How to save your bicycle ! Bike front hub complete service and overhaul

Рет қаралды 117,008

Күн бұрын

Hello my dear cycling viewers!
Today in this video tutorial I will touch on a topic such as timely maintenance of a bicycle hub.
This is a very important lesson. You will be able to see clearly what to look for and what to do to make your bike last as long as possible!
I'll show you how to completely service and overhaul a bicycle front hub.
By examining the bicycle hub parts in great detail, we can find small points on the cone where the bicycle wheel bearing balls touch.
It is very important to replace this cone. This will save your bike!
We will also replace the grease inside the hub.
For example, we will use the popular Shimano HB-TX505 bicycle hub.
Have fun watching my dear friends!
Verbal-free video showcasing mechanical sounds. Understandable across languages; an international DIY video.
If you're passionate about cycling, this video is for you.
00:00 How to save your bicycle.
00:17 How many tools are needed to service a bicycle hub.
00:33 How to clean the outside of a bicycle hub.
00:48 How to disassemble the front hub of a bicycle wheel.
01:46 How to remove the bearing balls of a bicycle wheel hub.
02:10 How to dismantle a bicycle hub.
03:10 How to service bike front hub.
04:02 How to properly wash a bicycle hub.
07:00 What can affect the speed of the bike.
07:17 How to replace the cone hub of a bicycle.
08:36 How to replace ball bearings in a bicycle hub.
09:31 How to lubricate bearings in a bicycle wheel hub.
10:05 How to assemble a bicycle wheel hub.
11:58 How to adjust the front hub of a bicycle wheel.
Thank you for your comment! 😍
If you liked my videos ❤️,
support the channel financially 💰🙏.
Use the "Membership" / "Sponsor" function on KZfaq ✊😘

Пікірлер: 212

@NiceBikeService 2 ай бұрын

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤ it will help the development of the channel! 📈

@andi1831 2 ай бұрын

It's so satisfying watching the grease get socked in to the bearing.

@NiceBikeService 2 ай бұрын

Thank you for your feedback! 😘

@Cycle-Tourer 2 ай бұрын

Great photography job. Excellent close-ups.

@NiceBikeService 2 ай бұрын

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

@antoniomora8487 Ай бұрын

Yo tambien usó todos esos utensilios como el palillo de dientes y el potecito para echarle los rodamientos al eje y los potes de plástico para guardar rodamientos y tuercas bujes y demás cachivaches a la hora de hacerle mantenimiento a mis bicicletas 🚲🚲🚲 Gracias por compartir tus experiencias con el resto del mundo saludos desde Cúcuta Colombia 🇨🇴👍🚴🚴

@NiceBikeService Ай бұрын

Gracias por sus comentarios. Nos complace darle la bienvenida a nuestro canal desde el otro hemisferio de Ucrania 😽🚲🇺🇦

@Jim-be8sj 2 ай бұрын

Fantastic technique for installing the bearings and them packing with grease. I'll need to learn how to do it like that. Thanks for sharing this fine video!

@NiceBikeService 2 ай бұрын

glad to be of service! thanks for your feedback 😘

@yasinsheikh3 2 ай бұрын

Every video on this channel is mind blowing 👍

@NiceBikeService 2 ай бұрын

Thank you! We try.)

@RS-93551 2 ай бұрын

no talking, just working. thx. sub and thumbs up.

@NiceBikeService 2 ай бұрын

glad to be of service! thanks for your feedback 😘

@adamus572g4 2 ай бұрын

Jak zwykle świetny poradnik. Ja akurat mam problem z tylna piastą.

@NiceBikeService 2 ай бұрын

Dziękujemy za opinię!!!!

@GOWESMALANG 2 ай бұрын

Perawatan sepeda yang sempurna.. terbaik kawan👍👍

@NiceBikeService 2 ай бұрын

Terima kasih atas komentar Anda! 😍 jika Anda menyukai video ini, bagikan video ini dengan teman-teman Anda ❤️ itu akan membantu perkembangan saluran ini! 📈

@jaredlee2819 Ай бұрын

잘 보고있습니다. 감사합니다 많은 도움이 됩니다 자가 정비할때도요 제 자전거도 분해 후 세척도 해야되겠네요

@johnbelwell2461 4 күн бұрын

I suggest that you use more grease and tightly pack the washer with it, might have a little more friction but grease keeps water out as it's not a sealed bearing, so the first time some water gets in the side effects start appearing soon.

