I appreciate the input, I have watched multiple "how to" and for me it's about the time involved. The faster I process the motors the more profitable it can be so it out weighs the cost of the cutting wheels and copper dust. I actually use my band saw to cut the windings now and multi task the process. At the end of the day there is no right or wrong method its just a matter of completing the work safely and making some money! Happy scrapping. Appreciate the feedback 👍

I use a chop saw to cut the one end and I have a shroud setup which catches all the copper dust and then use a scissor clamp attached to log splitter

I saw someone make a two prong chipping hammer chisel on a chisel chipping hammer

Aki no Brasil retiro esse compressor vendo por 5 dólares 1 libra

Thanks for watching and commenting. This is the real way to recycle ♻️ !

Your time is money

Oh fuck the environment is what I always say.

It definitely is a lot of work but once you do the first one and figure out your systems it becomes very easy to knock them out quickly. I am glad that it was able to help. Thanks for commenting 🤝👍

Glad it was able to help you👍. With prices of scrap going up every piece counts 💰!! I just got my shop cleaned up and ready to go for some more videos. I appreciate the support thank you 🤝👍, as always remember to #ChallengeTheBuild

Thank you for watching and I am glad it helped 👍. With the scrap prices increasing it only makes this process even more worth while. Once you figure out your own little system it really does not take long to knock them out. Make sure to wear safety gear and be careful. Appreciate you taking the time to drop a comment, thank you..🤝👍

Thanks Sam for the great feedback, I do appreciate it. I'm having a hard time breaking out in KZfaq. If you can check out my updated scrap videos I linked one here, kzfaq.info/get/bejne/eLehpK-dvd-0YYE.html . Thanks again for the support. 👍🤝

Thank you so much for the encouragement.. Be safe and blessings to you as well..👍🤝🙌

Glad it was able to help. Thanks for watching and commenting. 🤝👍

@@ChallengeTheBuild hello

😊

No problem... Make sure to read the comments too... Some different opinions and ideas... This video is an updated version with even more info... kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html good luck and be safe.. Happy Scrapping...

Great! Thanks for the link to the new video!

Glad it helped! Thanks for watching and commenting. Happy scrapping! Be safe.🤙

Thank you 👍

Thanks for watching and commenting..🤙💯

Appreciate it, however this video kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html is an updated version showing a new method, plus the quality of the video is much better 👌 . Check it out when you get a chance...👍 Thanks for commenting.

Appreciate the watch and comment 👍 this video here is an updated video kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html new information and in my opinion better quality .. Thanks for watching and be safe.

Appreciate it, I strive to produce the best I can. I have a couple updated scrap videos which give weight brake downs along with new methods... They are a little longer but I made them that way so you can get a real sense of how much time it takes to do the job... Thanks for the comment... And if you have any questions don't hesitate...👍🤝

Gotta love them rainy buckets! 💪 Be safe and happy scrappin....

Thank you, this video is an updated version, kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html shows different techniques and more information.

Appreciate your input... Thanks

Awesome! Thanks for checking out the video and my channel. Good luck on the scrap run... every dollar counts!👍

Put a box fan to the side of you when cutting that's what I do.

Good idea...👍

Appreciate the watch. This video kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html was much better in video quality and in information, if you get a chance to watch... Thanks for the feedback 👍

This one is better...This is my updated video showing new methods and better quality. kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html

This is an updated video with some new techniques kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html .. Thanks for watching and commenting.

Glad it helped. 👍

Good thing he didn't seperate them into sheets then.

Thanks for watching and the comment.. I really appreciate it

Your welcome.. 👍🤝

Glad it helped, if you get a chance watch this updated video kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html , I show a new method of cutting the compressors apart, plus the overall quality of the video is better... Thanks again for watching and commenting. 👍

Absolutely!

When you do something you enjoy it's not work, its fun! 😁 Being able to make money investing your time into something you enjoy or find therapeutic, I don't think there's anything better..💪👍 Thanks for the comment, be safe!

Thank you 👍 I think my updated video is even better 😁 you can check it out here kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html when you have some time. 👍 Thanks for watching and commenting .

