If you like this video please please subscribe. Thank ! Fanpage : / mr-old-100194225154263 instagram : / mrold_tube #mrold #mroldrepair #Mroldfix
Пікірлер: 18
@TRT_WEB Жыл бұрын
good, thanks
@xgenhan Жыл бұрын
excelent what is the name of the machine to weld the battery? thanks
@Mr_Old Жыл бұрын
₫ 716,331 30% Off | BIFRC DH20 Mini Spot Welding Machine Adjustable 9 Gears With Quick Release Pen Nickel Plate for DIY 18650 Battery Welder Spot We a.aliexpress.com/_m0QwUdw
@angelisone Жыл бұрын
Mr Old & anyone know the TPMS' battery size of a 2011 Hyundai Tucson USA model?
@OliverJobson Жыл бұрын
This works for ford sensors with the following codes: 2036832 EV6T-1A150-DB EV6T-1A180-DB EV6T-1A180-DC, 2036832,2318530 (not an exclusive list).
@blueapple4044 Жыл бұрын
Good job however you used a regular battery and the one in the original is a high-temperature battery.
@lohchenyeh77479 ай бұрын
What gum using bro?
@user-uy3wp5dn2q2 ай бұрын
أنا محتاج بلف وحساس ذاي ده
@Limas5147 ай бұрын
is the silicone required?
@CalPil0t7 ай бұрын
Just something to hold that cap on after the battery change. Superglue would work, but might be harder to remove in a few years when next battery replacement is due. I just had mine replaced when one failed. Was getting new tires and the remainder were weak. Still cost $50 each installed and that was steeply discounted. I kept the old ones and may change the batteries and use them next go around.
@musiccentral1977 Жыл бұрын
What is the number on the original battery? I have the same TPMS sensor and I want to order the batteries before I open the sensors to replace the batteries.
@MikeMike-gw6vl Жыл бұрын
It is likely cr 2032 battery in most of these sensors. But I just opened one of mine and ordered batteries but found out that a battery cr2450 has the same voltage but more capacity so would last longer ,which is what you really need in order to do the job once and have a peace of mind for even longer that when it was new/original. Isn't it ? Hope it helps
@CalPil0t7 ай бұрын
I just opened mine up yesterday. It has a Maxell CR2032HR in it. The HR suffix means high temperature rating (125° C for Maxell. A non HR Panasonic is listed to 85° C). Unless you are operating in a fairly high temperature area, the regular 2032 should stay within its operating range.And the Maxell data sheet publishes an acceleration spec. The voltage was down to just under 1/2 volt, and had failed about two months ago. I am going to clip in a 3 volt battery at my local tire store and see if it works again.
@graemeconnelly88498 ай бұрын
Is it not easier just to buy a new sensor
@davido34034 ай бұрын
No it is not. You don't just swap them and they magically work. You have to have the electronics to reprogram and activate a new sensor and you have to know how to do it. Put a new battery and its easy to get up and running. Or I wouldn't be watching this video.
@marijanmarijan1073Ай бұрын
heiss machen mi fön
@davidlevitanus962910 ай бұрын
Сволочи. Уже давно я купил эту систему и в датчиках давления тогда делали батарейную крышку. Отвинтил крышку и поменял батарею без всякого геморроя. Сейчас делают датчики одноразовые. Кончилась батарея - меняй всю систему на новую. Сторонние датчики не подойдут, надо прописывать в каждый датчик его ID адрес, а это ещё та головная боль.