@NiceBikeService 4 күн бұрын

Thank you for your advice. There are different opinions about the amount of grease, if there is too much, it will come out and start sticking to dust and sand

@MedSid-gc4un 2 ай бұрын

Ya3tik et saha c'est professionnel 👍👌

@NiceBikeService 2 ай бұрын

شكرا لك على تعليقك

@serhiizabobonin1016 2 ай бұрын

Hello my dear Nice Bike Sservice. I'm affraid of such hubs. Can't decide where to stop screwing hub. The wheel sounds beatiful, well tightened spokes.

@NiceBikeService 2 ай бұрын

Reedy welcomes you to our channel. You can play around a bit and catch the moment when the axle no longer has play but rotates easily

@EdwardMountainBike 2 ай бұрын

cara, que video perfeito, relaxa muito esses tipos de video, apenas os sons da bicicleta, parabens!😀

@NiceBikeService 2 ай бұрын

Obrigado pelo teu comentário! 😍 se gostaste deste vídeo, partilhe este vídeo com os seus amigos ❤️ isso ajudará no desenvolvimento do canal! 📈

@usualsuspectrider1367 Ай бұрын

LOOOOOOOOOOOL encore un tuto pour les braves gens !

@mikefoster3901 2 ай бұрын

Electric toothbrush is a novel idea Must try it some day 👍

@NiceBikeService 2 ай бұрын

Yeah. I came up with that idea by accident. What do you clean with?

@blackIwaterIpark 2 ай бұрын

Świetny pomysł na to, jak stworzyć wartościowe ''nieme kino''. 👍 😊 Przy okazji odkryłem, że takie filmy mają uniwersalny wymiar: cały świat może je zrozumieć - od Grenlandii aż po Przylądek Dobrej Nadziei. PS. Masz jakiś sprawdzony patent na to, jak w prosty sposób napełnić strzykawkę smarem??

@NiceBikeService 2 ай бұрын

❤️❤️❤️ it's a secret)

@Cbych 29 күн бұрын

Możesz jedną strzykawkę obciąć na końcu (całe dno) o mniejszej średnicy i tak napełniać tą docelową coś jak pipeta.

@blackIwaterIpark 29 күн бұрын

@@Cbych : OK, niezły pomysł. 👍

@o78rus91 3 сағат бұрын

Красиво , что тут скажешь)

@Misselthwaitefullcircle Ай бұрын

Great work and great techniques. Keep uo the good work 😊

@NiceBikeService Күн бұрын

Thank you for your feedback! 😘

@robertmcfadyen9156 2 ай бұрын

You can polish out the marks on an angular contact bearing nut if you cannot find the exact replacement . Useful for older models .

@NiceBikeService 2 ай бұрын

thanks for the advice ! 😘

@robertmcfadyen9156 2 ай бұрын

@@NiceBikeService One thing that I will shortly bring up with "Bike Shed Boy" , from the United Kingdom is how it feels to lace wheels with progressing osteoarthritis and finger joint spurs . I am only in my 50's . Do you have any opinion on this ? A man broke my left hand and wrist two years ago when I bad a type 2 diabetes low blood sugar seizure similar to an epileptic fit in front of him at his home . I also had one after a very long bicycle ride as I couldn't stop riding easily /safely . The man that broke my bones is demanding a free bicycle and isn't happy for me to build him a red GT Avalanche custom build in his frame size . Frames in his size are hard to find at a reasonable price at the moment . The man won't pick from the collection of good mtb frames that I have in my stock inventory . He also wants a rear pannier rack to use as a pseudo mud guard in wet weather .