Thank you

This one is better! kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html Thanks for watching 👍

Thanks Mike, there is a little bit of updated info in this video, I sorta changed up my method a little bit kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html if you are interested.

This one is better! I show a new method here, kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html thanks for watching and commenting.

And to get started all you really need is an angle grinder in my opinion. It's also all about having a system, once you find a method that works for you it then becomes wash/rinse/repeat ! 🤝💪👍💯

It makes me happy to know the video has helped people worldwide to be more efficient when scrapping, glad it helped! Thank you for leaving a comment. Be safe and happy scrappin. 👍 🤝

Thank you...I have a couple updated scrap videos also... Appreciate the feedback...

I really appreciate the feedback, thank you! When you have some free time you may want to watch the updated video here kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html it doesn't get as much love. 😁 Again thanks for watching/subscribing and commenting. 👍😎

😁 Check out my updated video on the compressors, kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html Its a little long but on purpose so you can use it as a time gauge.. Watch it and then scroll around...I appreciate you and the support..👍🤝🙌

With the current prices its hard not to cut them up... Appreciate the comment, thank you.

Having a system definitely helps saves time and makes it worth it... Time is money 😁👍... Thanks for watching and commenting...

🇺🇲 🤝🥳 Appreciate you..💪 Go scrap um up😎🤑! Be safe!👍

Thanks Glenn, appreciate it..👍💯🤝

Thank you!

I had an idea to be able to use a log splitter, makes me happy to know someone is already there! Nice work. Time is money and the motors are worth it as long as you have a system! 👍💯🤙💪

This video is a little more in depth and I share a new method on how to scrap them kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html 👍

Don't let it intimidate you, take your time and once you get the first one under your belt you will see it is a very easy and straight forward process no matter what compressor you are working with. I have it down to about 10-15 minutes to scrap one out, it would go even faster if I had a plasma cutter. Just remember to do it safely and make sure you have fun too! I appreciate you taking the time to drop a comment thank you!

Check out my updated video kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html . This shows a new way to go about it. Thanks for watching. Good luck 👍

Thanks I appreciate it. I was in the garage stripping compressors over this weekend. I have a new faster updated method I want to share soon..

I think this one is better kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html 👍😁

Appreciate the kind words.. Thank you.

Thank you.. 👍🤝 Appreciate the comment...

Glad it was helpful ! I will be making a new updated video with a faster method regarding scrapping specifically the scroll type compressors here very soon. Time to debunk the "it's not worth it theory " 😁 Appreciate the comment 👍

I tried that method a few times and feel like it takes me longer...🤷‍♂️. I think it's important to gather all the methods and then just create a system that works for the individuals,. There's no wrong way as long as you complete the task and are safe... Appreciate the feedback 👍

@@ChallengeTheBuild I agree 100%.

There is no wrong way!!

@@scrappingonthefly77 well that depends if you are a full time scrapper or it's something you do on the side. Technically you're right but if you make a living at it the only right way is the fastest way or you're throwing away money.

Right I totally agree!! There's no wrong way.

Awesome! Thanks for watching, subscribing and commenting. 👍

Thank you. 👍 Still a work in progress. Appreciate you dropping a comment. 🤙🤝

I am happy that you found these videos as helpful as you did. There is definitely a lot of valuable info in them..

Thanks for the sub! 👍 I appreciate you

😁 Every person has their own unique way, some even have special tools specifically designed for scrapping these things, regardless the end goal is the same.. This is not a labor intensive job by any means, appreciate the wat h and comments... Scrap um up!😎👍

This video is better, I have revised methods. Watch this video when you get a chance. kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html

Never came across coated aluminum wire... And I never really looked that hard at it..😁👍

Not in compressor motors. Cheap pedestal fan motors, some household water pressure pump motors, nearly every microwave oven transformer and a few other ones. As soon as I access wire, I scratch test them with the stanley knife!

