл бұрын

I have a 2003 SuperCrew F-150 is there a reason why the right rear shock has two different mounting positions one for in front of the axle and for behind the axle when I first got the truck the right rear shock was over the axle facing the engine but now I switched it to over the axle facing the rear????

@kitcarson6806 5 жыл бұрын

The right rear needs to have the top of the shock leaned toward the front of the pickup. The left rear needs to have the shock landed toward the rear of the pickup.

@paulhughes3810 Жыл бұрын

Is there a torque spec for top/ bottom or just as you said until the top stops and then just crank it down on the bottom?

@billypalangga1770 Ай бұрын

What if the lower part of shock won't go in to bolt it?

@rogue3095 Жыл бұрын

This video does not really apply to the 97s. Not sure when they made the changes to the rear frame but i know for a fact that my early 97 does not have the access holes in the frame. and top bolts are 18s.

@organicvids Ай бұрын

Does the 2003 f150 7700 take same shocks?

@BradlyJohn03 4 жыл бұрын

As for the upper mount... if you've an overly stubborn nut do you have a last resort kinda procedure suggestion? Technique?

@1AAuto 4 жыл бұрын

+BradlyJ03 We would suggest using some penetrating oil and letting it sit for quite a while to break up any corrosion. 1aauto.com

@BradlyJohn03 4 жыл бұрын

@@1AAuto finally managed. Took some effort. Couldn't get anything to grip. Ended on a pipe wrench.

@BradlyJohn03 4 жыл бұрын

Thank you

@StormLaker Жыл бұрын

So my 03 came with Rancho RS5000 shocks- do I have to put those back in (possibly oem lift?), or can I just put in any shocks? Just looking to replace for safety reasons and not spend a ton of money.

@alimohammond6323 5 жыл бұрын

i notice the new shock don't come with a bolt, i had to use the old one

@nastysoda9212 2 ай бұрын

the rebound on that new shock is INSANELY too low, that is a defective shock

@JamesRK2 5 жыл бұрын

I did mine with the bed off .... way easier

@jplinc.1194 4 жыл бұрын

mans can't use a hammer

@LuisHernandez-sk7iq 6 жыл бұрын

Can i do this without the truck being lifted in the air

@1AAuto 6 жыл бұрын

+Luis Hërñàñdëž Yes you can! 1aauto.com

@obedb093 Жыл бұрын

looks like those shocks dont do much work if your able to push them in so easily.

@foreverfixin 5 жыл бұрын

Can u run dual shocks on a F-150 Raptor

@Poprocks4u 3 жыл бұрын

How many people out there have a lift to raise their vehicle so they can perform this shock replacement??? Get real! Show us how to do it if you have to do it on the ground, in the dirt, and if you're lucky, on a concrete pad. That's why we come to 1A Auto! Otherwise we would take it to a shop and have someone do it for us!

@1AAuto 3 жыл бұрын

+Poprocks4u Lifting the vehicle makes it easier for our video crew to film the repair. Of course, we understand the vehicle does not have to be lifted to complete the repair.

@ForfeMac 2 жыл бұрын

Aren't you a whiny little biatch. It's the same shit on jack stands, you're just sitting on the ground instead of standing upright

@commanderstud2417 5 жыл бұрын

Does this apply to a four wheel drive?

@1AAuto 5 жыл бұрын

+Daniel Hinkle Hello, the rear shocks on a two-wheel drive and four-wheel drive will have the same procedure. Thanks! 1AAuto.com

@NebulousFox 6 жыл бұрын

any idea where i might be able to buy one of the lower shock brackets? mine is bent like you showed in the video but so much that i cant put new shock in.

@1AAuto 6 жыл бұрын

+NebulousFox We currently do not carry them. You may want to check Ebay. Hope this helps you out. 1aauto.com

@NebulousFox 6 жыл бұрын

for anyone else that may need. there are no oem or related parts for replacing the mount itself not even from ford directly. you must get an aftermarket, built or fabricated one to replace the old one and weld on. that is at least for the 98

@robvermeulen9149 3 жыл бұрын

Hammer and pry bar as previously mentioned. The steel mount is very forgiving, so don't be afraid to out some @$$ on it when you swing the hammer.