How to Sharpen Sawmill Blades [DIY] ┃Save Money Homemade Sawmill Blade Sharpener

No video

How to Sharpen Sawmill Blades [DIY] ┃Save Money Homemade Sawmill Blade Sharpener

Рет қаралды 11,178

Күн бұрын

How to Sharpen Sawmill Blades [DIY] ┃Building a Homemade Sawmill Blade Sharpener
💎 We begin with the reasons why you want to sharpen sawmill bandsaw blades by hand. Building a sawmill blade sharpener is simple and we show you how. This video will show you how to resharpen WoodMizer blades and save you money and time. How to hand sharpen band sawmill blades is cheap, easy, and effective. We sharpen blades with a chainsaw blade sharpener and convert it into a sawmill blade sharpener.
💎 WATCH Sawmill Blade Sharpness TEST: [DIY] Homemade Sawmill Blade Sharpener vs. Factory New (Part 2) where we test the sharpened blades against brand new factory blades. The results are surprising!
• How to Sharpen Sawmill...
💎 We are sawmilling with the Wood-Mizer LT-40. If you want to see this sawmill in action watch
"Sawmilling BIG Logs on Wood-Mizer" (Part 5 of "Logs to Lumber")
👉Part 5 ►MILLING►► • How it's Made LOGS to ...
⏰TIME STAMPS:
0:00 Intro
:37 Four reasons to sharpen blades yourself
3:50 Brief overview of sawmill blade teeth
5:07 How much & what to sharpen
5:43 Blade thicknesses
6:27 Microcracking
8:13 Blade sharpness under a microscope
8:50 Homemade blade sharpener
11:21 Walking through the sharpening steps
12:41 Sharpening the blades
13:13 Adjusting the angle
14:44 Inspecting the sharpened teeth
15:19 The sharpening process in action
15:38 Tips on sharpening the blade
16:40 Grinding wheel options
18:06 "Sound-vision" (sharp blade sound vs. dull blade)
#sawblade #sawmill #chainsawsharpener #woodworking #woodmizer #lt40 #lumber #sharpening #blade #bandsaw #sharpening #diy #howto
💬COMMENT
Got a QUESTION? COMMENT BELOW!
⭐SUBSCRIBE - Don't miss a thing!
youtube.com/@C..."
👍LIKE & SHARE
/ @cobblecreekcabins
📽️If you liked this video, CHECK out our Sawmill & Lumber Adventures PLAYLIST
• Sawmill & Lumber Adven...
Thanks for watching 😊
Stacy 💙 Troy

Пікірлер: 36

@CobbleCreekCabins 10 ай бұрын

💬COMMENT Got a QUESTION? COMMENT BELOW! ⭐SUBSCRIBE - Don't miss a thing! youtube.com/@CobbleCreekCabins?si=FOGAVQDl_KY62Bz4" 👍LIKE & SHARE kzfaq.info/love/hnMH7OUSvCHxHISYKMyXNg

@bowlweevil4161 2 ай бұрын

if you take a small bright led flashlight and shine it on the face of the tooth after you have sharpened it one stroke the reflection from the sharprned surface will show you how the stone is contacting the tooth and if needed make adjustments. I waer a small headlamp so I don't have to fool with flashlight

@lectro88 6 ай бұрын

Update; Man I shaped a grinding wheel to match my blades and had good success,. or way better than what I had. Problem is it was time consuming. I know that my blades cut like a razor,.... But.. I also know holding the blade by hand I'm getting some variations in angles and depth,. don't get me wrong I had surprising results by hand, considering. I again was using a full on bench grinder not the chainsaw grinder. But I have now gone to the Dark Side..... And sprung for a RS30 with setter from Woodland. Reason for this ... I fell into a supply of muddy and rock filled logs, and I can only clean so much(I miss a little here and there) So motivation got the best of me. I know that I am going to be sharpening A LOT more blades AND (more frequently....) And can't just be waiting for Rainy Days. On a side note,. My wallet, or paper fold is Less now. Like you said, a sawmill is nothing without blades(Blades are a Vital...REQUIREMENT) Cheers and thanks for helping me along.

@CobbleCreekCabins 6 ай бұрын

Put A video up and take on clients. Make some of that money back. Just don't keep peoples blade for little or no reason.

@daveb8598 11 ай бұрын

This is great, thank you! Setting up my sawmill soon and really want a way to sharpen at home that isn't crazy expensive. This seems like a good way to go.

@CobbleCreekCabins 11 ай бұрын

It's the best I've been able to come up with after half a dozen attempts or so. Take your time I'm sure you'll get the hang of it. Thank you for the comment

@willcoe8419 9 ай бұрын

I use an auto drag sharpener and found it important to re dress the face about every 8 blades . If not you can get negative rake. Ask me how I know 😮

@CobbleCreekCabins 9 ай бұрын

⁠@@willcoe8419Thanks I'll have to look up auto drag sharpener. I know what your saying about the negative rake. It's a thing

@pauljensen7518 7 ай бұрын

I have been trying this method, but seems like I cant saw very long, and some blades just want to wander down or up in the cut. i am thinking the blade should be set? what are your thoughts?