@robertmcfadyen9156 2 ай бұрын

@@NiceBikeService I am , on a more positive note building a blue and yellow GIANT Iguana 26'er for my church minister's son Calvin . I hope that he appreciates the hard work as I complete it by this coming Saturday . I will give it to him on Sunday after the church meeting . Calvin loves surfing as well and I can take him on a social bicycle ride once a month with my TREK custom build 26'er mtb . She is very smooth to ride and can be seen at Fulcher's Cyclery , Panania , Australia on Google images .

@user-xw2cu1dn1y 2 ай бұрын

good job

@NiceBikeService 2 ай бұрын

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

@gabormolnar6126 2 ай бұрын

Omg man i did not know that those round caps over the balls can be removed :(((( ty!

@NiceBikeService 2 ай бұрын

you mean the dust covers?

@gabormolnar6126 2 ай бұрын

@@NiceBikeService yes! Haha

@steelisreal4313 2 ай бұрын

Be careful and use a wider tool if remove. A narrow tool will damage them and deform.@@gabormolnar6126

@RonnieSTH 2 ай бұрын

Pls do wheel lacing video ty!!!❤❤❤❤

@NiceBikeService 2 ай бұрын

will definitely do it!!!

@drkemankesh 2 ай бұрын

Hey! Nice video again! Congrats! I have a question. I have some trouble. 12:25 at this point, i cant easily enought tighten the screws. One time after aaaaa little tighten it tighten more and doesnt turn freely or if i loosen aaaa little it loosens more than i want and having a little space on hub. Is there no easy tactic or tips and tricks about this?

@NiceBikeService 2 ай бұрын

Thank you for watching and commenting. Try unscrewing the wrench by the cone, so that it moves with the outer nut just a little bit, literally a quarter turn

@damianlotartaro9790 2 ай бұрын

También es más fácil lograr el ajuste con un tornillo de banco, o con solo un lado del eje montado en el cuadro y en el otro extremo realizar el ajuste fino

@sergiobauza957 2 ай бұрын

Hello friend... a question... what liquid do you use to clean... you clean the grease very well... greetings from Chile and thanks for your videos

@NiceBikeService 2 ай бұрын

Thanks for the review!)) fluids range from isopropyl to engine cleaner.

@Seafoxmccloud 2 ай бұрын

nice video but why cleaning the parts who going to trash ?

@NiceBikeService 2 ай бұрын

good question) to show, to teach the public how to do it.

@MrBianconeri90 Ай бұрын

You can not see how much they are used, if you don't wash them

@costelitobr1401 29 күн бұрын

Bom ensinamento tudo novo

@NiceBikeService 28 күн бұрын

Obrigado pelo vosso feedback! 😘

@michak3130 2 ай бұрын

woooow you use electric toothbrush. Nice method

@NiceBikeService 2 ай бұрын

Yes, very convenient, you can try it

@natanaeltzul1-248 2 ай бұрын

Amazing vid as to be expected from you! My only question would be what grease do you use? Iv seen many different types of grease but never one with a green shade like the one you use. I really want to know what brand you use and if theres any particular reason you prefer this grease. Sorry that everytime i comment i ask a question btw.

@NiceBikeService 2 ай бұрын

thanks for the question!) green smiazki, usually divinol and shimano.

@natanaeltzul1-248 2 ай бұрын

@@NiceBikeService thank you so much

@ahmadfouadassaf6856 2 ай бұрын

sehr gut

@NiceBikeService Ай бұрын

Vielen Dank für Ihren Kommentar! 😍 wenn dir dieses Video gefallen hat, teile dieses Video mit deinen Freunden ❤️ es wird die Entwicklung des Kanals unterstützen! 📈

@davidoh5299 Ай бұрын

대단하십니다. 위치가 어디이신가요

@NiceBikeService Ай бұрын

피드백을 보내주셔서 감사합니다. 워크샵은 우크라이나에 있습니다.

@philippepiette6293 2 ай бұрын

Bonjour, merci pour cette vidéo. Chez quel détaillant peut-on trouvé des billes et cônes ? Intéressé pour sauver une paire de roues. Merci pour me transmettre des liens. Merci

@NiceBikeService 2 ай бұрын

Félicitations. Nous commandons généralement ces pièces auprès de fournisseurs locaux. Je ne pense pas que ce soit un gros problème de les trouver dans les magasins en ligne locaux, ou dans les magasins européens comme Bikeinn, Bike24, Bikediscount et similaires.

