This years award of most shake in a video goes to this guy
@yomamaisawhore2141 Жыл бұрын
Facts
@patchcs9 ай бұрын
Cellphones have come a long way with video stabilization
@cliby259 ай бұрын
Lol I said the same
@Aristotle2000 Жыл бұрын
I only threw up 3x while watching this video.
@cva6523 Жыл бұрын
Dude!! You saved me! I was trying to compress it, and I thought it was ceased until I saw your video. I can't thank you enough. Fyi needle nose plyers work just as well. Thanks man!!!
@toolscarswithkris5 ай бұрын
Yeah that's how I normally do it. But they were slipping from the pressure in the lines
@fabiangalvez96783 ай бұрын
same here lol😂
@masteringalltrades81442 ай бұрын
Bro thank you so much I'm 30 minutes in looking through videos and found you thank God.
@Straight_to_dust Жыл бұрын
He got Parkinson’s but he knows what to do. Thanks m8
@thegman4759 Жыл бұрын
Lmfao 😂😂😂
@dewilliams2012 Жыл бұрын
Newer models that have electronic parking brakes and you need a scan tool put brake system into service mode to unlock rear brake calipers.
@IDK-vs1mg Жыл бұрын
I did two rear E-brake jobs last week, didn't use a scan tool even though I have access to multiple manufacturers factory scan tool software. I used a lithium jumpstarter.
@liammitchell305610 ай бұрын
I did my rears on 2015 audi a3 with ebrake, and I didn't use anything like that at all. It all functions properly still too
@AmiriAutosMM7 ай бұрын
You need 12v to attach to the sensor and get it to move either way by switching the positive and ground
@YuckFou0x0FFFF2 ай бұрын
@@IDK-vs1mgThat's how you f around and end up paying for the repair 😂
@scotimottiАй бұрын
Great camera work
@toolscarswithkrisАй бұрын
Means alot to me
@ferndog1461 Жыл бұрын
Put some silicone lube on the seal so it doesn't twist.
@milosmihailovic18772 ай бұрын
Hvala brate, spasio si me ❤
@CrIMiN8l8 ай бұрын
Is it clockwise both sides
@toolscarswithkris5 ай бұрын
Yes the same direction for both sides
@messynate21 күн бұрын
If your handbrake is on, is that ok
@manuelquintanilla51159 ай бұрын
I did open the break fluid dispenser and then push it with the clamp it did so easy like the front ones
@nesc393 ай бұрын
How come you were shivering?
@Zesty_Skeeter_69 Жыл бұрын
Figured this out the way on my Malibu tore the fukin caliper and brake fluid started to leak, so I then had to not only replace the brakes but I had to drain the brake fluid to make sure to there was no air pockets and tbh I should’ve done that sooner but I also had to replace the whole damn caliper as well Bcs it was busted needles to say won’t be doin that again but that tool is a life saver not sure why only the rear ones require it tho and not the front
@ferndog1461 Жыл бұрын
Spray light cost of WD40 or dab of silicon brake grease so the rubber piston seal doesn't twist & fail. Been there, done that.
@Sr82. Жыл бұрын
I thinknthey twist because thats how the handbrake operates and it only works the rear . I have seen them on the fronts tho maby they have handbrake on the front wheels
@stevegrim Жыл бұрын
Could you shake the camera a bit more, I could still sort of see what was happening.
@toolscarswithkris5 ай бұрын
Sure thing I gotcha on the next one
@bindingle8 ай бұрын
Bro you just saved my life I was trying to c clamp my 2013 rear ends in and I broke a c clamp before looking I was like wait has to be anything different to it wow I love you
@toolscarswithkris5 ай бұрын
Lol it's okay I did the same thing my first time. I even thought I had a old clamp, brought a new one ,and broke it as well!!
@joegarrett81669 ай бұрын
What if it won’t turn. Is there another step ? Like compressing ebrake of something you left out?
@jeffnist9921 Жыл бұрын
I remember when that tool first came out on the Tool Trucks, I've literally owned one for 35/40 years....used it maybe 3 times. We called it a Rubiks cube.