Appreciate tou watching and giving me the feedback, if you get a chance I made an updated video you can watch here kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html .... Let me know what you think 👍👍

Yeah, suckers are heavy! I would love to have a plasma cutter to help with a lot of things around the shop (scrapping being one of them) but I have a few obstacles to work through. Getting electric into the garage is the biggest.. Soon enough though. I appreciate you taking the time to drop a comment. Thank you!🤙

I've seen people use plasma cutters and they seem to work well (if you have one). As far as cut off wheels I use Benchmark Abrasives, harbor freight is good for some things, cutoff wheels isn't one of them (in my opinion) .. And my scrap yard buys the copper at #2 yours could be different 🤷‍♂️..

Doing the break down is definitely worth a shot... Try it and see if it's worth your time... It's all about finding a system when it comes to cutting them up and then wash, rinse, repeat. What works for me may not work for you but I am sure you will figure it out and then probably tell yourself why didn't I do this sooner... 🤷‍♂️. Good luck be safe.

Find a scrap yard that will take just drained compressors. It's hard to fill a 4x4 but the payday is unreal. I just threw about 46 by myself just over 3400 lbs I got.25 a pound. 😁 Happy day.

Depending on the scrap yards generally yes they will take them complete at cents on the dollar. I think the most I every got for a complete unit was around .20 cents a pound?

I very rarely see aluminum windings.

i did 2 ac compressors and 3 large motors last summer thinking i had a bunch of copper only to find out it was all copper clad aluminum not really worth the time it takes unless you know for sure its not ccp

Definitely a smart move... 🤌👍✌️🤑

@@ChallengeTheBuild it's still a greasy job

It definitely is, I always let them pile up and then spend a full day just on compressors just because of how dirty you get..👍👍

I had to go look, but one set I think came from advanced auto ( Pro Teq Set ) and the other was either home depot or craftsman, cant remember. Good luck and thanks for watching and commenting 👍!

They are sockets, sorry, completely missed that.. external torq E7 I think or E10 are sockets. 👍

@@ChallengeTheBuild Thanks for checking, appreciate it.

I use benchmark abrasive 5 inch wheel. Watch the full video here 👉 kzfaq.info/get/bejne/mbZ5l7B017HDmH0.html ... I talk about the tools needed plus what cutting wheels to use in the video.

Lots of different ways to go about the scrap process... I don't think there is a right or wrong way as long as it's done safely..👍

@@ChallengeTheBuild you are absolutely correct, as years go by we learned and will discover easier ways..

I think you will be surprised at how easy it is once you figure out your system, and with the prices up it definitely makes it worth your time in my opinion. Good luck and be safe. 👍scrap um up !

If you get a chance I did a more detailed breakdown along with new method for cutting them apart. Its a longer video but I did it that way so you get an idea if actual time it takes. Here is the video link kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html

@@ChallengeTheBuild thanks, i like your "modified" screwdriver, scrappers really go thru screwdrivers, beware of those composite metal tools, they're junk, you can easily tell they aren't steel.

Thanks for watching and commenting... I really appreciate it

It's possible... But I never spent any time looking into it. 👍

Great great question.. It really all depends on whos buying your scrap metal... The guy I take it to agreed to buy it all as #2, where I think some of it should be considered bare brite (atleast the super clean stuff).🤷‍♂️ It all depends how clean you get it and who buys it.. Remember TIME is money so weigh out your time when sorting.. Is it worth your time 🕚 to sort for an extra hour (just an example) to get paid another 20-30 cents per pound? Since scrap is becoming a hot item I am going to be making a revised/updated video on this topic... so subscribe and keep watch for it.. be safe and thanks for the comment..

I'd imagine a lot? Never had one before. Similar to the smaller units just super sized? I have seen some larger compressors at the scrap yard and always wonder 🤔 about such things... Sounds like you may have to cut one apart and see if it's worth it? I bet you it will be worth it especially considering the prices right now... My guess is 10-15lbs of copper not to mention probably a big hunk of cast iron too... good luck 👍 wear safety gear and be safe. Thanks for leaving a comment. 🤝

@@ChallengeTheBuild thats what i was thinking too. ill update tomorrow when i do it

I have it sitting in gallon jugs for now, and plan on mixing it with my regular waste oil then burning it in a waste oil heater...

I just recycle it with my motor oil..