@benderenbois 2 ай бұрын

im the 100th like !

@NiceBikeService 2 ай бұрын

👍🚲😸

@user-en3zk1rw7q Ай бұрын

Great video, can you let us know what grease you are using and how to get it in the syringe?

@Tag-Traeumer 19 сағат бұрын

A valid question. I dipped my syringe into the grease and pulled the plunger back, creating a vacuum. The grease (Motorex Bike Grease 310670) was only sucked into the syringe very slowly. I gave up after half an hour when the syringe was half full, that's enough.

@streglof 2 ай бұрын

Very satisfying! Where did you get this metal tray thing in which you clean all the parts, is it from the medical field perhaps?

@NiceBikeService 2 ай бұрын

Thank you for your comment. The tray is made of food grade stainless steel, we bought it from a company that sells equipment for kitchens and dining rooms

@streglof 2 ай бұрын

@@NiceBikeService Looks very handy. Thanks for your reply!

@philippejoseph8604 2 ай бұрын

Nice video. Water and dust entering those cups and cones hubs WITHOUT seals are just destroing them. "The" solution is to always clean the external part of the hubs each week in case of a duty bike and each time if it rains. When you service the internal of a hub WITH seals there is not such things. You could add in "the" or "a" method to set correctly the play when tihghtening the cups+counter nut. My one is to approach by hand the threaded cup+counter nut to feal if there is too much or not enough play then choose to tighten alternatively the cup to loosen or the counter nut to tihgten the play and I do this with the shaft secured in a vice for ease of interacting on the threade cup + counter nut. When you buy a cheap wheel the shaft is always too much tightened resulting in a quick destruction of the threaded cup. Balls are very rarely damaged as they are the most solid part. Cups inserted in the hub are also rarely damaged as they are bigger than the threaded ones. The parts that are suffering the most are the external threaded cups as they are with a smaller diameter ball race.

@NiceBikeService 2 ай бұрын

thanks for the advice ! 😘

@pierregastie-leroy4922 Ай бұрын

Nice, i started to restore this, but i don't find dust cap in spare parts, do you where it is possible to buy ?

@NiceBikeService Ай бұрын

Thank you for your comment. Such details are very hard to find. Try searching in large online stores like Bike24 or bike-discount. maybe you can find something at flea markets or on classifieds sites.

@pierregastie-leroy4922 Ай бұрын

@@NiceBikeService I begin to make drawings for a new fabrication...

@steelisreal4313 2 ай бұрын

I'd like to point out that it's best to use something wide when removing metal shields over the bearings. If using a narrow tool the more chance of marring and damaging the seals which are a pain to replace.

@NiceBikeService 2 ай бұрын

Thanks for the advice. How wide should it be?

@trekkeruss 2 ай бұрын

It is best to use a plastic tire lever. But in reality, you do not absolutely have to remove the cap. Spraying it with degreaser and using a cotton swab to clean inside and underneath the cap is usually enough.

@steelisreal4313 2 ай бұрын

@@trekkeruss I usually use a plastic tire lever as well. I do have a blind hole bearing puller as well that I will also use but it's pricey and for me was a total impulse purchase. My OCD basically requires me to remove the shield and clean it lol.

@precision1971 Ай бұрын

Great video. Well done. If you included some affiliate links for some of the tools and products you used it would be even better.

@NiceBikeService Ай бұрын

Thank you for your comment. We do not provide advertising links. Some things in the workshop have been around for many years or are homemade. You can ask the name of what you are interested in, we will try to answer

@precision1971 Ай бұрын

@@NiceBikeService Thanks for the reply. I was particularly interested in the green grease you used for the hub bearings.

@jack002tuber 2 ай бұрын

Cup and cone bearings. I think last time I had those it was about 25 years ago. I don't rebuild the sealed ones

@NiceBikeService 2 ай бұрын

Thank you for your comment. I understand that it is quite a painstaking and dirty job.