@KingsMovement249 ай бұрын
This helped me just now
@kmbriggs26936 ай бұрын
That is also how you cause a low brake pedal due to rolling one.of the master cylender piston cups over .not to mention setting a abs code due to dirty fluid with particles that clog isolation valves in abs controll valve body. Never force fluid backwards through system.open bleeder.
@Diegoooo239 Жыл бұрын
Why people complaining how hard is it … you get the piston cube tool match the slots put it on the ratchet and twist into your piston💀 boom
@tracyvian36622 ай бұрын
Very helpful
@edgarescandar39446 ай бұрын
Please explain if the turning with the tool is screwing it in or just allowing it to be pushed in. So is it a turn and push or turn and turn. About how many turns, a few or a few dozen? Thank you.
@toolscarswithkris5 ай бұрын
You have to push and turn. It doesn't have a screw it just allows the pressure to release so so sometimes it takes more turns than others
@edgarescandar39445 ай бұрын
@@toolscarswithkris I appreciate your very late reply. with many important details missing in your video, it costs us about $1,000 to have it towed and worked on the shop with all our parts. please stay with your day job and stop making these critical inaccurate videos.
@toolscarswithkris5 ай бұрын
That's funny because if you listen I said what way to turn it. Working on cars is my job... You paid 1000$ because it's not your job.... Probably safer for that way for everyone else around you to have a professional do it.
@nineteen70six8 ай бұрын
Wow, your camera skills are awesome 😂
@toolscarswithkris3 жыл бұрын
Very bad video!! My apologies. I was trying to work with one hand and record with the other!
@lisaj2892 Жыл бұрын
You where still able to show what you where doing.. I got it the first time! 👌🏽
@IanMorison-fg3nc9 ай бұрын
All you need is a tool with a couple of prongs to fit the slots and it turns easily
@चेतन_महाराष्ट्र17 күн бұрын
You need to ask someone to hold the camera while you work.
@gregiles9086 ай бұрын
Can you do a "How to film a shot properly" video too please?
@toolscarswithkris5 ай бұрын
That may be to difficult
@anwarabdullah92783 ай бұрын
Shaking video, make me headache.. 😬😬
@wardwrenching Жыл бұрын
Good info!
@michaelschweizer93054 ай бұрын
Your camera is shaking. Hello?!
@toolscarswithkris4 ай бұрын
Or.... Maybe your eyes aren't shaking at the right speed.
@AprilNorwood-bq3fp Жыл бұрын
What if you don’t have a weird tool? How do you do it with the needle nose pipers?
@toolscarswithkris5 ай бұрын
You can just put them in the grooves and twist and apply pressure the same way. Just be careful
@YUFlysofast Жыл бұрын
These infuriated me on my deville. Had to push so hard and the cube I ahead was ass idk. Got it done tho😊
@scratchoffkinggetmoney95579 ай бұрын
C clamp is all u need But u got me Real Dizzy 😵
@loganwork70248 ай бұрын
C clamp won't work on a rear caliper with the spring loaded parking brake. They need to be twisted into place. I tried using a c clamp and vise grips to twist but messed up the caliper
@toolscarswithkris5 ай бұрын
Exactly
@toolscarswithkris5 ай бұрын
Exactly I learned the hard way myself the first time I ever did this many years ago. Broke 2 different c clamps in the process.
@oogabooga30702 жыл бұрын
what weird too like this is that called
@toolscarswithkris Жыл бұрын
found it autozone
@amberholloway21929 ай бұрын
Do u have to do tht the places i go to dont do to
@toolscarswithkris5 ай бұрын
Some are different. I only have to do this on the rear not the front with my car
@stevenm31415 ай бұрын
In the options on the camera, turn on stabilize! And get a tripod!
@hoeacio15 күн бұрын
Ahhhhh!!! EARTHQUAKE 😮!!! RUN FOR COVER 😅
@adansalmeron18802 ай бұрын
Dude, next time get a camera tripod or holder😒
@jcadult101 Жыл бұрын
Good to see Michael J Fox still making videos
@codylewis3929 ай бұрын
I used a c clamp and it worked great.
