How to Replace Spark Plugs 00-04 Ford Focus

Рет қаралды 32,813

1A Auto: Repair Tips & Secrets Only Mechanics Know

6 жыл бұрын

Buy Now!
New Spark Plug from 1AAuto.com 1aau.to/ia/NGETK00040
1A Auto shows you how to repair, install, fix, change or replace old or defective spark plug wires. This video is applicable to the 01 Ford Focus.
🔧 List of tools used:
• 5/8 Inch Spark Plug Socket
• Ratchet 1aau.to/oakM/1AXAA00016
• Socket Extensions 1aau.to/o5Y/1AXAA00015
• Torque Wrench 1aau.to/ovF/1AXAA00044
For More Info visit us at 1aau.to/h/bin/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 29

@1AAuto 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@toolsilike 6 жыл бұрын

Helpful Thanks 1a auto

@GetRealBaby 5 жыл бұрын

Thanks for this video. I might not have thought to blow out the dirt. Where does that dirt go?

@madhippy3 26 күн бұрын

I have a problem where the spark plug unscrewed and was bashing the wire against the hood while driving on the highway. If we cannot get the plug to screw in should we assume that the hole it sits in has lot its threads?

@geoas9959 5 жыл бұрын

shouldn't you put a little never seize on the threads?

@nevakainindustries4350 4 жыл бұрын

Plus one for the never sieze. Especially on the manifold bolts

@mat2436R 5 жыл бұрын

Should the valve cover gasket be replaced?

@1AAuto 5 жыл бұрын

Thanks for checking us out! The valve cover is not required to be replaced but if you do notice it beginning to look worn we would suggest having it replaced as well. Hope this helps you out! +Mark Tharpe

@nevakainindustries4350 4 жыл бұрын

Exactly

@bradenanderson5087 5 жыл бұрын

Thats a weird looking parking brake...

@RockerFriendly 5 жыл бұрын

I didn't see this guy add anti seize or spark plug boot lube. Keeping mechanics in business by causing future problems, huh?

@patrickhuntoon534 3 жыл бұрын

Don’t Put anitseise on Spark Plugs anymore makes a Mess Ngk recommends to Not use anitseize

@patrickhuntoon534 4 жыл бұрын

You Dont Gap Iridium Plugs because it will Ruin the Tip!!!

@mikehendrix6558 2 жыл бұрын

That thing is going to be new by the time yall finish

@mariebrevard93 5 жыл бұрын

How can I remove the dirt and debris without compressed air?

@sissorsister83 5 жыл бұрын

Compressed air in a can could work.

@DustinOuterSanctum 5 жыл бұрын

Allllllmost forgot to blow out that debris... :) I would get a can of compressed air in the stationary section at WalMart.

@bradenanderson5087 5 жыл бұрын

Use a can of duster, or a small attachment for a household vacum (you could get creative and duct tape a funnel or smaller tube to the vacuum hose for the right application).

@GetRealBaby 5 жыл бұрын

Good question. Try using a vacuum if you have a small enough extension to get into the hole.

@nevakainindustries4350 4 жыл бұрын

Take the valve cover off and replace the gasket. If you are doing plugs, you should be doing these as well.

@notsethrogen_4029 5 жыл бұрын

Why does it say “How to Replace Parking Brake Cable”? When this is just Spark Plugs.

@nevakainindustries4350 4 жыл бұрын

Honestly mate, I can't believe you would even waste your time replacing these plugs without the valve cover gasket. When I changed mine it came out in 15 pieces. No wonder it was leaking. I have a Nov 04 and it has been leaking since 2011. I finally fixed it, replaced plugs, leads, gave it a degrease. Trickle fed the battery over 36 hours, done wheel bearings, engine mounts, and some other bits and pieces. How much do you think it would sell for? Bearing in mind I charge $40 an hour cash in hand and spent 12 hours on it plus parts.

@nevakainindustries4350 4 жыл бұрын

$AUD58 for valve cover gasket. 9 x cans of super cheap auto degreaser at $3 a can, AUD$38 trade for set of Bosch Iridium Plugs, $75 trade for a set of Bosch Spark Plug Leads, $75 trade for Bendix Pads, Machined Rotors myself, 26.5mm meat left on after machining. much more done. Still needs aircon to be looked at, but I am not going down that road, I have a roadworthy and that is all I need.

@bangyahead1 4 жыл бұрын

Blowing the crap off the valve cover didnt occur to him until spark plug #4.

@1AAuto 4 жыл бұрын

+bangyahead1 Thanks for checking us out! 1AAuto.com

@rockhellien 3 ай бұрын

I'm guessing a tourque wrench isn't 100% necessarily but the guy has to make tool sales quotas

@mikehendrix6558 2 жыл бұрын

You didn't blow #2

@mikehendrix6558 2 жыл бұрын

You al.ost forgot #2. Lol

@scottykilmer3920 2 жыл бұрын

oh mann come onn these engines calls ford a good copper plugs, not a shitty platinum or iridium! Use copper plugs people, otherwise you will get performance loss!