@jack002tuber 2 ай бұрын

@@NiceBikeService Not bad. Once you know how. Hardest part is to get the preload on the bearings right, tight, but not too tight

@michelsaint-germain97.1 2 ай бұрын

Bonjour!! Est-il possible de remplacer un moyeu avec fixation à vis par moyeu à fixation attache rapide sur un vtt?

@NiceBikeService 2 ай бұрын

Oui, bien sûr, c'est possible, il suffit de choisir le bon axe en largeur et en diamètre, et bien sûr, que les cônes sur le résda puissent être tordus.

@michelsaint-germain97.1 2 ай бұрын

@@NiceBikeService merci pour la réponse rapide. Je vais m’abonner à votre page car j’aime bien vos vidéos, elles sont très bien expliquées. Par contre, quelle est la réf de la graisse que vous injectez avec la seringue? 😁

@davidoh5299 20 күн бұрын

베어링 27.5인치 리어는 6.35mm 확인했는데 보통 26인치 리어는 몇 mm일까요? 일반적으로요

@NiceBikeService 2 күн бұрын

베어링 볼의 직경은 6.35mm 또는 1/4인치이며 휠 사이즈에 따라 달라지지 않습니다.

@ArafatulIslam-vv4ip 2 ай бұрын

Nyc things

@NiceBikeService 2 ай бұрын

Thank you for your comment!

@kostiantyn.hermash 2 ай бұрын

What is the thread type on shimano hub axle? Diameter and pinch.

@NiceBikeService 2 ай бұрын

The axle is usually supplied with an M9 thread (metric system, 9 mm in diameter)

@cyrilastro 2 ай бұрын

Bonjour, vous êtes d’où ? Je suis dans le 06 et je cherche désespérément des écrou connes pour les moyeu avant et arrière de mon fils mais pas simple à trouver. D’avance merci de votre retour

@NiceBikeService 2 ай бұрын

UA 💙💛

@user-gz7ls2qk2s 2 ай бұрын

Hola buenas buen video, me podrías decir de cuántos mm son las bolas gracias

@NiceBikeService 2 ай бұрын

Buenas tardes. Diámetro de la bola del buje delantero 3\16inch = 4.76mm

@user-gz7ls2qk2s 2 ай бұрын

Muchas gracias muy agradecido feliz fin de semana

@glen3509 2 ай бұрын

I have a rear Shimano XT parallax hub with a seized freehub body. Can this be fixed or maybe replaced? The hub is from 1998 or 99.

@NiceBikeService 2 ай бұрын

of course you can. here are some videos on the subject kzfaq.info/get/bejne/nbCkZpuBubTbc30.html kzfaq.info/get/bejne/gZmloqRex8fXcoU.html kzfaq.info/get/bejne/b9ddn6SUlc61l2g.html

@glen3509 2 ай бұрын

@@NiceBikeService Thanks🤘🤘

@glen3509 2 ай бұрын

I got these XT parallax hubs when I bought a barely used set of Mavic SUP 517 wheels. I only paid about 💰350.00🍁🤘🤘

@NiceBikeService 2 ай бұрын

❤️

@mdcoelho3652 2 ай бұрын

Qual o nome deste produto que voce usa para limpar as pecas?

@NiceBikeService 2 ай бұрын

gasolina e isopropil obrigado pelo teu comentário! Compartilhe esse vídeo com seus amigos, isso ajudará no desenvolvimento do canal! 📈😘

@mdcoelho3652 2 ай бұрын

@@NiceBikeService ok

@berofudomitori 2 ай бұрын

Would be great to see the names of liquids you used

@NiceBikeService 2 ай бұрын

Hello. When washing the balls, we used refined gasoline "galoshes", the closest analog of kerosene (camping) fuel. In the sprayer, an automotive engine cleaner, for lubrication, a thick calcium grease divinol

@berofudomitori 2 ай бұрын

@@NiceBikeService thanks for the answer)

@euzebiuszkarpacki3810 2 ай бұрын

Ciekawe ♥️

@NiceBikeService 2 ай бұрын

Dziękuję za komentarz! 😍 jeśli podobał Ci się ten film, udostępnij ten film swoim znajomym ❤️ pomoże to w rozwoju kanału! 📈