@CobbleCreekCabins 7 ай бұрын

Make sure you don't blue or loose the temper on the very tip of the tooth, very easy to do, that could possibly explain why they dull fast.. Consistency is important/crucial. If your taking more off of one side of blade than the other it may start to walk, incorrect blade guide set up is another culprit. Blade tooth set is more quality of cut, rough vs smooth, in my opinion. If your having some blades cutting correctly your doing it right just not all the time. Hope that helps.

@Chris-qf9qm 8 ай бұрын

Good vid, thanks for sharing

@CobbleCreekCabins 7 ай бұрын

Glad you enjoyed it. Hope it helps.

@DJLEE_77 Жыл бұрын

Love the inventive way you came up with to sharpen them! How much use do you get out of a blade before it cracks/fails?

@CobbleCreekCabins 11 ай бұрын

Typically 4-5 resharpenings before they give up the ghost. Nice question and thanks for watching.

@dubya2514 7 ай бұрын

I built a similar one, with a custom base, I can get my blades sharper than factory, and they cut better.👍

@CobbleCreekCabins 7 ай бұрын

Sweet, its so satisfiying isn't it.

@DANG-- 8 ай бұрын

Very neat idea. How many sharpening's are you getting out of a blade? After you have sharpened a blade about 7 times or so, Have you every measured the teeth spacing?

@CobbleCreekCabins 8 ай бұрын

My blades have only lasted about 3-5 sharpenings before metal fatigue and failure, or run into metal. Hope that helps

@lectro88 8 ай бұрын

I have surprisingly sharpened with a file with good results, but my beard got longer before I was done. Have trust issues.... that I will actually get MY blades back that I sent and not somebody else's that has been sharpened 3x's already. ETC.... Shop guys swear only they can sharpen blades, chainsaw shops are the same.... News break, I can sharpen too.... I just have to get past that learning curve..... and then setting... Cheers. got a thumbs up...

@CobbleCreekCabins 8 ай бұрын

Excellent, thank you.

@approots 8 ай бұрын

I find that with this technique eventually a tiny groove forms in the grinding wheel that takes the top of the tooth off.

@CobbleCreekCabins 8 ай бұрын

Ya thats been mentioned previously, after a bit I just redress the wheel. A diamond grinding disk would be ideal.

@alexandrugajin763 8 ай бұрын

I think you should use a circular blade saw sharpening disc. It has an outer rim glued to it made of diamon dust or something like that. Buy a good quality one and it will last a very long time. I have one and i sharpen all my saw blades, i have also made a jig to sharpen drill bits. And keep in mind the circular saw blades have carbite teeth. It hasn't changed it's shape a bit, still flat. The downside is, the rim wich has the diamond stone is only on one side and is pretty slim. But compared to the stone you're using that sharpens just like factory. You have to keep in mind that the disc, must be perfectly balanced in centerd in the axle. The problem with normal sharpening stones is that the steel eats them as you grind and if you only use one little side of the stone all the time it will make a small gove in there wich will ruing the sharpening of the most important part, the tip of the tooth.

@CobbleCreekCabins 8 ай бұрын

Excellent, maybe I can find one that will match my arbor.

@alexandrugajin763 8 ай бұрын

or you can use the grinder itself to make an adapte from wood or mdf. I made mine from a piece of laminate flooring. You just need a drill bit of the shaft diameter and some pieces of wood to form a jig so you can shave it with a chisel. What centers the disc is those 2 washers from the grinder's shaft, basicly you just need a ring to match the holes.@@CobbleCreekCabins

@E-BikingAdventures 7 ай бұрын

Good detailed explanations, but could of done without all the irritating annoying noises you were making.

@CobbleCreekCabins 7 ай бұрын

At least you get to walk away, how do you think I feel. LOL! Thanks for watching

@jimbauer6822 2 ай бұрын

Very inconsistent way to try no tooth I'd the same height won't work well unless your very lucky

@williamrowe5298 5 ай бұрын

If you gotta sharpen a blade sharpener a blade don't talk.

@Ricochet1957 9 ай бұрын

I believe after watching your video and seeing how you sharpen your blades this is a better way. Any chance you can share you neighbor's contact info for the grinder? I'd like to buy one from him and help out his cause.

@CobbleCreekCabins 9 ай бұрын

Hey! Thanks for your comment and wanting to help the cause...at this time he is sold out but they are all over the internet (though may be badged differently)...be sure to get one with the same adjustability...Thanks for watching 😊

@jimbauer6822 9 ай бұрын

Great way to ruin your blades horrible job I know I have do e it just like this np control of how much you take off the face so the teeth are never the same