How to Replace Rear Wheel Bearing on a BMW E91, E90, E92

  Рет қаралды 57,124

Car Repair and Tools Videos

Car Repair and Tools Videos

Жыл бұрын

Full Detail Video Link: • How to Replace BMW E91...
DISCLAIMER 1: I am not sponsored by any means. Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting.
USA Amazon:
Universal Hub Puller: amzn.to/3IvN2VX
Tool Set: amzn.to/3mapZIT
Ratchet: amzn.to/3EFkU1G
Slide Hammer: amzn.to/3IWGcdC
Wheel Bearing Tool: amzn.to/3xVf7Bq
Bearing Race Tool: amzn.to/3IxZNQ2
Floor Jack: amzn.to/3xR8H6e
Jack Stands: amzn.to/3m9te3i
Tool Box: amzn.to/3IVNXjP
Breaker Bar: amzn.to/3KFXSeP
German Amazon:
Universal Hub Puller: amzn.to/3kvL53W
Ratchet: amzn.to/3m9T6Mv
Slide Hammer Puller: amzn.to/3IzlNtz
Wheel Bearing Tool: amzn.to/41salZz
Bearing Race Tool: amzn.to/3SyCppS
Floor Jack: amzn.to/3y14koZ
Jack Stand: amzn.to/3IWEd9h
Tool Set: amzn.to/3Y7XAjQ
Tool Box: amzn.to/3ITblP9
Breaker Bar: amzn.to/3Y5O6FI
Disclaimer 2: These videos are strictly for educational and entertainment purposes only. Imitation or the use of anything demonstrated in my videos is done at your own risk. I will not be held liable for any injury to yourself or others or damage to your firearms or any equipment resulting from attempting anything shown in any videos.