@euzebiuszkarpacki3810 2 ай бұрын

@@NiceBikeService jasne 🙋

@hishammudinhassan1996 26 күн бұрын

bahan apa yang anda gunakan semasa kerja cucian

@NiceBikeService 23 күн бұрын

Kami membasuh gris lama dengan petrol "kalosha" yang disucikan, analog terdekatnya ialah semangat putih, bahan api perkhemahan

@Wojtek404 Ай бұрын

What happens when the cones are not completely the same, with a very little difference. Is it bad?

@NiceBikeService Ай бұрын

You have one of these There are bushings with different right and left cones, possibly

@statom985 2 ай бұрын

Co było użyte do czyszczenia ? Benzyna ?

@NiceBikeService 2 ай бұрын

isopropil gasolina obrigado pelo teu comentário! Compartilhe esse vídeo com seus amigos, isso ajudará no desenvolvimento do canal! 📈😘

@anonymously241 2 ай бұрын

Where is your shop located my friend? 🚴‍♂️

@NiceBikeService 2 ай бұрын

Hello, my friend. Our workshop is located in Ukraine, Kyiv

@user-mw2zh8cv7n 2 ай бұрын

여기가 어디 입니까 가고 싶어요❤😊😢

@NiceBikeService 2 ай бұрын

아직 멀었습니다. 워크샵은 우크라이나에 있습니다.

@JL-od4wg Ай бұрын

7:50 Where u brought that cone nuts?

@NiceBikeService Ай бұрын

You can buy them in online bike shops. For the workshop, we bought them in bulk in our country

@ANTO4545N 2 ай бұрын

Hi what is the part number of those bearrings and the cone

@NiceBikeService 2 ай бұрын

I can't tell you that, I don't know.

@dashofawesome64 2 ай бұрын

Front Hub HB-TX505 bearing balls 3/16 size, 10 on each side. Y2A198020 Right Hand Lock Nut Unit Y2A198030 Left Hand Lock Nut Unit

@hudsoncivil 2 күн бұрын

Sempre coloquei 11 esferas 🤔🤷!

@NiceBikeService Күн бұрын

O número de bolas pode variar de modelo para modelo

@gusnuk68 2 ай бұрын

what camera do you use?

@NiceBikeService 2 ай бұрын

mi 12pro + lens

@gusnuk68 2 ай бұрын

@@NiceBikeService great, thank you

@user-cz1lp9yt7t 19 күн бұрын

Assuming you know how to take care of the bike, low-end ball bearing bikes are pretty good to ride.

@NiceBikeService 12 күн бұрын

This is true

@ironman1518. 2 ай бұрын

Very well done!! I disagree with cleaning the old used bearings. Why bother you are going to put in NEW bearings.

@NiceBikeService 2 ай бұрын

Thank you for your comment. The balls are still in good condition. It makes sense to change them, but together with the cones.

@MiguelPerez-ov3wx 2 ай бұрын

12:17 esta es la parte que mas miedo me da, porque si aplicas mucha fuerza el eje ejercera mucha presion y se partira o rompera la maza, pero si aplicas poca la maza al poco tiempo bailara.

@NiceBikeService 2 ай бұрын

hay que apretar bien la tuerca al cono, y luego ajustar el manguito girando un poco los dos juntos

@MiguelPerez-ov3wx 2 ай бұрын

@@NiceBikeService Gracias por contestar NiceBikeService tus videos entretienen mucho y contagia esa pasion por las bicicletas.

@ONEFORTY198 2 ай бұрын

玉押し調整は軸がガタつかないよう調整するとコーンとベアリングの節約になるでしょう。

@NiceBikeService 2 ай бұрын

ご意見ありがとうございました！😘

@juanpablograsso4355 2 ай бұрын

hola, yo instaló con rulemanes brindado y listo, mucho mejor con rulemanes

@NiceBikeService 2 ай бұрын

Aclárame, no entiendo lo que has instalado.

