how to rub up basecoat! Hp12

Рет қаралды 20,188

Rendervate Hub - The Rendering Channel

2 жыл бұрын

quick video on rubbing up the base coat with a diamond float!
Interested in our services? Get in touch!
Email: info@rendervate.co.uk
Phone: 07553 618156
Website: www.rendervate.co.uk
#plastering #rendervateleeds
Follow my social pages:
Facebook: / rendervateleeds
LinkedIn: / joel-cooke-a52690219
Instagram: / rendervateleeds
Check out another one of my videos: • How i use my REFINA Spat
Watch through one of my playlists:
• Wall Rendering - What ...

Пікірлер: 49

@Joe-jv5mm Ай бұрын

Your Attention to detail, Great for the Novices 👍

@markneeson7162 2 жыл бұрын

Brilliant video as usual Joel, your enthusiasm for plastering is infectious, I can't wait till tomorrow to get some sand/cement on.👌👌👊

@Rendervate 2 жыл бұрын

Thanks mark love this game like you mate 👊🏾

@Trowel1892 2 жыл бұрын

Great video very informative! Keep them coming

@bernardrevill9547 7 ай бұрын

Your videos are more informative than any of the others. Thanks for all the advice.

@Rendervate 7 ай бұрын

Thanks mate glad you enjoyed!

@MrSamuelatkinson1 7 ай бұрын

Ace video cheers mate 👍

@Bets463 6 ай бұрын

Good Video Joel

@johnjameson6191 Жыл бұрын

Nice Vid again Mt

@leonardolucart3711 Жыл бұрын

insane vidio

@funnymarco1 2 жыл бұрын

Another great vid, much prefer GP Mortar (K Mix) for a nice smooth floated finish, one of the reasons is it`s cheaper than HP12 and I`m a tight arse.

@steffanthomas8734 2 жыл бұрын

Great video joel I've got a job to do on ewi the customer wants its smooth I've done alot of monocuche render but thinking of doing thin coat what would u recommend??

@kaimichael5444 2 жыл бұрын

Good video again. I use ki7 normally and baumit kzp. I usually spray mesh in morning then top out in afternoon. Then I ibarr next day. Do u ever Barr ocr or use this method all time Joe. Nice to know how other guys finish b4 texture

@Rendervate 2 жыл бұрын

Hello mate, yeah I mainly do this finish, but I will be doing your way in the next project I have which is a big gable end. I usually have my power float with me to, which takes the shoulder work out of it!

@blakeevans2963 2 жыл бұрын

Aup mate. At what point do you start using the diamond float??? How you know whether its to wet other than you drag it off the wall

@lloyds053 Жыл бұрын

Booked into get get my silicone render done end of November, would you say it's ok to do it this time of year mate

@edieldervishi9587 2 жыл бұрын

how long do you need to wait to achieve this, as we just spat it flat, but would prefer to float it thanks

@brad8526 Жыл бұрын

Can you use a sponge float to rub up instead of the diamond float ?

@jamiec4108 Жыл бұрын

When using refina power float on hp12 what attachment you using Sponge float or black plastic 1?

@rbbuildsandleisure1470 2 жыл бұрын

I saw one of the floats in Bell Tools Bristol the other day

@Rendervate 2 жыл бұрын

Bit far for me that mucker hahaha

@DannyArbuckle 2 жыл бұрын

Which one........horfield or Bedminster?

@rbbuildsandleisure1470 2 жыл бұрын

@@DannyArbuckle it was Bedminster but that was ages ago

@hoopy8 2 жыл бұрын

Great video. What are you using to flatten in that tight coat?

@hoopy8 2 жыл бұрын

Still not tried one of those diamond floats but definitely going to buy one having seen this video 👍

@LJHPlastering 11 ай бұрын

Alright mate people have asked me to use Weber base coat as a top coat what is your thought on it ?

@nathanjames3536 2 жыл бұрын

Another top video and advice top man 👍👍👍 Just one question tho about hp12 can you finish it and paint it and not put the thin coat on?? Nathan

@Rendervate 2 жыл бұрын

Thanks mate, yes you can finish it smooth, so do this process then just sponge finish it, leaves it nice! We do this because it’s getting texture. 👍🏽

@nathanjames3536 2 жыл бұрын

@@Rendervate that's great thankyou I'm new to the spray render been set in my ways using sand and cement but been using parex gm recently and been asked to do a fine down finish but not in sand and cement so this may be the answer Nathan

@tonyc1167 Жыл бұрын

Joel can you k rend base coat brick work if its clean? If you have to primer can you use sbr? Or do a slurry coat? Tc primer well expensive, i only need to render 5 sqaure meter

@Rendervate Жыл бұрын

it depends what the bricks are like mate, if they are rough I would just clean them down with water and go on to it. if smooth defo need a primer on them mate.

@ernieforrest7218 Жыл бұрын

Well unless the base coat will be the final coat, it certainly isnt necessary to be criticle on finishing it with the float. Just knock down the trowel welts is sufficient enough.

@mattptn5279 2 жыл бұрын

Why do you not worry about bridging at the dpc

@Rendervate 2 жыл бұрын

yeah i do worry about bridging mate, this is above dpc level, bridging is not good!

@vernonalexis704 2 жыл бұрын

Ain't there a machine for that circular motion to make it quicker

@mitsubisher5829 2 ай бұрын

Is that a finished topcoat

@mitsubisher5829 2 ай бұрын

A finish or are you going over it again ?

@mitsubisher5829 2 ай бұрын

Take it back I managed to watch it till the end

@lea-rw5cb 2 жыл бұрын

Hp12 is horrible to rub up I prefer krend basecoat

@Rendervate 2 жыл бұрын

Hp12 is krend bruva

@lea-rw5cb 2 жыл бұрын

Ypu hqve krend basecoat and krend hp12, i did it for almost 20 yrs we never used hp12 for topping off scratch as its sticky only used it for scrimming really, i left the trqde 5yrs ago and retrained as a engineer but do miss it expecially in summer lol 👍 oh and if you have never done structherm you havent lived lol

@lmilne4859 Жыл бұрын

HP12 great stuff 1 best on the market

@stevenalbert8552 2 жыл бұрын

hp12 is as rough as arseholes like all k-rend...mad man using it these days...poo,not doubting you know whats what...im a renderer of a lot of years....k-rend is dog..horrible gear, get on the fassas,the Webbers,the parex..even vimark....k -rend awful stuff,dated and a pile of shite that fades in the sun..no uv value, brittle and an awful product

@Rendervate 2 жыл бұрын

wow you dont like the krend haha, na its not the worse on the market, they are a leader in the market you dont get there being rubbish mate, ive used a lot of products, Fassa i like, Weber is good, the best on the market for me is Baumit and Ecorend, for numerous reasons.

@stevenalbert8552 2 жыл бұрын

Trust me mate..they certainly ain’t the leader in the market,they was the first in the market branded here,so why everyone calls it k-rend when it’s really monocouche,it drives the french mad,a shit product in Ireland taking the thunder but that’s not either here or there,i was doing back in the day when it was called ..crem-rend,first over here,so we know a fair bit…k-rend won’t endorse you mate,it’s not going to happen…shop about,even cpi not bad,..prb at one stop…but don’t mug yourself with k-rend 😂😂😂

@G2020- 2 жыл бұрын

K-rend gets a bad rep mostly for its k1 silicone range. The basecoats are the best on the market

@lmilne4859 Жыл бұрын

Most negative is because they can’t use it.

@stevenalbert8552 Жыл бұрын

@@lmilne4859 no…it’s shit