How to Set up Band Saw for Straight and Accurate Cuts || Bandsaw Tune up

Рет қаралды 9,122

Күн бұрын

If you are having trouble with your band saw not cutting straight, you should watch this video.
It's a simple guide on how to set up a band saw for accurate cuts. All shrunk to just over 10min.
Featuring Scheppach HBS261 budget band saw
(Also sold in Aldi as Ferrex HBS261 10'')
I've had the saw since June 2021 and have been using it on few projects. Some of which will be featured on this channel.
I am not being sponsored by anyone and purchased the saw using my own money.
The video covers few chapters and you can navigate through them easily on your timeline.
However I give comments as I go along so for the best experience watch them all.
Bandsaw boxes made on this saw
• Bandsaw Box with Commo...
Timeline
00:00 - 00:06 Channel Intro
00:06 - 00:50 Video Introduction
00:50 - 01:48 Setting up traction and tension
01:48 - 03:27 Setting blade guides
03:27 - 04:09 Leveling table
04:09 - 05:08 Setting fence
05:08 - 07:06 Aligning table to blade
07:06 - 09:16 Test cuts
09:16 - 09:47 Miter gauge fix
09:47 - 10:12 Video ending
Video music by: Elevated Jam Tracks
Track- 217 Dark Blues Rock Guitar Backing Track Jam from Elevated Jam Tracks - Full Digital Discography (Part 2) - Elevated Jam
• Dark Blues Rock Guitar...
elevatedjamtracks.bandcamp.com

Пікірлер: 28

@ianvicedomini2648 4 ай бұрын

Finally, I've found a chanel where the host explains clearly how to set a bandsaw up. You've made my day mate. Thank you very much. Subbing right now.

@pscraftydiy 4 ай бұрын

Glad I could help and thank you for your support.

@certifiedspeedfreak Жыл бұрын

Thank you for actually making a video where the person talks about what they are supposed to be doing ! it' makes such a difference to watch a video where who ever is speaking doesn't rattle on about how long they have been a woodworker etc etc. Well done i watched this and have done exactly the same to my bandsaw which now works perfectly Keep up the good work :)

@pscraftydiy Жыл бұрын

Thank you very much.

@colind2955 Ай бұрын

Excellent video ,well explained and visually displayed many thanks. Best so far I have seen

@pscraftydiy Ай бұрын

Many thanks much appreciate your support

@tmiller499 Ай бұрын

I made the comment below before the video was finished. There were several other awesome tips at the end. Again, thanks! I subscribed.

@pscraftydiy Ай бұрын

Thank you for your support

@johnreilly4577 Ай бұрын

Very good video, explains and shows the set up so well.

@pscraftydiy Ай бұрын

Thank you

@tmiller499 Ай бұрын

What a GREAT setup tutorial for a band saw. My band saw has given me so many problems that I feel like it is a worthless tool. You have given me hope that it will be a very useful tool. I need to work through all of the adjustments you suggest. I'll reply later how it works after all of the adjustments. Thanks for the video!!!

@pscraftydiy Ай бұрын

Thank you, the key along with the good set up is a good quality blade. I've spent ages fettling with set up but it would never perform the way I wanted to until I got decent blades in it. It makes all the difference. The blades that came with the saw were too thin and flimsy comparing too good quality blades. You'll get better and quicker with the set up each time you do it. Once you get there you'll find that properly tuned bandsaw is very versatile and useful tool. Makes less waste, mess, noise and uses less power.

@utuberick1 Ай бұрын

Excellent video! Absolutely exactly what I needed and I’m sure for the other 8K viewers too. It sounds like you have a Dutch accent, true?

@pscraftydiy Ай бұрын

Thank you much appreciate your support. Haha not Dutch although I get that from people all the time. I am Czech but lived in the UK for just over 20 years.

@stephenyoud6125 8 ай бұрын

Great well done

@pscraftydiy 8 ай бұрын

Thank you...