@johnjordan6032 Ай бұрын

Great stuff but there’s no way in hell a bunch of soil will be found in your hub on your ball bearings.😂😂😂

@NiceBikeService Ай бұрын

😺

@bobmarleyept 12 күн бұрын

what is the part number of the replaced cone nut?

@NiceBikeService 12 күн бұрын

If I'm not mistaken, the nut is M9

@bobmarleyept 12 күн бұрын

@@NiceBikeService thank you!

@makantahi3731 2 ай бұрын

you could have put a little more grease to start coming out and make a seal against the dust that had entered the bearing

@NiceBikeService 2 ай бұрын

possibly

@JavierVargasBG 2 ай бұрын

Con esa grasa es suficiente, la grasa es para lubricar no para evitar que entre el agua y el polvo, hay varios mecánicos que a fuerza quieren llenar todo de grasa, el peor caso los baleros del bottom bracket

@makantahi3731 2 ай бұрын

@@JavierVargasBG krivo, ti si vjerojatno kuhar po struci pa ne znaš šta čemu služi, mast u ovom slučaju ima funkciju podmazivanja, brtvljenja i pohranjivanja nečistoča koje uđu u ležaj a ući će ako nema brtve ili dovoljno masti koja bi stvorila prepreku za nečistoču, pogledaj na početku videa da je ležaj pun nečistoča jer u tvornici štede na masti , da su je stavili više ne bi bilo nečistoča a možda ni konus ne bi bio oštečen

@norbertnagy5514 Ай бұрын

@@JavierVargasBGyou dont need to grease sealed bottom bracket bearings but you should put grease at the contact points to keep water and dirt outside, yeah dirt sticks into the surface of the grease but it will cant go farther that that, so it may not even reach the outside of the bearing seals. If you outside bearing bb greasing as a type of sealing is a must.

@norbertnagy5514 Ай бұрын

@@JavierVargasBGyeah, there can be to much grease but thats really more important at high speed bearings, like engine powered machines. In those to much grease is similar when you try to run in water, its hard. It can cause the bearings to overheat and fail.

@blackIwaterIpark 2 ай бұрын

Dlaczego firma Shimano nie zastosuje patentu, aby wsadzić do takiej piasty zestawu łożysk tocznych (podwójnie zamkniętych)?

@NiceBikeService 2 ай бұрын

wszystko może się zdarzyć)))

@EfendyDarmawan 2 ай бұрын

Change into bearing

@NiceBikeService 2 ай бұрын

Thank you for your feedback! 😘

@labolilaboli5093 22 күн бұрын

Le liquide transparent s'il vous plaît ?????

@NiceBikeService Күн бұрын

isopropanol

@labolilaboli5093 Күн бұрын

@@NiceBikeService thank you

@Phothuya Ай бұрын

May I Know 5:35 liquid name please ?

@NiceBikeService Ай бұрын

This is a variant of refined gasoline, we call it "kalosha", so I understand that the analog is camping gasoline or coleman (camping) fuel

@neutrinoberilio3566 Ай бұрын

🚴😁👍

@NiceBikeService Күн бұрын

😀😻

@mutos82 2 ай бұрын

Dodalbym 1.sprawdzenie czy ośka jest prosta - ewentualne wygięcie niszczy miski w piaście. 2. Należy zwrócić uwagę aby użyte po raz drugi konusy, kulki i miski nie mieszać stronami. 3. Nie powinno się kasować luzu w taki sposób jak pokazałeś na filmie przez dokręcanie zestawu skontrowanej nakrętki-konus

@NiceBikeService 2 ай бұрын

nowe kulki! Dokręcanie jest prawidłowe, pozostawiono mikroluft. dzięki za komentarz. Pokaż mi jak to robisz.

@mutos82 2 ай бұрын

@@NiceBikeService sposób dokręcenia jest nieprawidłowy. Tak jak ty robisz może spowodować skrzywienie osi. Moment dokręcenia przykładasz na końcach osi - to jest nieprawidłowe np z powodów teoretycznych. Też tak kiedyś robiłem i sie dziwiłem dlaczego ośki się krzywią. Pozdrawiam.