Пікірлер: 65
@6ixvamp
@6ixvamp Жыл бұрын
Brother, you’re smooth with it. Thank you for sharing this helpful video. Makes the wheel bearings less daunting
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Thanks for the feedback. This job is not that easy it looks but it do able if right tools are used.
@stamourphotography
@stamourphotography 7 ай бұрын
Thanks, woaa .... your good ...this more work than anticipated, plus I do not have those tools...now I am totally sure I won't be doing it myself but enjoy seeing you do it lol
@carrepairandtoolsvideos
@carrepairandtoolsvideos 7 ай бұрын
Lolzzz it looks harder than it is in actual. But yeah, right tools would be needed. But its doable on a drive way :D
@adnanfile
@adnanfile Жыл бұрын
i have seen complete guide as well.good work
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
thanks buddy
@kurtm54
@kurtm54 11 ай бұрын
This is a great video. How long did it take you to do? I've seen Dorman sells a whole wheel assembly/knuckle. Almost looks like it might be faster? Is it hard to remove the axle?
@carrepairandtoolsvideos
@carrepairandtoolsvideos 11 ай бұрын
Its heck of the job. If you have the right tools, you can do it between 2-3 hours. In my case the axle was stuck like a hell. I live in rust belt environment. But if you dont live in rusty environment then it should not be that hard to remove axle. Yes, it will be faster if get pre-assembled parts. I would personally do only wheel bearing if I have access (or borrow) to all tools.
@kkshangla
@kkshangla Жыл бұрын
Great job bro
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Thanks
@randlecycling2462
@randlecycling2462 Жыл бұрын
Thank you for your video. Which brand of swivel bar (beaker bar) do you use?
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Thanks. In this video, I was using Stahlwille breaker bar. I will review this breaker bar in my future video. Stay tuned 👍
@tonyross7376
@tonyross7376 8 ай бұрын
Good stuff bro👍. Looks like a nightmare of a job
@carrepairandtoolsvideos
@carrepairandtoolsvideos 8 ай бұрын
Thanks bro. I like this kind of challenging work :D
@tonyross7376
@tonyross7376 8 ай бұрын
@@carrepairandtoolsvideos lol try living in Scotland with the rusty cars that is a good challenge for u bro👍🤜
@carrepairandtoolsvideos
@carrepairandtoolsvideos 8 ай бұрын
@@tonyross7376 lolzzz I live in rust belt too bro :D BTW, love Scottish landscapes
@tonyross7376
@tonyross7376 8 ай бұрын
@@carrepairandtoolsvideos 🤜👍
@thomashofstadler2549
@thomashofstadler2549 Жыл бұрын
few pieces of advice from a dumb man currently in the trenches: 1. you absolutely need a torch to pull the drive shaft from the spindle. no exceptions. pb blaster is good too but doesnt come close to heat. 2. make sure your ebrake is OFF when you go to pull the hub. 3. he removed the sway bar connection to pull the shaft out. i also suggest looking upstream the ebrake line and diconnecting it from the wire bracket before trying any pulling. will update with whatever dumb stuff i learn next.
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Thanks for the valuable tips. However, this is a shorter version of the actual video. I have full 48 minute version of video where I used torch, hammering etc. I did not remove the cv axel due to the fact bolts were rusty and would strip as it happened to the other side. So I decided to undo bolts on control arms etc. Otherwise removing cv axle completely is easiest way as you mentioned along with sway bar link. Thanks for sharing your knowledge :)
@thomashofstadler2549
@thomashofstadler2549 Жыл бұрын
@@carrepairandtoolsvideos you got any tips for the c-clip? mine is putting up a real fight
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
@@thomashofstadler2549it gave me also a tough time. Just keep hammering enough with a flat head screw/chisel around the circlip and keep cleaning the rust around with some pick and hook with heating if you have torch. Check my detail video in the description, that might help you.
@cruelworldpk
@cruelworldpk Жыл бұрын
amazing work mamu
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Thanks
@peterwalton5768
@peterwalton5768 3 ай бұрын
I've seen other videos where you just pull the axel shaft. Much easier.
@carrepairandtoolsvideos
@carrepairandtoolsvideos 3 ай бұрын
You are spot on
@legioner9
@legioner9 2 ай бұрын
Nice. But removing the CV axle is easier than to remove the suspension arms bolts. Plus the alignment you need to do afterwards.
@carrepairandtoolsvideos
@carrepairandtoolsvideos Ай бұрын
Yes, you are right. Due to rusty bolts of cv axle, i avoided to remove that and chose to remove suspension arm instead. The car went for alightment at shop later
@DonMikson
@DonMikson 6 ай бұрын
Would it be faster if you took out the axleshaft? In my opinion, you unnecessarily disconnected the suspension arms because now you have to go and adjust the geometry. But general good job ;)
@carrepairandtoolsvideos
@carrepairandtoolsvideos 6 ай бұрын
I made a detailed video on this job where I mentioned that due to rusty bolts of drive shaft I chose this method. I did other side by removing axle and stripped the bolts which were insanely rusted. It was a nightmare. So I chose this method. Took little more time but worked for me. It will need alignment in both methods anyway. Thanks for pointing out that.
@jaskolukac5223
@jaskolukac5223 2 ай бұрын
Hey, nice work, but why you didn‘t simply pull out the driveshaft?
@carrepairandtoolsvideos
@carrepairandtoolsvideos 2 ай бұрын
Botls of driveshaft were rusted to extent will get stripped and it happened to other side. So decided this method :)
@norcalnights
@norcalnights Жыл бұрын
What is the tool called that was used to press the bearing in?
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Its called wheel bearing press. I made video on that too. Here is the link if you wanna check that out: kzfaq.info/get/bejne/hbOao5mFlpe6nqc.html
@kjosephf
@kjosephf Жыл бұрын
How did you know when to stop pressing the wheel hub into the wheel bearing? I over pressed mine and now the rotor won’t rest flush onto hub because now it’s rubbing on the backplate
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