@stephenyoud6125 8 ай бұрын

@@pscraftydiy I have a problem with my Scheppach bandsaw, the blade is running very close to the front edge of the lower wheel and i cannot adjust it to the centre. The to wheel can be adjusted to the centre but the bottom wheel not, and the cut is pulling to the right on 6mm MDF. Its like the whole motor assembly and shaft is titled upwards. I was going to try adding two washers on the motor side of the lower two motor bolts to try and tilt the motor upwards and the wheel end of the shaft downwards a bit.

@Secbra1 8 ай бұрын

@@stephenyoud6125Did you try run a proper blade in this or are you using the one that came with the saw as they are rubbish. Lot of problems people having are down to poor quality blade. The bottom wheel is not directly driven by the motor. Its driven by a drive belt and a pulley fitted on the motor so if the motor shaft would be out of the line like you suggesting it would be the drive belt slipping off not your blade. The bottom wheel centre can be adjusted by 4 screws at the back of the saw near its shaft. I am not sure if these only shift the wheel centre left/right and up/down or if you able to adjust the shaft alignment on these as well, meaning to tilt the shaft. I'd be very careful about this adjustment done on these 4 bolts as these should be set in factory and you should never have to touch those. I'd try to get in touch with Scheppach and ask them for advice or if there is any procedure they could have for you to follow to get the wheels coaligned. If your saw is new I'd try to return it as faulty as the flat backing could be bowed or bent, they should give you a new one or your money back.

@stephenyoud6125 8 ай бұрын

@@Secbra1 Mine us a different model: BASA1 and definitely seems to be direct drive from the motor armature to the bottom wheel. the 4 bolts seem to hold the motor on directly and dont offer any tilkt adjustment as that I think is what is needed: to tilt the bottom edge of the bottom wheel down. And yes I'm using the blade that came on the machine. No matter what I do I cannot shift the blade from run right on the front edge of the lower wheel. I think this is what is causing the cut to pull to the right as the excesive forward tilt of the blade by running so close to the front edge of the lower wheel (the teeth are actually overhanging the edge) is causing the blade to twist and this is steering the cut to the right. I wrote to Scheppach but they only sent an auito generated reply saying they are busy and will get to me later. I tried adjusting the blade guide rollers but had to file quite a bit on the lower outside guard, below the table to get it to fit past the thrust bearing behind the blade. Looks like a Friday afternoon machine

@Secbra1 8 ай бұрын

@@stephenyoud6125Alright I see. In that case tilting the motor with washers/shims makes sence. I'd really try to run a proper blade in it firs and see if that gets you anywhere. I had lot of trouble with getting mine cutting straight, tried absolutely everything and it was still running off. I was convinced there is something wrong with the saw as Ive tried both blades supplied with the machine one was running off to the right and the other to the left. That's when I realised and ordered different blade from reputable manufacturer and it was like night and day.

@xstreetfighter1 Жыл бұрын

I really like your videos, very useful. Are you able to make a video how to adjust and sharp chain on chain saw? And I would like to recommend you Tormek company. I have had Tormek T8, Very useful equipment for people who is interested in wood "business".

@pscraftydiy Жыл бұрын

Thank you for the kind words. Unfortunately I do not own a chainsaw and have never attempted to sharpen it. I had a look into Tormek T8 in tha past. Although it seems to be a great machine for sharpening I have quickly dismissed it due to its price tag which I cannot justify as a weekend warrior.

@arkledovinar 11 ай бұрын

My still drafting to the right on the 42x 42. I got like a 1 mm bow cut. Is my sow still louse or?. I did everything like in the video . thanks for your help keep up the good work. You are awesome 👍

@pscraftydiy 11 ай бұрын

I am sorry to hear that. What blade are you using? If the one that came with the saw, You'll never get that cutting straight, I couldn't either. Buy a good blade and it should cure. Also see if the blade is not oscilating side to side. Some people had a problem with that, if thats the case there is not much you can do but take the saw back. Hope that helps

@oldb-1kenobi 3 ай бұрын

Hello, what model is your bandsaw? It looks just like my Scheppach but yours has much more substantial bearings, table , blade, etc..

@pscraftydiy 2 ай бұрын

Hi mine is a Scheppach HBS261 got it from screwfix. Sometimes it is available on Aldis website under their own brand Ferrex HBS26 and much cheaper. There is a full review I have done on my channel.