@mateus.S_ 2 ай бұрын

Você é brasileiro?

@NiceBikeService 2 ай бұрын

💙💛 UA

@Rafael-zm5hq 2 ай бұрын

Cairan pembersih yg dipakai apa sih

@NiceBikeService 2 ай бұрын

Ini varian bensin olahan, kita sebut "kalosha", jadi saya paham analoginya adalah bensin camping atau bahan bakar coleman (camping)

@welchianachi7707 2 ай бұрын

Brak łożysk maszynowych w tak nowych piastach to zbrodnia.

@NiceBikeService 2 ай бұрын

Są tańsze i łatwiejsze w produkcji. Wytrzymują długo podczas codziennej jazdy

@morezawa86 2 ай бұрын

❤

@NiceBikeService 2 ай бұрын

😘❤️❤️❤️

@cheetocatto01 2 ай бұрын

These Shimano hubs been the bane of my existence in my road bike... Every single rainy ride needed cleaning and relube xD

@NiceBikeService 2 ай бұрын

They are not so delicate, they have some resistance to moisture.

@cheetocatto01 2 ай бұрын

@@NiceBikeServiceI live on the seaside, so rain came with a bit of salt and sand, 6 months in and it was seriously pitted. (and so were the freehub ones) I ended up swapping the hubs for cartridge ones. they tend to last a lot longer before salt water does a number on them. 😁 But i suppose the unsealed shimano ones do fine on drier situations. cheers!

@KarlosEPM 2 ай бұрын

@@cheetocatto01I use a lot more grease than shown here to do the trick. Grease serves three purposes: lubricate, prevent corrosion and seal the bearing. Also, a thick (ep3) grease designed for seaside/marine use (such as marine grease) works better than generic multi use (ep2) grease. Still probably not as resilient as good sealed cartridges, I agree. Cheers!

@akkyla2297 2 ай бұрын

Дуже слабенький захист від пилу та бруду в цих втулках, я б сказав, що його майже немає)

@NiceBikeService 2 ай бұрын

Є таке, все ж таки бюджетний варіант😺

@makantahi3731 2 ай бұрын

magnet again, ok you did not use it on new balls

@NiceBikeService 2 ай бұрын

Yeah. I love magnets.)

@donaldixon4036 2 ай бұрын

Talking a bit would help a Lot

@NiceBikeService 2 ай бұрын

Thank you for your comment. Some additional information will be in the subtitles. We shoot without words so that people from different countries can understand it

@brasileironeutro1998 2 ай бұрын

I clean it with gasoline, it's really worth it

@NiceBikeService 2 ай бұрын

Thank you for your comment. Indeed, gasoline copes well with grease contamination

@abdulharis9390 2 ай бұрын

Do tell the solutions you are using e.g.thinner/ petrol/ turpentine or whatever😂😂😂😂

@NiceBikeService 2 ай бұрын

Thank you for your advice. We will try to include the names of substances in subtitles😸

@velobike7 2 ай бұрын

Second tip: Make the video titles in 2 languages, English and Russian. other people will come to you then

@NiceBikeService 2 ай бұрын

in English, that's enough. the video has no words, it's intranational.

@norbertnagy5514 2 ай бұрын

@@NiceBikeServiceyeah but the title could still whats the video about and people can acquire the rest of the knowledge from the video.

@norbertnagy5514 2 ай бұрын

@@NiceBikeServicebtw good quality videos, especally good thats its 4k, keep up.

@mic790 Ай бұрын

@@norbertnagy5514и без названия по-русски все понятно. Отличное видео 👍 точно для себя делаешь)) иначе какие зубочистки)))?

@gracjanrok3994 2 ай бұрын

Moze filmik o wymienie łozysk maszynowych w piascie ??

@NiceBikeService 2 ай бұрын

opracowanie

@gracjanrok3994 Ай бұрын

Konus odkreca sie tylko z jednej strony, chyba ze jest uszkodzony lub os to wyniebiasz komplet... Po takim skreceniu kolo w hakach napewno bedzie krzywo osadzone

@NiceBikeService Ай бұрын

interesting comment 👍