You will feel when hub stop moving forward. I dont think you can over tighten cause you will feel it that its not moving forward. If you still over forced it very hard then its another story. Plate can be bent accidently during the job. try to bent the plate away from rotor and see it helps.
@MrFryfish
@MrFryfish 10 ай бұрын
You have done probably something else wrong.. to the date I am at the third bearing replaced on the rear, having 250k miles done with same car.. the bearing case should rest in the hub against the lip that is there inward, at the bottom. If you grease the hub prioir pushing the bearing you would have felt it. One good idea is to put the new bearing in the freezer couple of hours so it is shrinked slightly prior pushing... If you do not push the bearing to deep you would not be able to fit the clip inside behind the bearing...
@uknow7305
@uknow7305 Жыл бұрын
What’s the tools called that you use and the material list?
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
I have used few specialty tools. Slide hammer puller, universal hub puller, bearing race tool. I have put all the tool's link in the description section if you wanna check them out.
@fl4w1ess83
@fl4w1ess83 11 күн бұрын
Could i ask what is til name of the tool at the end of the gildehammer 2:22
@carrepairandtoolsvideos
@carrepairandtoolsvideos 10 күн бұрын
Wheel bearing press kit if I understand right. I have put all the links below in the description section every tool I used
@life-explorer
@life-explorer 11 ай бұрын
nice
@carrepairandtoolsvideos
@carrepairandtoolsvideos 11 ай бұрын
Thanks
@azmaymi9237
@azmaymi9237 8 ай бұрын
Nad wheel bearing can cause rear left no signal?
@carrepairandtoolsvideos
@carrepairandtoolsvideos 8 ай бұрын
Yes, some time it can cause but not always.
@joaomachado4056
@joaomachado4056 Жыл бұрын
Where is the point to jack the rear of the car? Tks for the video.
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
Here is the detailed video where you can see how to jack up the car properly from rear end
@MrFryfish
@MrFryfish 10 ай бұрын
Well, I bet that was an E91. At E90 you cannot jack the car up in the middle because at E90 is no middle point to lift the car up...
@dexta1961
@dexta1961 Жыл бұрын
👍
@user-nt7rl9xj5p
@user-nt7rl9xj5p 3 ай бұрын
How much should it cost at a garage to change both sides? 3:46
@carrepairandtoolsvideos
@carrepairandtoolsvideos 3 ай бұрын
Depends on the shop and location. It could cost from 600 to 700 $ including parts
@user-nt7rl9xj5p
@user-nt7rl9xj5p 3 ай бұрын
@@carrepairandtoolsvideos thanks,I’ve just been charged £530 including parts so it sounds about right
@azmaymi9237
@azmaymi9237 9 ай бұрын
Can bad wheel bearing cause abs light 4x4 light and break pulsating?
@carrepairandtoolsvideos
@carrepairandtoolsvideos 9 ай бұрын
Yes, bad bearing can cause abs light since bad bearing can send error signal to the system. Brake pulsating can happen too but its not so often. But its important to check properly whether its bad bearing or brake system's fault.
@DG-od4si
@DG-od4si 7 күн бұрын
👍👍
@carrepairandtoolsvideos
@carrepairandtoolsvideos 7 күн бұрын
👍
@cdeprima1209
@cdeprima1209 10 ай бұрын
I suggest lots of penetrating oil and let sit overnight for all fasteners, really! :(
@carrepairandtoolsvideos
@carrepairandtoolsvideos 10 ай бұрын
And Heating is the best friend for the jobs like that
@MrFryfish
@MrFryfish 10 ай бұрын
Is so much risk with the bearing not going straight or your tool not aligned precisely on top of the edge of the new bearing.. having so much play and movement in the hub being half dismantled.. you could remove the driveshaft first.. (of course HAVE THE CAR ON STANDS!) Then remove the bearing.. It takes energy on what you are trying to do... And yes as other said GENUINE FAG or SKF... DIYers, this is NOT an easy job. Mechanics themselves know this. Changing rear wheel bearing on BMW is not easy..
@carrepairandtoolsvideos
@carrepairandtoolsvideos 10 ай бұрын
This is the shorter version of the job. I have full 50 minutes detail video too on my channel. The bearing settled in nice and straight but it needs attention obviously. Yes, I could have removed the drive shaft but decided not to due to the fact bolts of drive shaft were rust and crusty and been rounded off on the other side. So I did not want it this side of the car. I avoid now chinese parts and go for SKF or FAG etc. It was not easy job doing on the drive way but with right tool it can be done effectively Thanks for sharing your thoughts
@felleice
@felleice 3 ай бұрын
Next time put it in the freezer before assembly
@carrepairandtoolsvideos
@carrepairandtoolsvideos 3 ай бұрын
Yes, I do that sometime. But it was easy to put in, it was super hard to remove though!
@luckyhack78
@luckyhack78 Жыл бұрын
One BIG mistake.... RIDEX.... BIG CHEAP CRAP!! bmw OEM bearings are from FAG , With cheap ridex or ebay bearings... 1 years? 2... dead..
@carrepairandtoolsvideos
@carrepairandtoolsvideos Жыл бұрын
It was budget DIY. But good to know. Next time it will be FAG
@vitalybrateev5548
@vitalybrateev5548 Жыл бұрын
@@carrepairandtoolsvideos FAG or SKF 30ish € both does bearing for BMW. For suspension its Sachs. Silentbloc its Lemforder. Brake , ATE. If you need an oem part brand name for a specific part, hit me up, these are BMW parts but without the cost of a BMW parts, when you buy it you can see they grind the BMW logo. Have fun
@MrFryfish
@MrFryfish 10 ай бұрын
100%FAG nothing else. There is to much work (and money) to put cheap bearing...
Scary Teacher 3D Nick Troll Squid Game in Brush Teeth White or Black Challenge #shorts
00:47
KINDNESS ALWAYS COME BACK
00:59
dednahype
Рет қаралды 159 МЛН
How to Replace BMW E91, E90, E92 Rear Wheel Bearing. Ultimate Guide Step by Step
48:59
Car Repair and Tools Videos
Рет қаралды 65 М.
Control Arm Bushing Replacement // BMW E90
8:53
JD Cars
Рет қаралды 164 М.
2015 BMW 535d AWD Rear Wheel Bearing Replacement
29:18
Tech28
Рет қаралды 1,8 М.
BMW E90 ABS Fehler / Antriebswelle und ABS Sensor ersetzen / E87 / E90 / E91 / E60 / E61
18:03
BMW Technik & Coding / Tutorials
Рет қаралды 36 М.
Rear Wheel Bearing Removal With No Special Tools BMW 3 Series
7:35
EdzGarage
Рет қаралды 1,3 МЛН
BMW E90 E92 328xi rear wheel bearing replacement
37:56
You can fix it
Рет қаралды 691
BMW 3er E91 Radlager hinten wechseln Allrad
25:08
M aus G
Рет қаралды 62 М.
Водитель бмв не ожидал такого #дуракинадороге #shorts
0:18
УСТРОЙСТВО ДЛЯ ВЕЛОСИПЕДИСТОВ (@heumoedernlift)
0:18