@jakemingus58819 ай бұрын
You can’t with this piston
@Splittingatoms219 ай бұрын
Not on this one Einstein
@royrobinette78335 ай бұрын
Your a lier.
@2stepsforward3stepsback654 ай бұрын
That ain't no newer car u need a c clamp n old brake pad just did an 09 traverse about a hr ago n now it drives fine
@frankdad0n10 Жыл бұрын
What’s the name of th are tool
@toolscarswithkris Жыл бұрын
not sure. i got it from autozone years ago
@nastynick7125 Жыл бұрын
rear brake piston compressor
@c.hes4388 Жыл бұрын
Link for the adapter
@toolscarswithkris5 ай бұрын
Autozone
@abdil2910010 ай бұрын
Good to know
@AprilNorwood-bq3fp Жыл бұрын
Y’all are all rude . Thank you very much. I just need to know how to do it with the pipers?
@toolscarswithkris5 ай бұрын
You can just put needle noses in the groove and twist just be careful not to let the tip slip and rip the rubber bushing around the piston
@AmiriAutosMM7 ай бұрын
Rest in peace the brake hose 😂
@davidgray92928 ай бұрын
This didn't work for me!
@mitchellcox1912 Жыл бұрын
the first time I saw this type of piston was on a 2000 jetta. I freaked out and my neighbor said that's what you will find these days. back then we called this tool a Rubix Cube like the toy. I hate the piston design and would prefer the engineers that dreamed up this be burned alive.
@stashmark71053 ай бұрын
Shake that camera just a little bit more R and it feels like im in your mudder off road with a full kegger in the carry bed with suzy at the wheel.
@JDMHaze10 ай бұрын
use a airchizzle
@user-bz8uc2cp2x8 ай бұрын
Did you film this during an earth quake?
@toolscarswithkris5 ай бұрын
I did. It was pretty cool!
@RobertDodd-Rockingham Жыл бұрын
Can anyone name that tool? Im running into the same issue.
@toolscarswithkris5 ай бұрын
Search like bake piston reset tool. I found this one at AutoZone years ago
@henryjohntobin19 ай бұрын
I'm dizzy!
@jacknguyen3233 Жыл бұрын
Dude forgot he was recording.
@bennycrypto3428 Жыл бұрын
Good effort hard to make video and spin tool with 1 hand
@toolscarswithkris5 ай бұрын
Thank you for understanding lol there are so many hatters it's funny
@cesarsanchez938510 ай бұрын
Ok you know how to do that . Can you show me how to hold the camera still….. Iiiiii’m diiiiiiiiiizyyyy😢!!!!!!
@freddytait77266 ай бұрын
Redo video. Must do better can do better 😢
@elebeu9 ай бұрын
Wait until the earthquake and aftershocks subside before filming your how to videos.
@toolscarswithkris5 ай бұрын
I like the challenge!
@secretsquirrel6124 Жыл бұрын
Tripod
@Reyzar. Жыл бұрын
Ty for video ❤
@toolscarswithkris Жыл бұрын
My pleasure!
@officialobama3547 Жыл бұрын
Its hard to be a mechanic when you also have parkinson
@toolscarswithkris5 ай бұрын
Very hard but we get it done
@robbyrodriguez78137 ай бұрын
I need Dramamine to watch this. 🤢🤮
@bobmac9070 Жыл бұрын
What’s the matter with you. Why would you make such a horrible video !!! Just terrible bouncing all over the place did you watch it before you posted maybe you should. 😤😡
@yomamaisawhore2141 Жыл бұрын
He's a meatball
@toolscarswithkris5 ай бұрын
You're a very kind person. Love you too buddy.
@user-sq1nd6km5u5 ай бұрын
a blank screen would have been better
@toolscarswithkris5 ай бұрын
How kind. Thank you so much for your input!
@ogc13129 ай бұрын
Man with parkinsons pushes back brake caliper piston
@toolscarswithkris5 ай бұрын
How you know I don't have a disability? Your so sweet
@yomamaisawhore2141 Жыл бұрын
This is how you miss a video up when you shake the camera
@charliefarrell48882 ай бұрын
Michael J Fox shoot this video? Asking for Larry David.