Goes quickly when you have a system..👍

I use Benchmark Abrasives....👍

I've never seen or heard of aluminum windings in any electric motors. It definitely is copper but it does have a coating which makes it #2 copper, rather than bare brite... I would be finding another scrap yard to get a second opinion if there is any doubt.. Take any electric motor and look at the windings, if you are ever in question about what material you have take a hand file and look at the coloring of it after filling ....

That sounds like a good haul especially for wall units. I definitely feel like its worth the time to cut them apart, even with scrap price dropping. I will still continue cutting them up and then just sit and wait for copper prices to rise again..🤷‍♂️. Thanks for taking the time to drop a comment! I appreciate you. 🤙

@@ChallengeTheBuild yeah I scrap as a hobby so I don't get a ton so I can store the copper I do get without it taking up a ton of space. Question. I do still have 10 of the aluminum copper radiators too. Some are pretty thick, 5 rows. Will those go up a good bit of copper goes up? I am contemplating sitting on those too since it's about 60lbs. If they can possibly go up significantly over the next few years I can hold on, of not I'll just sell em.

@@E150GT its hard to tell what prices are gonna do? A few months ago copper/aluminum rad was about $1.00 lb +/- now it's .70 cents +/- and continues to fall. So its a tough call? I scrap for extra pocket money to fund all my projects so I dont mind sitting on it but at the same time if I need a couple extra dollars I cash in because its more than what I had, the nice thing is the copper aluminum rad stacks nicely.

I get a lot of comments regarding this and I can tell you that I have always gotten paid #2 copper every time I've cashed in my scrap motor windings. I've cut a lot of them apart and have never had any question of whether it was copper or copper coated aluminum. 🤷‍♂️

Right on! Especially if you get them for free, the R.O.I is huge! 😁🙌🙌💰💪 Be safe and God bless!🇺🇲

I really don't know... Maybe 5-10 bucks? Never messed with anything like that...

😂😂😂👍

I didn't/don't pick them up unless the refrigerant was already removed...

Thank you, this is an updated video on the topic, kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html much better quality in my opinion.. Thanks for watching. 👍

I am not sure about this...

Glad it helped, I have been wanting to make a new video about this topic because I have figured a way to improve on the process & time is money.. As far as the copper... GREAT QUESTION... I myself have questioned this...Talking with the scrap yard I deal with, he has agreed to buy it as #2 copper, I have questioned him and asked why the clean stuff can't be bought at bare bright prices which is even higher then #1...the one day he even commented and said "wow this is some really clean heavy copper" ... all that to say I'd talk with your scrap buyer to see what he is willing to do? Once you get into a system with breaking them down, you should be able to do 4-6 of them in an hour with price per unit around $12-$15 per unit once everything is sorted light/heavy/copper... not bad $$ and most everyone over looks them...I have a short version of this video if you need to refresh.... Thanks for the comment..👍👍

@@ChallengeTheBuild I'd like to see that video. Maybe tear down a different style. Sorry I am a late subscriber to your channel. I noticed it's been 11 months since your last video. I hope of y'all are alright.

All good, I hit YT hard right outta the gate and burnt myself out, plus with working on my project truck so much, I started running out of funds $$. I want to make sure my videos have quality content in them and not just random acts of video... I give the full time you tube personalities alot of credit for what they do... I appreciate you subscribing and will do my best to get some new content up soon... 👍👍

@@ChallengeTheBuild , I am glad all is well! I agree with you about the full time YT personalities. Take your time. Come back when you are ready, not what others want. Merry Christmas and a Happy New Year. Be safe and stay healthy.

My yard buys the hammered out copper as # 2 copper mostly because of the enamel (red colored insulating coating) on the windings and because of oil contamination.

Im sure it is at some level, that's why its important to work in a well ventilated area and for added safety you could always use a respirator with proper cartridges.

That's what I said looked too white to me I just came across one was like that I was not too happy after doing all the work to get to it to see it!

If you get a chance watch this updated video... kzfaq.info/get/bejne/iq6cZddk2tS0oKc.html 👍👍 Thanks for watching..

I will keep a lookout for them, thanks. 🤘🤑 happy scrappin!